iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM B829-04a(2009)

(Specification)

Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube

Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube

ABSTRACT
This general specification contains the mandatory requirements to the ASTM standards listed herein for seamless pipes and tubes made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
SCOPE
1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:
Title of SpecificationASTM
Designation  Nickel Seamless Pipe and TubeB 161 Seamless Nickel and Nickel Alloy, Condenser and Heat Ex-
changer Tubes B 163 Nickel-Copper Alloy (UNS N04400) Seamless Pipe and TubeB 165 Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and
N06690) Seamless Pipe and TubeB 167 Nickel-Iron-Chromium Alloy Seamless Pipe and TubeB 407 Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825
and N08221) Seamless Pipe and TubeB 423 Nickel-Chromium-Molybdenum-Columbium Alloys (UNS
N06625) Pipe and Tube B 444 Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy
(UNS N06102) Seamless Pipe and TubeB 445 Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS
N08332) Seamless PipeB 535 Copper-Beryllium Alloy Forgings and Extrusion B 570 Seamless Nickel and Nickel-Cobalt Alloy Pipe and TubeB 622 UNS N08028 Seamless TubesB 668 UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe
and TubeB 677 Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and
UNS N08367) Seamless Pipe and TubeB 690 Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and
TubeB 722 Seamless UNS N08020, UNS N08026, and UNS N08024
Nickel-Alloy Pipe and TubeB 729
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
14-Apr-2009
ICS
23.040.15 - Non-ferrous metal pipes
Technical Committee
B02 - Nonferrous Metals and Alloys
Drafting Committee
B02.07 - Refined Nickel and Cobalt and Their Alloys
Current Stage
Ref Project

Relations

Replaces
ASTM B829-04a - Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B167-18 - Standard Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674), and Nickel-Chromium-Molybdenum-Copper Alloy (UNS N06235) Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B983-21 - Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B163-22 - Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
Effective Date
15-Apr-2009
Referred By
ASTM B1020/B1020M-22 - Standard Specification for Seamless Nickel Alloy Mechanical Tubing and Hollow Bar
Effective Date
15-Apr-2009
Referred By
ASTM B677-23 - Standard Specification for Nickel-Iron-Chromium-Molybdenum, Iron-Nickel-Chromium-Molybdenum-Copper, and Nickel-Iron-Chromium-Molybdenum-Nitrogen Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B668-14(2019) - Standard Specification for UNS N08028 and N08029 Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B165-19 - Standard Specification for Nickel-Copper Alloy Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B161-05(2019) - Standard Specification for Nickel Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B407-22 - Standard Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B535-06(2022) - Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B924-02(2022) - Standard Specification for Seamless and Welded Nickel Alloy Condenser and Heat Exchanger Tubes With Integral Fins
Effective Date
15-Apr-2009
Referred By
ASTM B423-22 - Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy Seamless Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B444-23 - Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloys<brk/> and Nickel-Chromium-Molybdenum-Silicon Alloy Pipe and Tube
Effective Date
15-Apr-2009
Referred By
ASTM B622-17b - Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
Effective Date
15-Apr-2009

