SIST EN 13163:2013+A2:2017/oprA3:2018
(Amendment)Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification
Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification
DOW = DAV + 21 months
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation
Produits isolants thermiques pour le bâtiment - Produits manufacturés en polystyrène expansé (EPS) - Spécification
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandiranega polistirena (EPS) - Specifikacija
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13163:2013+A2:2017/oprA3:2018
01-november-2018
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandiranega polistirena
(EPS) - Specifikacija
Thermal insulation products for buildings - Factory made expanded polystyrene (EPS)
products - Specification
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem
Polystyrol (EPS) - Spezifikation
Produits isolants thermiques pour le bâtiment - Produits manufacturés en polystyrène
expansé (EPS) - Spécification
Ta slovenski standard je istoveten z: EN 13163:2012+A2:2016/prA3
ICS:
91.100.60 0DWHULDOL]DWRSORWQRLQ Thermal and sound insulating
]YRþQRL]RODFLMR materials
SIST EN en,fr,de
13163:2013+A2:2017/oprA3:2018
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
---------------------- Page: 2 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
DRAFT
EUROPEAN STANDARD
EN 13163:2012+A2:2016
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA3
September 2018
ICS 91.100.60
English Version
Thermal insulation products for buildings - Factory made
expanded polystyrene (EPS) products - Specification
Produits isolants thermiques pour le bâtiment - Wärmedämmstoffe für Gebäude - Werkmäßig
Produits manufacturés en polystyrène expansé (EPS) - hergestellte Produkte aus expandiertem Polystyrol
Spécification (EPS) - Spezifikation
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 88.
This draft amendment A3, if approved, will modify the European Standard EN 13163:2012+A2:2016. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13163:2012+A2:2016/prA3:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
EN 13163:2012+A2:2016/prA3:2018 (E)
Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to the Scope . 4
3 Modification to Clause 2, "Normative references" . 4
4 Modification to Clause 3 "Terms, definitions, symbols, units and abbreviated terms" . 5
5 Modification to Clause 4, "Requirements" . 5
6 Modification to 4.1, "General" . 5
7 Modifications to 4.3, "For specific applications" . 5
8 Modification to 5.3.2, "Thermal resistance and thermal conductivity" . 6
9 Modification to Clause 6, "Designation code" . 7
10 Modification to Clause 7, "Assessment and Verification of the Constancy of
Performance (AVCP)" . 8
11 Modification to Clause 8, "Marking and labelling" . 8
12 Modification to Annex B, "Product type determination (PTD) and factory production
control (FPC)" . 8
13 Modification to Annex D, "Multi layered EPS products" . 14
14 Modification to Annex E, "Verification of the reaction to fire classification of raw
materials" . 14
15 Modification to Annex F, "Additional properties" . 14
16 Modification to the Annex ZA, "Clauses of this European Standard addressing the
provisions of the EU Construction Products Regulation" . 14
2
---------------------- Page: 4 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
EN 13163:2012+A2:2016/prA3:2018 (E)
European foreword
This document (EN 13163:2012+A2:2016/prA3:2018) has been prepared by Technical Committee
CEN/TC 88 "Thermal insulating materials and products", the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association.
For relationship with Regulation (EU) No. 305/2011, see informative Annex ZA, which is an integral
part of this document.
3
---------------------- Page: 5 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
EN 13163:2012+A2:2016/prA3:2018 (E)
1 Modification to the European foreword
In the fourth paragraph, delete the text ", and supports essential requirements of the EU Construction
Products Regulation (CPR).".
Replace the fifth paragraph with the following: "For relationship with Regulation (EU) No. 305/2011, see
informative Annex ZA, which is an integral part of this standard.".
Delete the ninth paragraph (list of changes) and replace the tenth paragraph with the following:
"Amendment A3 modifies EN 13163:2012 and its A1 and A2 amendments. The amendment introduces
or corrects:
a) Deletion of clause 4.3.18 Continuous glowing combustion;
b) Modification of clause 4.3.19 Release of Dangerous substances;
c) Modification of the definition for "class F" in the clause "reaction to fire";
d) Editorial modifications in different parts of the text and linked to the above modifications;
e) Addition in Table 9 to clarify testing of complicated shapes;
f) Modifications to be in line with the CPR e.g. PTD replaced by TT;
g) Change the reference Directive to Regulation;
h) Change the word Requirement to Characteristic for those sentences in which the text deals with a
Requirement/Characteristic in terms of the CPR;
i) Modification of Annex ZA.".
Delete the eleventh paragraph (additional list of changes).
In the fourteenth paragraph, add the following standard to the end of the list of standards:
"EN 16069, Thermal insulation products for buildings — Factory made products of polyethylene foam
(PEF) — Specification".
