iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D267-82(2008)e1

(Specification)

Standard Specification for Gold Bronze Powder

Standard Specification for Gold Bronze Powder

ABSTRACT
This specification covers the materials commercially known as gold bronze, pale gold bronze, and rich gold bronze powders. The gold bronze powder shall be made from new ingot metals, shall consist of fine polished flakes containing the prescribed percentage of fatty or oily matter (polishing lubricant), shall have the specified residue content and leafing properties, and shall be suitable for making gold bronze paint. The sampling and test methods to determine conformance to the specified composition and properties are given.
SCOPE
1.1 This specification covers the materials commercially known as gold bronze, pale gold bronze, and rich gold bronze powders.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

General Information

Status
Historical
Publication Date
30-Jun-2008
ICS
87.060.99 - Other paint ingredients
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.31 - Pigment Specifications
Current Stage
Ref Project

Relations

Replaces
ASTM D267-82(2003) - Standard Specification for Gold Bronze Powder
Effective Date
01-Jul-2008
Replaced By
ASTM D267-82(2014) - Standard Specification for Gold Bronze Powder
Effective Date
01-Dec-2014

Buy Standard

ASTM D267-82(2008)e1 - Standard Specification for Gold Bronze PowderASTM D267-82(2008)e1 - Standard Specification for Gold Bronze Powder
PreviousNext
Technical specification
ASTM D267-82(2008)e1 - Standard Specification for Gold Bronze Powder
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:D267 −82(Reapproved 2008)
Standard Specification for
Gold Bronze Powder
This standard is issued under the fixed designation D267; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
ε NOTE—The units statement in subsection 1.2 was corrected editorially in July 2008.
1. Scope 3.3 The powder shall have good “leafing” properties. (By
“leafing” is understood the property of forming an apparently
1.1 This specification covers the materials commercially
continuous brilliant film over the entire free surface of a
known as gold bronze, pale gold bronze, and rich gold bronze
mixture of the powder in a suitable liquid (Note 1), within 1
powders.
min after cessation of stirring the mixture.) In testing for
1.2 The values stated in inch-pound units are to be regarded
leafing properties the powder shall be mixed in the proportion
as standard. The values given in parentheses are mathematical
of 3 to 4 lb (370 to 475 g/L) to a gallon (3.8 L) of the liquid.
conversions to SI units that are provided for information only
As thus mixed it shall also give a free flowing, smooth,
and are not considered standard.
continuous coating in accordance with Test Methods D480.
2. Referenced Documents NOTE 1—A suitable liquid is made by mixing spar varnish conforming
to the U. S. Federal Specification for Water-Resisting Spar Varnish (No.
2.1 ASTM Standards:
A-A-1800) with turpentine conforming to Specification D13 in such
D13 Specification for Spirits of Turpentine
proportions that the mixture will have a viscosity of 0.65 to 0.85 poises (B
to C on the Gardner-Holdt scale).
D185 Test Methods for Coarse Particles in Pigments
D480 Test Methods for Sampling and Testing of Flaked
3.4 The gold bronze powder shall be suitable for making
Aluminum Powders and Pastes
gold bronze paint. It shall match in shade and fineness a
2.2 U.S. Federal Specification:
reference sample mutually agreed upon by the purchaser and
A-A-1800 Water-Resisting Spar Varnish
the seller.
3. Composition and Properties
4. Sampling
3.1 The bronze powder shall be made from new ingot
4.1 Two samples shall be taken at random from different
metals. It shall consist of fine polished flakes containing not
packages from each lot, batch, day’s pack, or other unit of
less than 3 % of fatty or oily matter (polishing lubricant) to
production in a shipment. When no markings distinguishing
give good “leafing” properties.
between units of production appear, samples shall be taken
from different packages in the ratio of two samples for each 5
3.2 The residue retained on a No. 100 (150-µm) sieve, using
tons (inch-pound or SI), except that for shipments of less than
alcohol as
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D564-87(2023)(Test Method)
Standard Test Methods for Liquid Paint Driers

