SIST EN ISO 21269:2004
(Main)Hexagon socket head cap screws with metric fine pitch thread (ISO 21269:2004)
Hexagon socket head cap screws with metric fine pitch thread (ISO 21269:2004)
Zylinderschrauben mit Innensechskant mit metrischem Feingewinde (ISO 21269:2004)
Diese Internationale Norm legt die Eigenschaften von Zylinderschrauben mit Innensechskant mit metrischem Feingewinde, mit Gewindenenndurchmessern, d von 8 mm bis 64 mm und mit Produktklasse A fest.
Angaben über die ungefähren Gewichte enthält Anhang A.
Werden in besonderen Fällen andere Festlegungen als die in der vorliegenden Internationalen Norm benötigt, so sollten diese den bestehenden Internationalen Normen entnommen werden, z. B. ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 3506-1, ISO 8839 und ISO 4759-1.
Vis a tete cylindrique a six pans creux a pas fin (ISO 21269:2004)
Vijaki z valjasto glavo in notranjim šestkotnikom, z drobnim metrskim navojem (ISO 21269:2004)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Vijaki z valjasto glavo in notranjim šestkotnikom, z drobnim metrskim navojem (ISO 21269:2004)Zylinderschrauben mit Innensechskant mit metrischem Feingewinde (ISO 21269:2004)Vis a tete cylindrique a six pans creux a pas fin (ISO 21269:2004)Hexagon socket head cap screws with metric fine pitch thread (ISO 21269:2004)21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studs21.040.10Metrski navojiMetric screw threadsICS:Ta slovenski standard je istoveten z:EN ISO 21269:2004SIST EN ISO 21269:2004en01-september-2004SIST EN ISO 21269:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 21269March 2004ICS 21.060.10English versionHexagon socket head cap screws with metric fine pitch thread(ISO 21269:2004)Vis à tête cylindrique à six pans creux à pas fin (ISO21269:2004)Zylinderschrauben mit Innensechskant mit metrischemFeingewinde (ISO 21269:2004)This European Standard was approved by CEN on 9 January 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 21269:2004 ESIST EN ISO 21269:2004
INTERNATIONALSTANDARDISO21269First edition2004-03-01Reference numberISO21269:2004(E)© ISO2004Hexagon socket head cap screws with metric fine pitch threadVis à tête cylindrique à six pans creux à pas fin
ISO21269:2004(E)ii© ISO2004–All rights reservedPDF disclaimerThis PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shallnot be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Indownloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariataccepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creationparameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In theunlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.©ISO2004All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below orISO's member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel.+ 41 22 749 01 11Fax+ 41 22 749 09 47E-mailcopyright@iso.orgWebwww.iso.orgPublished in SwitzerlandSIST EN ISO 21269:2004
ISO21269:2004(E)© ISO2004–All rights reservediiiContents Page1Scope . 12Normative references . 13Dimensions . 24Requirements and reference International Standards . 65Designation . 6AnnexA(informative)Masses . 7SIST EN ISO 21269:2004
ISO21269:2004(E)iv© ISO2004–All rights reservedForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the InternationalElectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part2.The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75% of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.ISO21269 was prepared by Technical Committee ISO/TC2, Fasteners.SIST EN ISO 21269:2004
INTERNATIONAL STANDARDISO21269:2004(E)© ISO2004–All rights reserved1Hexagon socket head cap screws with metric fine pitch thread1ScopeThis International Standard specifies the characteristics of hexagon socket head cap screws with metric finepitch thread with nominal thread diameters, , from
up to
and product gradeA.For approximate masses of screws see AnnexA.If, in special cases, specifications other than those listed in this International Standard are required, they shouldbe selected from existing International Standards, e.g. ISO261, ISO888, ISO898-1, ISO965-2, ISO3506-1,ISO8839 and ISO4759-1.2Normative referencesThe following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenced document(including any amendments) applies.ISO225, Fasteners— Bolts, screws, studs and nuts— Symbols and designations of dimensionsISO261, ISO general-purpose metric scre
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.