2 Modification to the Scope
Replace the first sentence with:
"This European Standard specifies the characteristics for factory made expanded polystyrene products,
with or without rigid or flexible facings or coatings, which are used for the thermal insulation of
buildings.".
Replace the third paragraph with:
"This standard describes product characteristics and includes procedures for testing, assessment and
verification of constancy of performance (AVCP), marking and labelling.".
3 Modification to Clause 2, "Normative references"
Add the following reference:
"EN 16516, Construction products — Assessment of release of dangerous substances — Determination of
emissions into indoor air"
4
---------------------- Page: 6 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
EN 13163:2012+A2:2016/prA3:2018 (E)
4 Modification to Clause 3 "Terms, definitions, symbols, units and abbreviated
terms"
In 3.1, delete the term and definition for "3.1.6 level" and "3.1.7 class" and modify the numbers of the
following terms accordingly.
In 3.2, delete the following abbreviated terms:
PTD is Product Type Determination (previously named ITT for Initial Type Test)
VCP is Verification of Constancy of Performance (previously named evaluation of conformity)
Please add the following abbreviated term:
"
TT is Type Testing
".
5 Modification to Clause 4, "Requirements"
In the title of the clause, replace "Requirements" with "Characteristics".
6 Modification to 4.1, "General"
Replace the text in the clause with the following:
"Product characteristics shall be assessed in accordance with Clause 5. To comply with this standard,
products shall meet the characteristics of 4.2 and the characteristics of 4.3, as appropriate.
NOTE Information on additional characteristics is given in Annex F.
For multi-layered products, additional characteristics are given in Annex D.
One test result for a product characteristic is the average of the measured values on the number of test
specimens given in Table 9.".
7 Modifications to 4.3, "For specific applications"
In 4.3.1, replace the text in the clause with the following:
"If there is no requirement for a characteristic described in 4.3 for a product in use, then the
characteristic does not need to be determined and declared by the manufacturer.".
In 4.3.4, replace the last sentence of the clause with:
"If EPS products are classified according to Table C.1, the products shall fulfil the characteristics of
bending strength given in Table C.1.".
Delete subclause 4.3.18.
In 4.3.19, renumber as "4.3.18" and replace the text in the clause with the following:
1)
"If the release of dangerous substances into indoor air is tested, this shall be done according to
EN 16516.
NOTE An informative database covering European and national provisions on dangerous substances is
available at the Construction web site on EUROPA accessed through: http://ec.europa.eu/growth/tools-
databases/cp-ds.".
1) See for reference the LCI list of the European Commission "Agreed EU-LCI values"
(http://ec.europa.eu/growth/sectors/construction/eu-lci/values_en).
5
---------------------- Page: 7 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
EN 13163:2012+A2:2016/prA3:2018 (E)
8 Modification to 5.3.2, "Thermal resistance and thermal conductivity"
Replace Table 9 with the following new table:
"Table 9 — Test methods, test specimens and conditions
Clause Test specimen
Minimum
Length and number of
Test
Specific
a,h
width measurements
conditions
method
No Title
to get one test
Dimensions in
result
millimetres
b
Thermal conductivity and See EN 12667 1 –
4.2.1 EN 12667
thermal resistance
or
or EN 12939
EN 12939
Length and width Full-size 1 –
4.2.2 EN 822
Thickness Full-size 1 Load of
4.2.3 EN 823
(250 ± 5) Pa
Squareness Full-size 1 –
4.2.4 EN 824
4.3.3
Flatness Full-size 1 –
4.2.5 EN 825
Reaction to fire of the See EN 13501-1 and EN 15715 See
4.2.6
product as placed on the EN 15715:2009,
market Clause 5
Dimensional stability under 500 x 500 x d 3 Method B1
4.3.2 EN 1603
constant normal laboratory
conditions
Dimensional stability under 200 × 200 x d 3 –
4.3.2 EN 1604
specified temperature and
humidity conditions
c
Compressive stress at 10 % 50 × 50 × d 5 Grinding
4.3.4 EN 826
deformation
d d d
l * b *d 3
d
Bending strength 300 ×150 × 50 3 Method B
4.3.5 EN 12089
or
(5 × d + 50) ×
e
150 × d
c
Tensile strength 50 × 50 × d 5 –
4.3.6 EN 1607
perpendicular to faces
d d d
l * b *d 3
c
Deformation under specified 50 × 50 × d 5 Layers or
4.3.7 EN 1605
compressive load and coverings have
d d d
l * b *d 3
temperature conditions to be cut off
c f
Compressive creep 50 × 50 × 50 2 Grinding
4.3.8 EN 1606
g