SIGNIFICANCE AND USE
3.1 Driers accelerate the drying of oil, paint, printing ink, and varnish.  
3.2 These test methods are applicable to liquid driers manufactured for use in paints and related coatings.  
3.3 The tests for metallic content using ethylenediaminetetraacetic acid dihydrate (EDTA) are intended for concentrated solutions of single metals; two or more metals may cause interference.
SCOPE
1.1 These test methods cover the test procedures to be applied to liquid paint driers used in paints and related coatings. Typical paint driers, listed in Specification D600, are carboxylates of lead, cobalt, manganese, zinc, iron, calcium, and zirconium.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3970-05(2023)(Test Method)
Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm in the presence of rare earths the stated cerium content of liquid pure cerium or rare earth driers manufactured for use in the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of cerium in liquid cerium and rare earth paint driers and utilizes ferrous ammonium sulfate.  
1.2 This test method is not applicable to dryer blends.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 7.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3988-05(2023)(Test Method)
Standard Test Method for Vanadium in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated content of a pure liquid vanadium drier manufactured for use by the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of vanadium in liquid vanadium driers and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the vanadium content of a liquid vanadium drier that does not contain other drier elements. This test method is not applicable to drier blends.  
1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.  
1.4 This test method has been tested for concentrations of 3 % and 4 % vanadium, but there is no reason to believe that it is not suitable for higher or lower vanadium concentrations provided specimen size is adjusted proportionately.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2613-01(2023)(Test Method)
Standard Test Method for Calcium or Zinc in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated calcium or zinc content of pure liquid calcium or zinc driers soluble in toluene-alcohol and manufactured for use by the coatings industry.
SCOPE
1.1 This test method covers a titrimetric determination of calcium in liquid calcium driers and zinc in liquid zinc driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is not applicable to drier blends.  
1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3804-02(2021)(Test Method)
Standard Test Method for Iron in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated content of a liquid iron drier soluble in isopropyl alcohol and manufactured for use in the coatings industry. The content determines activity level.
SCOPE
1.1 This test method covers the titrimetric determination of iron in liquid iron driers soluble in isopropyl alcohol and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the iron content of a liquid drier that does not contain other drier elements. This method is not applicable to drier blends.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D267-82(2020)(Specification)
Standard Specification for Gold Bronze Powder

ABSTRACT
This specification covers the materials commercially known as gold bronze, pale gold bronze, and rich gold bronze powders. The gold bronze powder shall be made from new ingot metals, shall consist of fine polished flakes containing the prescribed percentage of fatty or oily matter (polishing lubricant), shall have the specified residue content and leafing properties, and shall be suitable for making gold bronze paint. The sampling and test methods to determine conformance to the specified composition and properties are given.
SCOPE
1.1 This specification covers the materials commercially known as gold bronze, pale gold bronze, and rich gold bronze powders.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D964-03(2020)(Specification)
Standard Specification for Metallic Copper Powder for Use in Antifouling Paints

ABSTRACT
This specification covers metallic copper powder for use in antifouling paints. The pigment shall consist essentially of finely divided copper metal. The copper, and coarse particle shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers copper powder for use in antifouling paints.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    1 page
    English language
    sale 15% off
ASTM
ASTM D3969-01(2019)e1(Test Method)
Standard Test Method for Zirconium in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 The amount of zirconium drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated content of a pure liquid zirconium drier manufactured for use by the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of zirconium in zirconium driers used in the coatings industry and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the zirconium content of a liquid zirconium drier that does not contain other drier elements. The test method is not applicable to drier blends and does not differentiate hafnium from zirconium.  
1.3 All cations that can be titrated with EDTA in acid media interfere and must not be present in the sample.  
1.4 This test method has been tested for concentrations of 6 and 12 % zirconium, but there is no reason to believe that it is not suitable for higher or lower zirconium concentrations, provided specimen size is adjusted proportionately.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3989-01(2019)e1(Test Method)
Standard Test Method for Total Rare Earth Metals in Paint Driers by EDTA Method

SIGNIFICANCE AND USE
4.1 This test method may be used to confirm the stated content of a pure, liquid rare earth metal drier manufactured for use in the coatings industry.
SCOPE
1.1 This test method covers the titrimetric determination of rare earth metals in liquid rare earth metal driers and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).  
1.2 This test method is limited to the determination of the rare earth metal content of a liquid rare earth metal drier that does not contain other drier elements. The method is not applicable to drier blends.  
1.3 This test method has been tested in concentrations of 6 % cerium and 6 % rare earth metals, but there is no reason to believe that it is not suitable for higher or lower drier metal concentrations provided specimen size is adjusted accordingly.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4140-07(2018)(Guide)
Standard Guide for Determining Volatile and Nonvolatile Content of Driers, Drying Oils, Naval Stores, and Solvents

SIGNIFICANCE AND USE
4.1 The nonvolatile content of raw materials may be used to determine the total nonvolatile content (solids) of paint and related coatings. Such information may be useful to coatings producers and users for the determination of the total solids available for film formation and for the estimation of the volatile organic content.
SCOPE
1.1 This guide is intended to aid in the selection of the proper ASTM test method for determining the volatile and nonvolatile content of driers, drying oils, naval stores, and solvents.  
Note 1: Test methods for determining the composition of the volatile fraction are not covered by this guide.  
1.2 The test methods included are as follows:    
Standard  
Section  
ASTM Designation  
Driers  
5.1  
D1644  
Drying oils  
5.2  
D555
D1960  
Naval stores  
5.3  
D233
D889
D1131  
Solvents  
5.4  
D1353  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off