Buy Standard

ASTM B829-04a(2009) - Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and TubeASTM B829-04a(2009) - Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
PreviousNext
Technical specification
ASTM B829-04a(2009) - Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM B829-04a(2009) - Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and TubeREDLINE ASTM B829-04a(2009) - Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
PreviousNext
Technical specification
REDLINE ASTM B829-04a(2009) - Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B829 −04a(Reapproved2009)
Standard Specification for
General Requirements for Nickel and Nickel Alloys
1
Seamless Pipe and Tube
This standard is issued under the fixed designation B829; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.3 In case of conflict between a requirement of the product
specification and a requirement of this general specification,
1.1 This specification contains various requirements that,
only the requirement of the product specification needs to be
with the exception of Sections 5 and 10, are mandatory
satisfied.
requirements to the following ASTM nickel and nickel alloy,
seamless pipe and tube specifications: 1.4 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
ASTM
Title of Specification
2
Designation
conversions to SI units that are provided for information only
Nickel Seamless Pipe and Tube B161
and are not considered standard.
Seamless Nickel and Nickel Alloy, Condenser and Heat Ex- B163
changer Tubes
1.5 The following safety hazards caveat pertains only to the
Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube B165
test requirements portion, Section 5, of this specification: This
Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and B167
standard does not purport to address all of the safety concerns,
N06690) Seamless Pipe and Tube
Nickel-Iron-Chromium Alloy Seamless Pipe and Tube B407
if any, associated with its use. It is the responsibility of the user
Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 B423
of this standard to become familiar with all hazards including
and N08221) Seamless Pipe and Tube
those identified in the appropriate Material Safety Data Sheet
Nickel-Chromium-Molybdenum-Columbium Alloys (UNS B444
N06625) Pipe and Tube
(MSDS) for this product/material as provided by the
Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy B445
manufacturer, to establish appropriate safety and health
(UNS N06102) Seamless Pipe and Tube
Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS B535 practices, and determine the applicability of regulatory limi-
N08332) Seamless Pipe
tations prior to use.
Copper-Beryllium Alloy Forgings and Extrusion B570
Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube B622
2. Referenced Documents
UNS N08028 Seamless Tubes B668
2
UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe B677
2.1 ASTM Standards:
and Tube
B880 Specification for General Requirements for Chemical
Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and B690
UNS N08367) Seamless Pipe and Tube Check Analysis Limits for Nickel, Nickel Alloys and
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and B722
Cobalt Alloys
Tube
E8/E8M Test Methods for Tension Testing of Metallic Ma-
Seamless UNS N08020, UNS N08026, and UNS N08024 B729
Nickel-Alloy Pipe and Tube
terials
E18 Test Methods for Rockwell Hardness of Metallic Ma-
1.2 One or more of the test requirements of Section 5 apply
terials
only if specifically stated in the product specification or in the
E29 Practice for Using Significant Digits in Test Data to
purchase order.
Determine Conformance with Specifications
E39 Methods for Chemical Analysis of Nickel (Withdrawn
1
This specification is under the jurisdiction of ASTM Committee B02 on
3
1995)
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys.
E76 Test Methods for Chemical Analysis of Nickel-Copper
Current edition approved April 15, 2009. Published April 2009. Originally 3
Alloys (Withdrawn 2003)
approved in 1992. Last previous edition approved in 2004 as B829 – 04a. DOI:
E112 Test Methods for Determining Average Grain Size
10.1520/B0829-04AR09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B829−04a(2009)
E213 Practice for Ultrasonic Testing of Metal Pipe and (6.9 MPa) provided that the fiber stress, calculated from the
Tubing following equation, does not exceed the allowable fiber stress
E426 PracticeforElectromagnetic(Eddy-Current)Examina- for the material:
tion of Seam
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B 829–04a Designation: B829 – 04a (Reapproved 2009)
Standard Specification for
General Requirements for Nickel and Nickel Alloys
1
Seamless Pipe and Tube
This standard is issued under the fixed designation B829; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements
to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:
ASTM
Title of Specification
2
Designation
Nickel Seamless Pipe and Tube B161
Seamless Nickel and Nickel Alloy, Condenser and Heat Ex- B163
changer Tubes
Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube B165
Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and B167
N06690) Seamless Pipe and Tube
Nickel-Iron-Chromium Alloy Seamless Pipe and Tube B407
Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 B423
and N08221) Seamless Pipe and Tube
Nickel-Chromium-Molybdenum-Columbium Alloys (UNS B444
N06625) Pipe and Tube
Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy B445
(UNS N06102) Seamless Pipe and Tube
Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS B535
N08332) Seamless Pipe
Copper-Beryllium Alloy Forgings and Extrusion B570
Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube B622
UNS N08028 Seamless Tubes B668
UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe B677
and Tube
Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and B690
UNS N08367) Seamless Pipe and Tube
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and B722
Tube
Seamless UNS N08020, UNS N08026, and UNS N08024 B729
Nickel-Alloy Pipe and Tube
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the
purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only
the requirement of the product specification needs to be satisfied.
1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 1, 2004. Published October 2004. Originally approved in 1992. Last previous edition approved in 2004 as B 829–04.
Current edition approved April 15, 2009. Published April 2009. Originally approved in 1992. Last previous edition approved in 2004 as B829 – 04a. DOI:
10.1520/B0829-04AR09.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B829 – 04a (2009)
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B880 Specification for General Requirements for Chemical Che
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B619/B619M-19(2023)(Specification)
Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

