49.080 - Aerospace fluid systems and components

This document defines the requirements of ethylene propylene elastomer (EPM/EPDM) for seal elements for use as static seals in hydraulic systems using phosphate ester fluids, hardness 80 IRHD (International Rubber Hardness Degree) for long term application for aerospace application.
Unless otherwise specified in the drawing, order or inspection schedule, this document shall be used in conjunction with the referenced documents.
Applicable temperature range:
- Continuous service: −55 °C to 107 ...view more

This document specifies the dimensions, tolerances and required characteristics of protective plugs,
non-metallic, for NAS1760 fitting ends and AS33649 boss ports to seal fluid ports during transportation
and storage in order to prevent
 contamination by moisture, fluids, chemicals and particles,
 spillage inside package or aircraft section,
 port and pipe end damages and
 port and pipe clogging due to plug ingestion.
Because of the cleanliness requirements, parts shall only be used o...view more

This document specifies the dimensions, tolerances and required characteristics of protective plugs, non metallic, for EN 6123 fitting ends to seal fluid ports during transportation and storage in order to prevent:
- contamination by moisture, fluids, chemicals and particles;
- spillage inside package or aircraft section;
- port and pipe end damages;
- port and pipe clogging due to plug ingestion.
Because of the cleanliness requirements, parts shall only be used once.

This document specifies the dimensions, tolerances and required characteristics of protective caps, non metallic, for EN 6123 fitting ends to seal fluid ports during transportation and storage in order to prevent:
- contamination by moisture, fluids, chemicals and particles;
- spillage inside package or aircraft section;
- port and pipe end damages;
- port and pipe clogging due to plug ingestion.
Because of the cleanliness requirements, parts shall only be used once.

This document specifies the dimensions of connections for starting aircraft engines by air, which are necessary to ensure international interchangeability of connectors with adaptors. lt also gives the minimum clearances required on the aircraft to provide adequate access for the ground adaptor.

This document specifies characteristics of hose assemblies with corrosion‑resistant metallic braid and convoluted polytetrafluoroethylene (PTFE) inner tube for use in aircraft fluid systems at temperatures between ‑55 °C and +200 °C and at nominal pressures, depending on bore size, up to 6,8 MPa. Special approval from the proper national authority can be required if these hoses are to be part of a pressurized gas storage system. Two types of hose assembly are covered in this document: — Type 1: ...view more

This document establishes the general requirements for a linear hydraulic utility actuator, herein referred to as a "utility actuator", for use in flight vehicle hydraulic systems at pressures up to 35 000 kPa (5 000 psi). These requirements include: — design requirements; — test requirements. This document is intended to be used in conjunction with the detail specification that is particular to each application. NOTE Although Brake pistons and Landing Gear Bogie (Truck) Pitch Trimmers are utili...view more

This European standard specifies the designation method for hose assemblies within 15 digits.

This European standard specifies the designation method for hose assemblies within 15 digits.

This European standard specifies the required characteristics, inspection and test methods, quality
assurance and procurement requirements for metric series 8°30’ dynamic beam seal pipe couplings, for
temperature ranges type II and III according to ISO 6771 and nominal pressure up to 28 000 kPa.

This European standard specifies the required characteristics, inspection and test methods, quality
assurance and procurement requirements for metric series 8°30’ dynamic beam seal pipe couplings, for
temperature ranges type II and III according to ISO 6771 and nominal pressure up to 28 000 kPa.

This document establishes the general requirements for constant displacement hydraulic motors, suitable for use in aircraft hydraulic systems at pressures up to 35 000 kPa (5 000 psi). Primary and secondary function motors (see Clause 4) are covered in this document; however, actuators with internal rotation angle limits and low-speed motors are not covered. This document is to be used in conjunction with the detail specification that is particular to each application.

This European Standard defines the requirements for moulded elastomer seal elements for use in hydraulic systems using phosphate ester fluids for aerospace application. It shall be applied in conjunction with relevant material standards unless otherwise specified on the drawing, order, inspection schedule or contractual document.

This European Standard specifies the dimensions, tolerances and the required characteristics of a fitting end, 24° cone, external thread, flareless type, size −32 for use in hydraulic and fluid systems at 220 psi, diameter D = 2 inches (D = 50,8 mm) for aerospace applications.
This is a design standard, not valid for order.
This fitting can not be used for plug in union.

This standard specifies the dimensions, tolerances, required characteristics and the mass of an adaptor, flareless tube end EN 6123, ring locked type, for use in 35 000 kPa (5 080 psi) working pressure systems.

This European Standard specifies the dimensions, tolerances, required characteristics and the mass of a reducer, flareless tube end EN 6123, ring locked type, for use in 35 000 kPa (5 080 psi) working pressure systems.

This European Standard specifies the installation and removal requirements for adaptors and
reducers, threaded, with lockring for pipe couplings 24° according to EN 4833 and EN 4836.
This standard establishes an accurate procedure of adaptor installation, removal and reinstallation to
ensure the repeatability of the installation operation and to ensure the effective compliance to sealing
and locking requirements.
The adaptor shown on all Figures of this standard is given as an example for t...view more

This standard specifies the characteristics of the pipe coupling adapter, 60° spherical sealing face manufactured in titanium alloy with locking ring, for installing in a boss for aerospace applications.
These adapters shall be installed into port connections manufactured in accordance with EN 2602 using ISO 3601-1 sealing O-rings selected sizes. O-ring material depends on the system fluid and operation conditions. The installation shall be performed in accordance with EN 2608.
Nominal working...view more

This standard specifies the dimensions, tolerances and requirements of a port for a fluid connection with ring locked fitting, for use in aircraft systems at nominal operating pressure of 35 000 kPa (5 080 psi) maximum and temperature range of −54 to +135 °C (−65 to +275 °F).

This specification establishes the requirements for ring locked fitting assemblies according to EN 4833
and EN 4836, for use in aircraft systems at nominal operating pressure of 35 000 kPa (5 080 psi)
maximum and temperature range of −54 °C to +135 °C (−65 °F to +275 °F).