iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 50152-1:1998

(Main)

Railway applications - Fixed installations - Particular requirements for a.c. switchgear -- Part 1: Single-phase circuit-breakers with Um above 1 kV

Railway applications - Fixed installations - Particular requirements for a.c. switchgear -- Part 1: Single-phase circuit-breakers with Um above 1 kV

This EN 50152-1 is applicable to single-phase a.c. one-pole circuit-breakers designed for indoor or outdoor fixed installations for operation at frequencies of 16 2/3 Hz and 50 Hz on traction systems having an UNm above 1 kV up to 52 kV. This EN 50152-1 is also applicable to two-pole circuit-breakers when connected in the following manner: one pole supplying the connection to the contact line of the track, the second pole supplying the connection to the feeder cable which runs alongside the same track and which is used to boost the track voltage at regular intervals in combination with autotransformers. The centre of this circuit is connected to earth. This standard is also applicable to the operating devices of circuit-breakers and to their auxiliary equipment. This standard does not address circuit-breakers with dependent manual operating mechanism. NOTE: A rated short-circuit making current cannot be specified for these circuit-breakers and the use of these mechanisms may give reasons for the objection based on their safety in operation

Bahnanwendungen - Ortsfeste Anlagen - Besondere Anforderungen an Wechselstrom-Schalteinrichtungen -- Teil 1: Einphasen-Leistungsschalter mit Um über 1 kV

Železniške naprave – Stabilne naprave električne vleke – Posebne zahteve za stikalne naprave za izmenični tok – 1. del: Enofazna močnostna stikala z Um nad 1 kV

General Information

Status
Withdrawn
Publication Date
31-Oct-1998
Withdrawal Date
16-Jan-2008
ICS
29.130.99 - Other switchgear and controlgear
29.280 - Electric traction equipment
Technical Committee
ŽEN - Electrical applications for railways
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
07-Jan-2008
Due Date
30-Jan-2008
Completion Date
17-Jan-2008
Mandate
M/024 - Mandate to CEN/CENELEC/ETSI for programming and standardization in the field of railway equipment
Ref Project
EN 50152-1:1997 - Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 1: Single-phase circuit-breakers with Um above 1 kV

Relations

Replaced By
SIST EN 50152-1:2008 - Railway applications - Fixed installations - Particular requirements for a.c. switchgear -- Part 1: Single-phase circuit-breakers with Un above 1 kV
Effective Date
13-May-2010
Replaced By
SIST EN 50152-1:2008 - Railway applications - Fixed installations - Particular requirements for a.c. switchgear -- Part 1: Single-phase circuit-breakers with Un above 1 kV
Effective Date
28-Jan-2023
Replaced By
SIST EN 50152-1:2008 - Railway applications - Fixed installations - Particular requirements for a.c. switchgear -- Part 1: Single-phase circuit-breakers with Un above 1 kV
Effective Date
07-Jun-2022
Replaced By
SIST EN 50152-1:2008 - Railway applications - Fixed installations - Particular requirements for a.c. switchgear -- Part 1: Single-phase circuit-breakers with Un above 1 kV
Effective Date
01-Apr-2008

Buy Standard

EN 50152-1:1998EN 50152-1:1998
PreviousNext
Standard
EN 50152-1:1998
English language
59 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50152-1:1998
01-november-1998
äHOH]QLãNHQDSUDYH±6WDELOQHQDSUDYHHOHNWULþQHYOHNH±3RVHEQH]DKWHYH]D
VWLNDOQHQDSUDYH]DL]PHQLþQLWRN±GHO(QRID]QDPRþQRVWQDVWLNDOD]8PQDG
N9
Railway applications - Fixed installations - Particular requirements for a.c. switchgear --
Part 1: Single-phase circuit-breakers with Um above 1 kV
Bahnanwendungen - Ortsfeste Anlagen - Besondere Anforderungen an Wechselstrom-
Schalteinrichtungen -- Teil 1: Einphasen-Leistungsschalter mit Um über 1 kV
Ta slovenski standard je istoveten z: EN 50152-1:1997
ICS:
29.130.99 Druge stikalne in krmilne Other switchgear and
naprave controlgear
29.280 (OHNWULþQDYOHþQDRSUHPD Electric traction equipment
SIST EN 50152-1:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 2 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 3 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 4 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 5 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 6 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 7 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 8 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 9 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 10 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 11 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 12 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 13 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 14 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 15 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 16 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 17 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 18 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 19 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 20 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 21 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 22 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 23 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 24 ----------------------

