Aerospace series - Ethylene-propylene elastomer (EPM/EPDM) - Hardness 80 IRHD for static seal elements in hydraulic systems for long-term application - Material standard

This document defines the requirements of ethylene propylene elastomer (EPM/EPDM) for seal elements for use as static seals in hydraulic systems using phosphate ester fluids, hardness 80 IRHD (International Rubber Hardness Degree) for long term application for aerospace application.
Unless otherwise specified in the drawing, order or inspection schedule, this document shall be used in conjunction with the referenced documents.
Applicable temperature range:
- Continuous service: −55 °C to 107 °C
- Intermittent service: −55 °C to 120 °C

Luft- und Raumfahrt - Ethylen-Propylen-Elastomer (EPM/EPDM) - Härte 80 IRHD für statische Dichtungen in Hydraulik-Systemen für Langzeitanwendung - Werkstoffnorm

Dieses Dokument legt die Anforderungen an Ethylen Propylen Elastomer (EPM/EPDM) der Härte 80 IRHD (International Rubber Hardness Degree) für Dichtungselemente zur Langzeitverwendung als statische Dichtungen in Hydrauliksystemen mit Phosphorsäureesterflüssigkeiten in der Luft  und Raumfahrt fest.
Falls nicht anders in der Zeichnung, Bestellung oder Prüfanweisung festgelegt, ist dieses Dokument zusammen mit den in Bezug genommenen Dokumenten zu verwenden.
Anzuwendender Temperaturbereich:
- Dauerbetrieb: −55 °C bis 107 °C;
- Aussetzbetrieb: −55 °C bis 120 °C.

Série aérospatiale - Élastomère éthylène propylène (EPM/EPDM) - Dureté 80 IRDH pour joints statiques en systèmes hydrauliques pour application à long terme - Norme de matériau

Le présent document définit les exigences de l’élastomère éthylène propylène (EPM/EPDM) pour les éléments d’étanchéité destinés à être utilisés en tant que joints statiques dans les systèmes hydrauliques utilisant des fluides esterphosphoriques, de dureté 80 DIDC (degrés internationaux de dureté du caoutchouc), pour usage à long terme dans les applications aérospatiales.
Sauf spécification contraire dans le dessin, la commande ou le calendrier d’inspection, ce document doit être utilisé conjointement avec les documents cités en référence.
Plage de températures applicable :
- service continu : −55 °C à 107 °C ;
- service intermittent : −55 °C à 120 °C.

Aeronavtika - Etilen-propilen elastomer (EPM/EPDM) - Trdota 80 IRHD za statične tesnilne elemente v hidravličnih sistemih za dolgotrajno uporabo - Standardi za materiale

General Information

Status
Published
Publication Date
14-Oct-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
08-Oct-2020
Due Date
13-Dec-2020
Completion Date
15-Oct-2020

Buy Standard

Standard
SIST EN 6111:2020
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 6111:2020
01-december-2020
Aeronavtika - Etilen-propilen elastomer (EPM/EPDM) - Trdota 80 IRHD za statične
tesnilne elemente v hidravličnih sistemih za dolgotrajno uporabo - Standardi za
materiale

Aerospace series - Ethylene-propylene elastomer (EPM/EPDM) - Hardness 80 IRHD for

static seal elements in hydraulic systems for long-term application - Material standard

Luft- und Raumfahrt - Ethylen-Propylen-Elastomer (EPM/EPDM) - Härte 80 IRHD für
statische Dichtungen in Hydraulik-Systemen für Langzeitanwendung - Werkstoffnorm

Série aérospatiale - Élastomère éthylène propylène (EPM/EPDM) - Dureté 80 IRDH pour

joints statiques en systèmes hydrauliques pour application à long terme - Norme de

matériau
Ta slovenski standard je istoveten z: EN 6111:2020
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
49.080 Letalski in vesoljski Aerospace fluid systems and
hidravlični sistemi in deli components
SIST EN 6111:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 6111:2020
---------------------- Page: 2 ----------------------
SIST EN 6111:2020
EN 6111
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 49.025.40; 49.080
English Version
Aerospace series - Ethylene-propylene elastomer
(EPM/EPDM) - Hardness 80 IRHD for static seal elements
in hydraulic systems for long-term application - Material
standard

Série aérospatiale - Élastomère éthylène propylène Luft- und Raumfahrt - Ethylen-Propylen-Elastomer

(EPM/EPDM) - Dureté 80 DIDC pour joints statiques (EPM/EPDM) - Härte 80 IRHD für statische Dichtungen

dans les systèmes hydrauliques pour application à long in Hydraulik-Systemen für Langzeitanwendung -

terme - Norme de matériau Werkstoffnorm
This European Standard was approved by CEN on 22 December 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6111:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 6111:2020
EN 6111:2020 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 5

4 Requirements ................................................................................................................................................... 5

4.1 General ................................................................................................................................................................ 5

4.2 Specific ................................................................................................................................................................ 5

4.2.1 Physical and mechanical requirements .................................................................................................. 5

4.2.2 Test specimens ................................................................................................................................................. 5

4.2.3 Hazardous constituents ................................................................................................................................ 5

5 Designation........................................................................................................................................................ 5

6 Technical specification .................................................................................................................................. 6

---------------------- Page: 4 ----------------------
SIST EN 6111:2020
EN 6111:2020 (E)
European foreword

This document (EN 6111:2020) has been prepared by the Aerospace and Defence Industries

Association of Europe - Standardization (ASD-STAN).

After enquiries and votes carried out in accordance with the rules of this Association, this Standard has

received the approval of the National Associations and the Official Services of the member countries of

ASD, prior to its presentation to CEN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall

be withdrawn at the latest by March 2021.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
---------------------- Page: 5 ----------------------
SIST EN 6111:2020
EN 6111:2020 (E)
1 Scope
This document d
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.