ASTM B950-17
(Guide)Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys
Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys
SIGNIFICANCE AND USE
4.1 The Form and Style for ASTM Standards manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee B05 recognizes the need to provide a supplementary document pertaining to the types of products and materials covered by specifications under its jurisdiction.
4.2 This guide contains a list of sections to be considered for inclusion in a specification for copper and copper alloys, recommended wording, or both, for such sections. An electronic template including committee adopted language is included in the Appendix.7
4.3 Persons drafting new product specifications, or modifying existing ones, under the jurisdiction of Committee B05, should follow this guide and the requirements of the Form and Style Manual to ensure consistency.
SCOPE
1.1 This guide establishes the editorial procedures and form and style for product specifications under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys.
Note 1: For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style for ASTM Standards (Blue Book).2
1.2 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for use by the subcommittees within ASTM Committee B05 on Copper and Copper Alloys. This guide is to be applied in conjunction with the Form and Style Manual. The Appendix contains a copy of the B05 electronic template which includes adopted language for various sections and provides a template for drafting B05 product specifications.
Note 2: The contents of this guide were previously maintained as a white paper under the title, “ASTM Committee B05 Outline of Form of Specifications.”
1.3 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures outlined herein, and be guided by the latest specifications covering similar commodities.
1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of the current edition of the Form and Style Manual, this guide has precedence.
1.5 When patents are involved, the specifications writer should refer to the Form and Style Manual section on patents and trademarks. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B950 −17
Standard Guide for
Editorial Procedures and Form of Product Specifications for
1
Copper and Copper Alloys
This standard is issued under the fixed designation B950; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
1.1 This guide establishes the editorial procedures and form
mendations issued by the World Trade Organization Technical
and style for product specifications under the jurisdiction of
Barriers to Trade (TBT) Committee.
ASTM Committee B05 on Copper and Copper Alloys.
NOTE 1—For standards other than product specifications, such as test
2. Referenced Documents
methods, practices, and guides, see the appropriate sections of Form and
2
Style for ASTM Standards (Blue Book). 3
2.1 ASTM Standards:
1.2 This guide has been prepared as a supplement to the
B153 Test Method for Expansion (Pin Test) of Copper and
current edition of the Form and Style Manual, and is appro-
Copper-Alloy Pipe and Tubing
priate for use by the subcommittees within ASTM Committee
B154 Test Method for Mercurous Nitrate Test for Copper
B05 on Copper and CopperAlloys. This guide is to be applied
Alloys
in conjunction with the Form and Style Manual.TheAppendix
B170 Specification for Oxygen-Free Electrolytic Copper—
contains a copy of the B05 electronic template which includes
Refinery Shapes
adopted language for various sections and provides a template
B193 Test Method for Resistivity of Electrical Conductor
for drafting B05 product specifications.
Materials
NOTE 2—The contents of this guide were previously maintained as a
B194 SpecificationforCopper-BerylliumAlloyPlate,Sheet,
white paper under the title, “ASTM Committee B05 Outline of Form of
Strip, and Rolled Bar
Specifications.”
B216 Specification for Tough-Pitch Fire-Refined Copper—
1.3 Subcommittees preparing new product specifications or
Refinery Shapes
revising existing ones should follow the practices and proce-
B224 Classification of Coppers
duresoutlinedherein,andbeguidedbythelatestspecifications
B248 Specification for General Requirements for Wrought
covering similar commodities.
Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
1.4 If a conflict exists between this guide and the mandatory Bar
sections of the current edition of the Form and Style Manual, B248M SpecificationforGeneralRequirementsforWrought
the Form and Style Manual requirements have precedence. If a Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
conflict exists between this guide and the nonmandatory Bar (Metric)
sections of the current edition of the Form and Style Manual, B249/B249M Specification for General Requirements for
this guide has precedence. Wrought Copper and Copper-Alloy Rod, Bar, Shapes and
Forgings
1.5 When patents are involved, the specifications writer
B250/B250M Specification for General Requirements for
should refer to the Form and Style Manual section on patents
Wrought Copper Alloy Wire
and trademarks. Also, refer to part F of the Form and Style
B251/B251M Specification for General Requirements for
Manual for trademark information and the safety hazards
Wrought Seamless Copper and Copper-Alloy Tube
caveat.
B577 Test Methods for Detection of Cuprous Oxide (Hydro-
1.6 This international standard was developed in accor-
gen Embrittlement Susceptibility) in Copper
dance with internationally recognized principles on standard-
B601 ClassificationforTemperDesignationsforCopperand
Copper Alloys—Wrought and Cast
1
This guide is under the jurisdiction of ASTM Committee B05 on Copper and
CopperAlloys and is the direct responsibility of Subcommittee B05.91 on Editorial
and Publications.
3
Current edition approved Oct. 1, 2017. Published November 2017. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 2006. Last previous edition approved in 2016 as B950 – 16. DOI: contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
10.1520/B0950-17. Standards volume information, refer to the standard’s Document Summary page on
2
Available from ASTM website at: http://www.astm.org/COMMIT/Blue_Book. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B950−17
6
B824 Specification for General Requirements for Copper 2.3 JIS Document:
Alloy Castings JISH1068 MethodsforDeterminationofBismuthinCopper
and Copper A
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B950 − 16 B950 − 17
Standard Guide for
Editorial Procedures and Form of Product Specifications for
1
Copper and Copper Alloys
This standard is issued under the fixed designation B950; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This guide coversestablishes the editorial procedures and form and style for product specifications under the jurisdiction of
ASTM Committee B05 on Copper and Copper Alloys.
NOTE 1—For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style
2
for ASTM Standards (Blue Book).
1.2 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for
use by the subcommittees within ASTM Committee B05 on Copper and Copper Alloys. This guide is to be applied in conjunction
with the Form and Style Manual. The Appendix contains a copy of the B05 electronic template which includes adopted language
for various sections and provides a template for drafting B05 product specifications.
NOTE 2—The contents of this guide were previously maintained as a white paper under the title, “ASTM Committee B05 Outline of Form of
Specifications.”
1.3 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures
outlined herein, and be guided by the latest specifications covering similar commodities.
1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the
Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of
the current edition of the Form and Style Manual, this guide has precedence.
1.5 When patents are involved, the specifications writer should refer to the Form and Style Manual section on patents and
trademarks. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
B153 Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B170 Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B216 Specification for Tough-Pitch Fire-Refined Copper—Refinery Shapes
B224 Classification of Coppers
B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
(Metric)
B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
1
This guide is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.91 on Editorial and
Publications.
Current edition approved April 1, 2016Oct. 1, 2017. Published May 2016November 2017. Originally approved in 2006. Last previous edition approved in 20152016 as
B950 – 15.B950 – 16. DOI: 10.1520/B0950-16.10.1520/B0950-17.
2
Available from ASTM website at: http://www.astm.org/COMMIT/Blue_Book.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B950 − 17
B250/B250M Specification for General Requirements for Wrought Copper Alloy Wire
B251B251/B251M Specification for General Requirements for Wrought Seamles
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.