SIST EN 50152-1:1998

---------------------- Page: 25 ----------------------

SIST EN 50152-1:1998

---------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST-TS CLC/TS 50152-4:2021(Main)
Railway applications - Fixed installations - Particular requirements for AC switchgear - Part 4: AC metal-enclosed traction switchgear
CLC/TS 50152-4:2021

This part of EN 50152 specifies requirements for prefabricated metal-enclosed traction switchgear for alternating current of traction voltages and frequencies as specified in EN 50163:2004 and used in indoor and outdoor installation. Enclosures may include fixed and removable components and may be filled with fluid (liquid or gas) to provide insulation.
NOTE 1 EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz
NOTE 2 This standard applies to single-phase or two-phase systems.
For metal-enclosed traction switchgear containing gas-filled compartments, the design pressure is limited to a maximum of 300 kPa (relative pressure).
NOTE 3 EN 62271-203 can be used as a guide for design and testing in case the design pressure of gas-filled compartments exceeds 300 kPa (relative pressure).
Components contained in metal-enclosed traction switchgear are to be designed and tested in accordance with their various relevant standards. This document supplements the standards for the individual components regarding their installation in traction switchgear assemblies.
This document does not preclude that other equipment may be included in the same enclosure. In such a case, any possible influence of that equipment on the traction switchgear is to be taken into account.
NOTE 5 Switchgear and controlgear assemblies having an insulation enclosure are covered by EN 62271-201. For definition see there or IEV 441-12-06.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50152-3-1:2017(Main)
Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 3-1: Measurement, control and protection devices for specific use in a.c. traction systems - Devices
EN 50152-3-1:2017

This draft European Standard is applicable to new low voltage devices for measurement, control and protection which are:
-   for indoor or outdoor fixed installations in traction systems, and
-   operated in conjunction with high voltage equipment with an a.c. line voltage and frequency as specified in EN 50163.
NOTE   EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz.
This draft European Standard will also be applied to measurement, control and protective devices other than low voltage devices and not covered by a specific railway product standard as far as reasonably possible. Requirements of this document prevail.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50152-3-3:2017(Main)
Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 3-3: Measurement, control and protection devices for specific use in a.c. traction systems - Single-phase inductive voltage transformers
EN 50152-3-3:2016

This EN 50152-3-3 is applicable to new voltage transformers which are
   for indoor or outdoor fixed installations in tractions systems, and
   operated with an a.c. line voltage and frequency as specified in EN 50163.
NOTE 1   EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz.
As rails of a.c. traction systems are connected to earth and included in the return current path all phase to earth voltages will be within the tolerances as specified in EN 50163. Nevertheless phase to phase voltages may be higher e.g. in autotransformer systems.
Voltage transformers are mainly used with
   measurement instruments,
   protective devices.
This EN 50152-3-3 shall also be applied to voltage transformers other than inductive types as far as reasonably possible. Requirements of this EN 50152-3-3 prevail.
NOTE 2   Combined current and voltage transformers also capacitive voltage transformers are typically not used in fixed installations.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50152-3-2:2017(Main)
Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 3-2: Measurement, control and protection devices for specific use in a.c. traction systems - Current transformers
EN 50152-3-2:2016

This EN 50152-3-2 is applicable to new current transformers which are
   for indoor or outdoor fixed installations in tractions systems, and
   operated with an a.c. line voltage and frequency as specified in EN 50163.
NOTE 1    EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz.
As rails of a.c. traction systems are connected to earth and included in the return current path all phase to earth voltages will be within the tolerances as specified in EN 50163. Nevertheless phase to phase voltages may be higher e.g. in autotransformer systems.
Current transformers are mainly used with
   measurement instruments,
   protective devices.
This EN 50152-3-2 shall also be applied to current transformers other than inductive types as far as reasonably possible. Requirements of this EN 50152-3-2 prevail.
NOTE 2   Combined current and voltage transformers are typically not used in fixed installations.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50123-6:2003/A1:2015(Amendment)
Railway applications - Fixed installations - D.C. switchgear -- Part 6: D.C. switchgear assemblies
EN 50123-6:2003/A1:2014

This European Standard covers d.c. metal-enclosed and non-metallic enclosed switchgear
assemblies used in indoor stationary installations of traction systems, with nominal voltage
not exceeding 3 000 V.
It is intended that individual items of equipment, for example circuit breakers, housed in the
assembly are designed, manufactured and individually tested (simulating the enclosure when
necessary) in accordance with their respective parts of EN 50123 or, when appropriate, with
another applicable standard.
NOTE 1 The requirements covered in this European Standard are those concerning the assembly as such, its
enclosure and the mutual influence of the equipment enclosed.
NOTE 2 EMC requirements are covered by EN 50121-5 and additional requirements concerning dependability
(RAMS) are covered by EN 50126.

