SIST EN ISO 4823:2001/A1:2008
Dentistry - Elastomeric impression materials - Amendment 1 (ISO 4823:2000/Amd 1:2007)
Dentistry - Elastomeric impression materials - Amendment 1 (ISO 4823:2000/Amd 1:2007)
Zahnheilkunde - Elastomere Abformmassen (ISO 4823:2000/FDAM:2007)
Diese Ergänzung zu ISO 4823:2000 nimmt elastomere Abformmassen vom Typ 0 (knetbar) aus der Übereinstimmung mit der Erfüllung der Anforderung an die Verarbeitungszeit, wie sie in 6.3 festgelegt ist.
Art dentaire - Produits pour empreintes, a base d'élastomeres - Amendement 1 (ISO 4823:2000/Amd 1:2007)
Zobozdravstvo - Elastomerni materiali za odtise - Dopolnilo 1 (ISO 4823:2000/Amd 1:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4823:2001/A1:2008
01-april-2008
Zobozdravstvo - Elastomerni materiali za odtise - Dopolnilo 1 (ISO 4823:2000/Amd
1:2007)
Dentistry - Elastomeric impression materials - Amendment 1 (ISO 4823:2000/Amd
1:2007)
Zahnheilkunde - Elastomere Abformmassen (ISO 4823:2000/FDAM:2007)
Art dentaire - Produits pour empreintes, a base d'élastomeres - Amendement 1 (ISO
4823:2000/Amd 1:2007)
Ta slovenski standard je istoveten z: EN ISO 4823:2000/A1:2007
ICS:
11.060.10
SIST EN ISO 4823:2001/A1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 4823:2000/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2007
ICS 11.060.10
English Version
Dentistry - Elastomeric impression materials - Amendment 1
(ISO 4823:2000/Amd 1:2007)
Art dentaire - Produits pour empreintes, à base Zahnheilkunde - Elastomere Abformmassen - Änderung 1
d'élastomères - Amendement 1 (ISO 4823:2000/Amd (ISO 4823:2000/Amd 1:2007)
1:2007)
This amendment A1 modifies the European Standard EN ISO 4823:2000; it was approved by CEN on 30 June 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4823:2000/A1:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 4823:2000/A1:2007 (E)
Foreword
This document (EN ISO 4823:2000/A1:2007) has been prepared by Technical Committee
ISO/TC 106 "Dentistry" in collaboration with Technical Committee CEN/TC 55 "Dentistry", the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2008, and conflicting national
standards shall be withdrawn at the latest by January 2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
Endorsement notice
The text of of ISO 4823:2000 has been approved by CEN as EN ISO 4823:2000/A1:2007
without any modifications.
2
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 4823
Third edition
2000-12-15
AMENDMENT 1
2007-07-01
Dentistry — Elastomeric impression
materials
AMENDMENT 1
Art dentaire — Produits pour empreintes, à base d'élastomères
AMENDEMENT 1
Reference number
ISO 4823:2000/Amd.1:2007(E)
©
ISO 2007
---------------------- Page: 4 ----------------------
ISO 4823:2000/Amd.1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this
...
SLOVENSKI SIST EN ISO
4823:2001/oprA1:2006
PREDSTANDARD
julij 2006
Zobozdravstvo - Elastomerni materiali za odtise - Dopolnilo 1 (ISO
4823:2000/DAM 1:2006)
Dentistry - Elastomeric impression materials - Amendment 1 (ISO 4823:2000/DAM
1:2006)
ICS 11.060.10 Referenčna številka
SIST EN ISO
4823:2001/oprA1:2006(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
EN ISO 4823:2000
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2006
ICS
English Version
Dentistry - Elastomeric impression materials - Amendment 1
(ISO 4823:2000/DAM 1:2006)
Art dentaire - Produits pour empreintes, à base
d'élastomères - Amendement 1 (ISO 4823:2000/DAM
1:2006)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 55.
This draft amendment A1, if approved, will modify the European Standard EN ISO 4823:2000. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status
as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4823:2000/prA1:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 4823:2000/prA1:2006 (E)
Foreword
This document (EN ISO 4823:2000/prA1:2006) has been prepared by Technical Committee
ISO/TC 106 "Dentistry" in collaboration with Technical Committee CEN/TC 55 "Dentistry", the
secretariat of which is held by DIN.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 4823:2000 has been approved by CEN as EN ISO 4823:2000/prA1:2006
without any modifications.
2
---------------------- Page: 3 ----------------------
DRAFT AMENDMENT ISO 4823:2000/DAmd 1
ISO/TC 106/SC 2 Secretariat: ANSI
Voting begins on: Voting terminates on:
2006-04-13 2006-09-13
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Dentistry — Elastomeric impression materials
AMENDMENT 1
Art dentaire — Produits pour empreintes, à base d'élastomères
AMENDEMENT 1
ICS 11.060.10
ISO/CEN PARALLEL ENQUIRY
The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject
of interest to European standardization. In accordance with the ISO-lead mode of collaboration as
defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN
members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a
final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS
vote in ISO and formal vote in CEN.
In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.