ASTM F1173-01

Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications

SCOPE
1.1 This specification covers reinforced thermosetting resin pipe systems with nominal pipe sizes (NPS) 1 through 48 in. (25 through 1200 mm) which are to be used for all fluids approved by the authority having jurisdiction in marine piping systems.
1.2 Values stated in inch-pound are to be regarded as the standard. Values given in parentheses are for information only.
1.3 The dimensionless designator NPS has been substituted for traditional terms as "nominal diameter," "size," and "nominal size."
1.4 The following safety hazards caveat pertains to the test methods which are included in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Dec-2001
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.11 - Machinery and Piping Systems

Relations

• Replaces: ASTM F1173-95 - Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications
• Effective Date: 10-Dec-2001
• Replaced By: ASTM F1173-01(2006) - Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications
• Effective Date: 01-Feb-2006
• Referred By: ASTM D5677-17 - Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines
• Effective Date: 10-Dec-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1173 – 01
Standard Specification for
Thermosetting Resin Fiberglass Pipe Systems to Be Used
1
for Marine Applications
This standard is issued under the fixed designation F1173; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope D2924 Test Method for External Pressure Resistance of
“Fiberglass” (Glass-Fiber-Reinforced Thermosetting-
1.1 This specification covers reinforced thermosetting resin
3
Resin) Pipe
pipe systems with nominal pipe sizes (NPS) 1 through 48 in.
D2992 Practice for Obtaining Hydrostatic or Pressure De-
(25 through 1200 mm) which are to be used for all fluids
sign Basis for “Fiberglass” (Glass-Fiber-Reinforced
approved by the authority having jurisdiction in marine piping
3
Thermosetting-Resin) Pipe and Fittings
systems.
D3567 Practice for Determining Dimensions of “Fiber-
1.2 Values stated in inch-pound are to be regarded as the
glass”(Glass-Fiber-ReinforcedThermosetting-Resin)Pipe
standard.Values given in parentheses are for information only.
3
and Fittings
1.3 The dimensionless designator NPS has been substituted
D5028 Test Method for Curing Properties of Pultrusion
fortraditionaltermsas“nominaldiameter,”“size,”and“nomi-
5
Resins by Thermal Analysis
nal size.”
D 5686 Specification for “Fiberglass” (Glass-Fiber-
1.4 The following safety hazards caveat pertains to the test
Reinforced Thermosetting-Resin) Pipe and Pipe Fittings,
methodswhichareincludedinthisspecification. This standard
AdhesiveBondedJointTypeEpoxyResin,forCondensate
does not purport to address all of the safety concerns, if any,
3
Return Lines
associated with its use. It is the responsibility of the user of this
E1529 Test Methods for Determining Effects of Large
standard to establish appropriate safety and health practices
Hydrocarbon Pool Fires on Structural Members and As-
and determine the applicability of regulatory limitations prior
6
semblies
to use.
3
F412 Terminology Relating to Plastic Piping Systems
2. Referenced Documents 2.2 Other Documents:
7
ANSI B16.1 Cast Iron Pipe Flanges and Flanged Fittings
2.1 ASTM Standards:
7
2
ANSI B16.5 Pipe Flanges and Flanged Fittings
D883 Terminology Relating to Plastics
IMO Resolution A.753(18) Guidelines for the Application
D1598 Test Method for Time-To-Failure of Plastic Pipe
8
3
of Plastic Pipes on Ships
Under Constant Internal Pressure
9
NSF-61
D1599 Test Method for Resistance to Short-Time Hydrau-
3
Code of Federal Regulations 21CFR175.105,
lic Failure Pressure of Plastic Pipe, Tubing, and Fittings
8
21CFR177.2280, 21CFR177.2410, and 21CFR177.2420
D2105 Test Method for Longitudinal Tensile Properties of
Code of Federal Regulations Title 46, Part 56, for Piping
“Fiberglass” (Glass-Fiber-Reinforced Thermosetting-
8
3
Systems,andSubpart56.60-25forNonmetallicMaterials
Resin) Pipe and Tube
IMO Resolution A.653(16) Recommendation on Improved
D 2310 Classification for Machine-Made “Fiberglass”
3
Fire Test Procedures for Surface Flammability of Bulk-
(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
8
head, Ceiling, and Deck Finish Materials
D2584 Test Method for Ignition Loss of Cured Reinforced
4
Resins
1 5
This specification is under the jurisdiction ofASTM Committee F25 on Ships Annual Book of ASTM Standards, Vol 08.03.
6
and MarineTechnology and is the direct responsibility of Subcommittee F25.11 on Annual Book of ASTM Standards, Vol 04.07.
7
Machinery and Piping Systems. Available from American National Standards Institute, 25 W. 43rd St., 4th
Current edition approved Dec. 10, 2001. Published April 2002. Originally Floor, New York, NY 10036.
8
published as F1173–88. Last previous edition F1173–95. AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
2
Annual Book of ASTM Standards, Vol 08.01. Robbins Ave., Philadelphia, PA 19111-5098, Attn: NPODS.
3 9
Annual Book of ASTM Standards, Vol 08.04. Available from the National Sanitation Foundation, P.O. Box 130140, 789 N.
4
Annual Book of ASTM Standards, Vol 08.02. Dixboro Rd., Ann Arbor, MI 48113-0140.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1173–01
IMO Resolution MSC.61(67) International Code forAppli- 4.2.1 Rating Method 1—Short-term test.
8
cation of Fire Test Procedures 4.2.2 Rating Method 2—Medium-term (1000-h) test.
OTI 95 634 Jet-Fire Resistance Test of Passive Fire Protec- 4.2.3 Rating Method 3—Long-term (10000-h) test.
10
tion Materials 4.2.4 Rating Method 4—Long-term (10000-h) regression
2.3 ISO Documents:
test.
7
9001 4.3
...