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50123-4:2003/A1:2014(Amendment)
Railway applications - Fixed installations - D.C. switchgear - Part 4: Outdoor d.c. disconnectors, switch-disconnectors and earthing switches
EN 50123-4:2003/A1:2013

This part of EN 50123 specifies requirements for outdoor d.c. switch-disconnectors, disconnectors and earthing switches for use in outdoor fixed installations of traction systems.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50123-3:2003/A1:2014(Amendment)
Railway applications - Fixed installations - D.C. switchgear - Part 3: Indoor d.c. disconnectors, switch-disconnectors and earthing switches
EN 50123-3:2003/A1:2013

This part of EN 50123 specifies requirements for d.c. disconnectors, switch-disconnectors and earthing switches for use in indoor fixed installations of traction systems.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50152-1:2013/A1:2013(Amendment)
Railway applications - Fixed installations - Particular requirements for alternating current switchgear - Part 1: Circuit-breakers with nominal voltage above 1 kV
EN 50152-1:2012/A1:2013

This EN 50152-1 is applicable to single-pole and two-pole alternating current (a.c.) circuit-breakers which are:
- for indoor or outdoor fixed installations in tractions systems, and
- operated with an a.c. line voltage and frequency as specified in EN 50163.
NOTE 1 EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz. NOTE 2 As rails of a.c. traction systems are connected to earth and included in the return current path all phase to earth voltages will be within the tolerances as specified in EN 50163. Nevertheless phase to phase voltages are sometimes higher e.g. in autotransformer systems. This European Standard is also applicable to the operating devices of circuit-breakers and to their auxiliary   equipment. This European Standard does not address circuit-breakers with dependent manual operating mechanism. NOTE 3 It is impossible to specify a rated short-circuit making current for these circuit-breakers and it is likely that such dependent manual operation is not meeting safety considerations.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50152-2:2013(Main)
Railway applications - Fixed installations - Particular requirements for alternating current switchgear - Part 2: Disconnectors, earthing switches and switches with nominal voltage above 1 kV
EN 50152-2:2012

This European Standard is applicable to single-pole and two-pole alternating current (a.c.) disconnectors, earthing switches and switches which are:
- designed for indoor or outdoor fixed installations in tractions systems, and
- operated with an a.c. line voltage and frequency as specified in EN 50163.
NOTE 1 EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz. NOTE 2 As rails of a.c. traction systems are connected to earth and included in the return current path all phase to earth voltages will be within the tolerances as specified in EN 50163. Nevertheless phase to phase voltages are sometimes higher, e.g. in autotransformer systems. NOTE 3 The two poles of a switch can be connected in series to provide secure isolation (i.e. two breaks in series).

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50152-1:2013(Main)
Railway applications - Fixed installations - Particular requirements for alternating current switchgear - Part 1: Circuit-breakers with nominal voltage above 1 kV
EN 50152-1:2012

This EN 50152-1 is applicable to single-pole and two-pole alternating current (a.c.) circuit-breakers which are:
- for indoor or outdoor fixed installations in tractions systems, and
- operated with an a.c. line voltage and frequency as specified in EN 50163.
NOTE 1 EN 50163 specifies the a.c. traction systems 15 kV 16,7 Hz and 25 kV 50 Hz. NOTE 2 As rails of a.c. traction systems are connected to earth and included in the return current path all phase to earth voltages will be within the tolerances as specified in EN 50163. Nevertheless phase to phase voltages are sometimes higher e.g. in autotransformer systems. This European Standard is also applicable to the operating devices of circuit-breakers and to their auxiliary   equipment. This European Standard does not address circuit-breakers with dependent manual operating mechanism. NOTE 3 It is impossible to specify a rated short-circuit making current for these circuit-breakers and it is likely that such dependent manual operation is not meeting safety considerations.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day