ABSTRACT
This specification covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS 06002; UNS N06022; UNS N06035; UNS N06058; UNS N06059; UNS N06200; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; UNS N06210; and UNS R20033). Two classes of pipe are covered as Class I which is as welded and solution annealed or welded and sized and solution annealed; and Class II which is welded, cold worked, and solution annealed. All pipes shall be furnished in the solution annealed and descaled condition. The pipe shall be made from flat-rolled alloy by an automatic welding process with no addition of filler metal. Subsequent to welding and prior to final heat treatment, Class II pipes shall be cold worked either in both weld and base metal or in weld metal only. The material shall conform to the composition limits set by this specification. Tensile strength, yield strength and elongation of the material shall conform to the mechanical requirements. Tension test, flattening test, transverse guided bend test, and hydrostatic or nondestructive electric test shall be performed.
SCOPE
1.1 This specification2 covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06035; UNS N06044; UNS N06058; UNS N06059; UNS N06200; UNS N06235; UNS N10362; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N08034; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)3 as shown in Table 1.    
1.2 This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8 in. nominal pipe size and larger as set forth in ANSI B36.19 (see Table 2).  
1.3 Two classes of pipe are covered as follows:  
1.3.1 Class I—As welded and solution annealed or welded and sized and solution annealed.  
1.3.2 Class II—Welded, cold worked, and solution annealed.  
1.4 All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B677-23(Specification)
Standard Specification for Nickel-Iron-Chromium-Molybdenum, Iron-Nickel-Chromium-Molybdenum-Copper, and Nickel-Iron-Chromium-Molybdenum-Nitrogen Seamless Pipe and Tube

ABSTRACT
This specification covers UNS N08925, N08354, and N08926 alloy seamless, cold-worked or hot-finished pipes and tubes for use in general corrosive service. The materials should be supplied in solution-treated condition, heat treated and quenched in water or rapidly cooled by other means. The material chemical composition, mechanical properties, and required response to hydrostatic and nondestructive tests should conform to the values contained in this specification and related ASTM standards.
SCOPE
1.1 This specification covers UNS N08925, UNS N08354, UNS N089262, and UNS N08935 seamless, cold-worked or hot-finished pipe and tube intended for general corrosive service.  
1.2 ASTM International has adopted definitions whereby some grades, such as UNS N08904 previously in this specification, were recognized as stainless steels, because those grades have iron as the largest element by mass percent. Such grades are under the oversight of ASTM Committee A01 and its subcommittees. The products of N08904 previously covered in this specification are now covered by Specifications A269 and A312/A312M.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B675-22(Specification)
Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy Welded Pipe

ABSTRACT
This specification covers UNS N08367 welded pipes for general corrosion applications. The chemical composition, dimensions and mechanical properties for the welded pipes should be in accordance with those contained in this document and other ASTM documents specified herein.
SCOPE
1.1 This specification covers UNS N083672 welded pipe for general corrosion applications.  
1.2 Specification B775 lists the dimensions of welded stainless steel pipe as shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B163-22(Specification)
Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes

ABSTRACT
This specification covers seamless tubes of nickel and nickel alloy for use in condenser and heat-exchanger service. This covers outside diameter and average wall, or outside diameter and minimum wall tube. Tube shall be furnished in the alloys and conditions defined by this specification. The material shall conform to the composition limits of nickel, copper, molybdenum, iron, manganese, carbon, silicon, chromium, aluminium, titanium, phosphorus, cerium, zirconium, yttrium, born, cobalt, columblum, tungsten, and nitrogen specified. Tensile strength, yield strength, elongation, and Rockwell hardness of the material shall conform to the required mechanical properties set by this specification. Test methods such as chemical analysis, tension, rounding procedure, Rockwell hardness, grain size and hardness conversion shall be performed.
SCOPE
1.1 This specification2 covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service.    
1.2 This specification covers outside diameter and average wall, or outside diameter and minimum wall tube.  
1.2.1 The sizes covered by this specification are 3 in. (76.2 mm) and under in outside diameter with minimum wall thicknesses of 0.148 in. (3.76 mm) and under, and with average wall thicknesses of 0.165 in. (4.19 mm) and under.  
1.3 Tube shall be furnished in the alloys and conditions as shown in Table 2. For small diameter and light wall tube (converter sizes), see Appendix X2.    
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    14 pages
    English language
    sale 15% off
  • Technical specification
    14 pages
    English language
    sale 15% off
ASTM
ASTM B423-22(Specification)
Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy Seamless Pipe and Tube

ABSTRACT
This specification covers nickel-iron-chromium-molybdenum-copper alloys (UNS N08825 and UNS N08221) in the form of cold-worked and hot-finished seamless pipe and tube intended for general corrosive service. Material furnished under this specification shall conform to the applicable requirements specified. Chemical composition limits of the material such as nickel, chromium, iron, manganese, carbon, copper, silicon, sulfur, aluminum titanium, and molybdenum shall conform to the chemical requirements of this specification. Tensile strength, yield strength and elongation of the material under the specified condition and size shall also conform to the required mechanical properties. Hydrostatic and nondestructive electric tests shall be performed.
SCOPE
1.1 This specification2 covers nickel-iron-chromium-molybdenum-copper alloys3 in the form of cold-worked and hot-finished seamless pipe and tube intended for general corrosive service. The general requirements for pipe and tube are covered in Specification B829.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B407-22(Specification)
Standard Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube

ABSTRACT
This specification covers the standard requirements for nickel-iron-chromium alloy which include UNS N08120, UNS N08800, UNS N08801, UNS N08810, UNS N08811, UNS N08890, and UNS N06811 in the form of cold-worked and hot-finished annealed seamless pipe and tube. The materials shall be heat treated at certain annealing temperatures and shall conform to the chemical composition limits for nickel, chromium, iron, manganese, carbon, copper, silicon, sulfur, aluminum, titanium, columbium, molybdenum, niobium, tantalum, phosphorus, tungsten, cobalt, nitrogen, and boron. Planimetric method of measurement and tension test shall be conducted in full tubular size, longitudinal strip, or round specimens in the direction of fabrication to determine the grain size and mechanical properties, respectively. These materials shall conform to the specified grain size, yield strength, tensile strength, and elongation requirements. Each pipe or tube shall be subjected to hydrostatic or nondestructive eddy-current tests to determine the allowable fiber stress and to detect significant discontinuities such as drilled hole and transverse tangential notch. The cold-drawn material shall be commercially straight, uniform in quality and temper, smooth, and free of bends, kinks, and other injurious imperfections.
SCOPE
1.1 This specification2 covers UNS N08120, UNS N08800, UNS N08801, UNS N08810, UNS N08811, UNS N08890, and UNS N06811 in the form of cold-worked and hot-finished annealed seamless pipe and tube. Alloys UNS N08800 and UNS N06811 are normally employed in service temperatures up to and including 1100 °F (593 °C). Alloys UNS N08120, UNS N08810, UNS N08811, and UNS N08890 are normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture is required, and they are annealed to develop controlled grain size for optimum properties in this temperature range.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM B834-22(Specification)
Standard Specification for Pressure Consolidated Powder Nickel Alloy Pipe Flanges, Fittings, Valves, and Parts

ABSTRACT
This specification tackles standards for pressure consolidated powder metallurgy iron-nickel-chromium-molybdenum and nickel-chromium-molybdenum-columbium pipe flanges, fittings, valves, and parts intended for general corrosion or heat-resisting service. Compacts shall be manufactured by placing a single powder blend into a can, evacuating the can, and sealing it. The can material shall then be selected to ensure that it has no deleterious effect on the final product. The specimen shall be heated and placed under sufficient pressure for a sufficient period of time to ensure that the final consolidated part is fully dense. The powder shall be produced by vacuum melting followed by gas atomization. The heats shall be thoroughly mixed to ensure homogeneity when powder from more than one heat is used to make a blend. The material shall have the chemical compositions of carbon, manganese, silicon, phosphorus, sulfur, chromium, molybdenum, nickel, iron, cobalt, columbium, aluminum, titanium, nitrogen, and copper. Hydrostatic test shall be conducted and the specimen must show no leaks. The density test shall be performed using sample suspended from a scale and weighed in air and water using Archimede’s principle. Check Analysis shall be wholly the responsibility of the purchaser. The parts of the specimen shall be uniform in quality and condition, and shall be free from injurious imperfections.
SCOPE
1.1 This specification covers pressure consolidated powder metallurgy nickel alloy pipe flanges, fittings, valves, and parts intended for general corrosion or heat-resisting service.  
1.1.1 UNS N06625 products are furnished in two grades of different heat-treated conditions:
1.1.1.1 Grade 1 (annealed)—Material is normally employed in service temperatures up to 1100 °F (593 °C).
1.1.1.2 Grade 2 (solution annealed)—Material is normally employed in service temperatures above 1100 °F (593 °C) when resistance to creep and rupture is required.  
1.2 UNS N08367 products are furnished in the solution annealed condition.  
1.3 UNS N06600 products are furnished in the annealed condition.  
1.4 UNS N06690 products are furnished in the annealed condition.  
1.5 UNS N07718 products are furnished in the solution annealed + precipitation hardened condition.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following safety hazards caveat pertains only to test methods portions, Sections 7.3 and 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and to determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM B515-22(Specification)
Standard Specification for Welded Nickel-Iron-Chromium Alloy Tubes