Shear behaviour 50 x 250 x d 5 or Single test
4.3.9 EN 12090
specimen
3 Double test
specimen
4.3.10 Dynamic load resistance EN 13793 150 x 150 x d 1 -
4.3.11.1 Long term water absorption EN 12087 200 x 200 x d 3 Total immersion:
by immersion Method 2A
6
---------------------- Page: 8 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
EN 13163:2012+A2:2016/prA3:2018 (E)
Clause Test specimen
Minimum
Length and number of
Test
Specific
a,h
width measurements
conditions
method
No Title
to get one test
Dimensions in
result
millimetres
4.3.11.2 Long term water absorption EN 12088 500 × 500 x d 2 –
by diffusion
4.3.12 Freeze-thaw resistance EN 12091 500 × 500 x d 3 Preparation by
EN 12087,
method 2A or
EN 12088
4.3.13 Water vapour transmission EN 12086 See 5 Set B
EN 12086:1997,
6.1
4.3.14 Dynamic stiffness EN 29052- 200 × 200 x d 3 –
1
4.3.15.2 Thickness, dL EN 12431 200 × 200 x d 3 –
4.3.15.3
Thickness, dB EN 12431 Measure 300 s
4.3.15.4
after the preload
has been
removed
Long term thickness EN 1606 –
reduction
4.3.16 Apparent density EN 1602 Full-size 5 –
4.3.17 Reaction to fire of the See EN 13501-1 and EN 15715 See
product in standardises EN 15715:2009,
assemblies simulating end- Clause 6
use applications
4.3.18 Release of dangerous EN 16516 See EN 16516 See EN 16516 See 4.3.18
substances
a
Test specimen dimensions shall be determined in accordance with EN 12085.
b
For calculation of the 90 % fractile and 90 % confidence level, the individual measurement shall be used.
c
Sample size with thickness d < 50 mm.
d
Sample size used for boards ≥ 50 mm.
e
For boards of thickness d < 50 mm and shape moulded products.
f
The specimens shall have the same thickness and shall not deviate in density more than 1,5 kg/m³.
g
Maximum thickness 50 mm.
h
For complicated shapes mechanical test and tests on thermal conductivity, samples will be made plan parallel, for
other tests the original shape will be tested. Any difference from the dimensions of the original product must be
reported.
".
9 Modification to Clause 6, "Designation code"
Replace the first paragraph with the following:
"If a designation code is provided, it shall be given as follows: The following shall be included except
when there is no requirement for a characteristic described in 4.3:".
7
---------------------- Page: 9 ----------------------
SIST EN 13163:2013+A2:2017/oprA3:2018
EN 13163:2012+A2:2016/prA3:2018 (E)
10 Modification to Clause 7, "Assessment and Verification of the Constancy of
Performance (AVCP)"
Replace the subclauses with the following:
"7.1 General
The manufacturer or his authorized representative shall be responsible for the conformity of his
product with the characteristics of this European Standard. The Assessment and Verification of
Constancy of Performance (AVCP) shall be carried out in accordance with EN 13172 and shall be based
on Type Testing (TT), Factory Production Control (FPC) by the manufacturer, including product
assessment and tests on samples taken at the factory.
The compliance of the product with the characteristics of this standard and with the stated values
(including classes) shall be demonstrated by:
— Type Testing (TT),
— Factory Production Control (FPC) by the manufacturer, including product assessment.
If a manufacturer decides to group his products, it shall be done in accordance with EN 13172.
7.2 Type Testing (TT)
All characteristics defined in 4.2 and those in 4.3 if declared, shall be subject to Type Testing (TT) in
accordance with Annex B.
For the relevant characteristics, TT on products corresponding also to EN 13499, EN 14309, EN 14933
and EN 15037-4 may be used for the purpose of TT and Declaration of Performance (DoP) according to
this standard.
7.3 Factory Production Control (FPC)
The manufacturer shall establish, document and maintain an FPC system to ensure that the products
placed on the market comply with the declared performance of the essential characteristics.
The minimum frequencies of tests in the factory production control (FPC) shall be in accordance with
Annex B of this standard. When indirect testing is used, the correlation to direct testing shall be
established in accordance with EN 13172.
For the relevant characteristics, FPC on products corresponding also to EN 13499, EN 14309, EN 14933
and EN 15037-4 may be used for the purpose of FPC and DoP according to this standard.
7.4 Initial inspection
The initial inspection of the factory and of FPC shall be done in accordance with EN 13172.
7.5 Continuous surveillance
The continuous surveillance of FPC shall be done in accordance with EN 13172.".
11 Modification to Clause 8, "Mar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.