ABSTRACT
This specification covers welded UNS N08120, UNS N08800, UNS N08810 and UNS N08811 alloy boiler, heat exchanger, and condenser tubes for general corrosion resisting and low or high-temperature service. Tube shall be made from flat-rolled alloy by an automatic welding process with no addition or filler metal, shall be cold-worked subsequent to welding and prior to final annealing, and shall be furnished with oxide removed. When bright annealing is used, descaling is not necessary. The material shall conform to the chemical composition limits prescribed for nickel, chromium, iron, manganese, carbon, copper, silicon, sulfur, aluminum, titanium, columbium, molybdenum, phosphorus, tungsten, cobalt, nitrogen, and boron, as determined by chemical analysis, and to the specified mechanical properties including tensile strength, yield strength, and elongation. Annealed alloys shall conform to the the prescribed grain size. The following tests shall be performed: (1) flattening test, (2) flange test, (3) Class 1 nondestructive test by one of the following: hydrostatic, pneumatic (air underwater), eddy current, or ultrasonic test, and (4) Class 2 nondestructive test by leak and electric (eddy current, or ultrasonic test) test.
SCOPE
1.1 This specification covers welded UNS N08120, UNS N08800, UNS N08810 and UNS N088112 alloy boiler, heat exchanger, and condenser tubes for general corrosion resisting and low or high-temperature service.  
1.2 This specification covers tubes 1/8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to 12.70 mm), inclusive, in wall thickness. Table 2 of Specification B751 lists the dimensional requirements of these sizes. Tubes having other dimensions may be furnished provided such tubing complies with all other requirements of this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B983-21(Specification)
Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube

ABSTRACT
This specification covers high strength, seamless pipe and tube of nickel alloys (UNS N07022, UNS N07725, and UNS N07740). Pipe and tube shall be supplied in the cold worked or cold worked and precipitations hardened or solution annealed plus precipitation hardened and descaled conditions. When atmosphere control is used, descaling is not necessary. Each pipe or tube shall be tested by the manufacturer by either hydrostatic or a non-destructive electric test in accordance with Specification B829. This specification also describes chemical requirements, heat treatments, and mechanical properties, as well as calculation of mass or weight, sampling of chemical analysis, sampling for mechanical testing, specimen preparation, inspection, and certification. There shall be one test per lot for chemical analysis and one test per lot for tension test. If the specimen used in the mechanical test of any lot fails to meet the specified requirements, tow additional specimens shall be taken from different sample pieces and tested. The results of the tests on both of these specimens shall meet the specified requirements.
SCOPE
1.1 This specification covers high strength, seamless pipe and tube of nickel alloys (UNS N07022, UNS N07725, UNS N07740, UNS N09945, UNS N09925, UNS N07718, UNS N10276, UNS N06985)2 as shown in Table 1.  
1.2 Pipe and tube shall be supplied in the cold worked or cold worked and precipitations hardened or solution annealed plus precipitation hardened and descaled conditions. When atmosphere control is used, descaling is not necessary.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM B1007-21(Specification)
Standard Specification for Welded Precipitation Hardenable or Cold Worked, Nickel Alloy Tube

ABSTRACT
This specification covers the manufacturing requirements and test methods for nominal and minimum wall-thickness welded tubes and welded and cold worked tubes 1/8 to 6 in. (3.2 to 152.4 mm) in outside diameter and 0.015 to 0.148 in. (0.41 to 3.7 mm) inclusive in wall thickness. The tubes are made from the following nickel alloys: aluminum, boron, carbon, chromium, cobalt, columbium, copper, iron, manganese, molybdenum, nickel, phosphorous, silicon, sulphur, titanium, tungsten, and vanadium. Anticipated uses cover applications where strength and strength at elevated temperatures are desired attributes. Some examples are hydraulic control lines, boilers, heat exchangers, and solar absorbers. The tubes shall be supplied in one of the following conditions: cold worked, cold worked and precipitation hardened, solution annealed plus precipitation hardened, or solution annealed and descaled conditions. When atmosphere control is used, descaling is not necessary.
This specification also covers ordering information, chemical and mechanical requirements, heat treatments, conditions representing different levels of mechanical properties, hydrostatic or nondestructive electric test, surface condition, weight, and workmanship, finish, and appearance.
SCOPE
1.1 This specification covers nominal and minimum wall-thickness welded tubes and welded and cold worked tubes made from the nickel alloys listed in Table 1. Anticipated uses cover applications where strength and strength at elevated temperatures are desired attributes. Some examples are hydraulic control lines, boilers, heat exchangers, and solar absorbers.  
1.2 Tube shall be supplied in one of the following conditions; cold worked, cold worked and precipitation hardened, solution annealed plus precipitation hardened, or solution annealed and descaled conditions. When atmosphere control is used, descaling is not necessary.  
1.3 This specification covers tube 1/8 to 6 in. (3.2 to 152.4 mm) in outside diameter and 0.015 to 0.148 in. (0.41 to 3.7 mm) inclusive in wall thickness.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off