ASTM A455/A455M-12
(Specification)Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese
Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese
ABSTRACT
This specification covers high-tensile strength carbon-manganese steel plates intended for welded pressure vessels. Plates are normally supplied in the as-rolled condition. The plates may be ordered normalized or stress relieved, or both. The steel shall conform to the chemical composition requirements. The plates, as represented by the tension test specimens, shall conform to the mechanical property requirements.
SCOPE
1.1 This specification covers high-tensile strength carbon-manganese steel plates intended for welded pressure vessels.
1.2 This steel is usually made to a semi-killed or capped deoxidation practice; however, at the purchaser's or the steel producer's option, the steel may be made silicon-killed or aluminum-killed.
1.3 The maximum thickness of plates furnished under this specification shall be ¾ in. [20 mm].
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A455/A455M −12
Standard Specification for
Pressure Vessel Plates, Carbon Steel, High-Strength
1
Manganese
This standard is issued under the fixed designationA455/A455M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* line the testing and retesting methods and procedures, permit-
2 ted variations in dimensions, and mass, quality and repair of
1.1 This specification covers high-tensile strength carbon-
defects, marking, loading, and ordering information.
manganese steel plates intended for welded pressure vessels.
3.2 In addition to the basic requirements of this
1.2 This steel is usually made to a semi-killed or capped
specification, certain supplementary requirements are available
deoxidation practice; however, at the purchaser’s or the steel
when additional control, testing, or examination is required to
producer’s option, the steel may be made silicon-killed or
meet end use requirements. The purchaser is referred to the
aluminum-killed.
listed supplementary requirements in this specification and to
1.3 The maximum thickness of plates furnished under this
the detailed requirements in Specification A20/A20M.
3
specification shall be ⁄4 in. [20 mm].
3.3 Coils are excluded from qualification to this specifica-
1.4 For plates produced from coil and furnished without
tion until they are processed into finished plates. Plates
heat treatment or with stress relieving only, the additional
produced from coil means plates that have been cut to
requirements, including additional testing requirements and the
individuallengthsfromcoil.Theprocessordirectlycontrols,or
reporting of additional test results, of Specification A20/A20M
is responsible for, the operations involved in the processing of
apply.
coils into finished plates. Such operations include decoiling,
leveling, cutting to length, testing, inspection, conditioning,
1.5 The values stated in either inch-pound units or SI units
heat treatment (if applicable), packaging, marking, loading for
are to be regarded separately as standard. Within the text, the
shipment, and certification.
SI units are shown in brackets. The values stated in each
system are not exact equivalents; therefore, each system must
NOTE 1—For plates produced from coil and furnished without heat
be used independently of the other. Combining values from the treatment or with stress relieving only, three test results are reported for
each qualifying coil. Additional requirements regarding plates from coil
two systems may result in nonconformance with the specifi-
are described in Specification A20/A20M.
cation.
3.4 If the requirements of this specification are in conflict
2. Referenced Documents
with the requirements of Specification A20/A20M, the require-
3
ments of this specification shall prevail.
2.1 ASTM Standards:
A20/A20M SpecificationforGeneralRequirementsforSteel
4. Heat Treatment
Plates for Pressure Vessels
4.1 Plates are normally supplied in the as-rolled condition.
The plates may be ordered normalized or stress relieved, or
3. General Requirements and Ordering Information
both.
3.1 Material supplied to this material specification shall
conform to Specification A20/A20M. These requirements out-
5. Chemical Composition
5.1 The steel shall conform to the chemical requirements
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, given in Table 1.
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
6. Mechanical Properties
A01.11 on Steel Plates for Boilers and Pressure Vessels.
Current edition approved May 1, 2012. Published June 2012. Originally
6.1 Tension Test—The plates, as represented by the tension
approved in 1961. Last previous edition approved in 2007 as A455/
test specimens, shall conform to the requirements given in
A455M – 03 (2007). DOI: 10.1520/A0455_A0455M-12.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
Table 2.
cation SA-455/SA-455M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 7. Keywords
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7.1 carbon steel; high-strength steel plate for pressure pur-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. poses; welded pressure vessels
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A455/A455M − 12
TABLE 1 Chemical Re
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A455/A455M–03(Reapproved2007) Designation: A455/A455M – 12
Standard Specification for
Pressure Vessel Plates, Carbon Steel, High-Strength
1
Manganese
This standard is issued under the fixed designationA455/A455M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
2
1.1 This specification covers high-tensile strength carbon-manganese steel plates intended for welded pressure vessels.
1.2 Thissteelisusuallymadetoasemi-killedorcappeddeoxidationpractice;however,atthepurchaser’sorthesteelproducer’s
option, the steel may be made silicon-killed or aluminum-killed.
3
1.3 The maximum thickness of plates furnished under this specification shall be ⁄4 in. [20 mm].
1.4For1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional
requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M
apply.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard.Within the text, the SI units
are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification.
2. Referenced Documents
3
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
3. General Requirements and Ordering Information
3.1Plates3.1 Material supplied to this productmaterial specification shall conform to Specification A20/A20M, which outlines
the testing and retesting methods and procedures, permissible variations in dimensions and mass, quality and repair of defects,
marking, loading, etc.
3.2Specification . These requirements outline the testing and retesting methods and procedures, permitted variations in
dimensions, and mass, quality and repair of defects, marking, loading, and ordering information.
3.2 In addition to the basic requirements of this specification, certain supplementary requirements are available when additional
control, testing, or examination is required to meet end use requirements. The purchaser is referred to the listed supplementary
requirementsinthisspecificationandtothedetailedrequirementsinSpecificationA20/A20Malsoestablishestherulesforordering
information that should be complied with when purchasing plates to this specification.
3.3In addition to the basic requirements of this specification, certain supplementary requirements are available where additional
control, testing, or examination is required to meet end use requirements.
3.4The purchaser is referred to the listed supplementary requirements in this specification and to the detailed requirements in
Specification A20/A20M.
3.5Coils3.3 Coils are excluded from qualification to this specification until they are processed into finished plates. Plates
produced from coil means plates that have been cut to individual lengths from coil. The processor directly controls, or is
responsible for, the operations involved in the processing of coils into finished plates. Such operations include decoiling, leveling,
cutting to length, testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and
certification.
NOTE 1—For plates produced from coil and furnished without heat treatment or with stress relieving only, three test results are reported for each
qualifying coil. Additional requirements regarding plates from coil are described in Specification A20/A20M.
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Nov.May 1, 2007.2012. Published March 2008.June 2012. Originally approved in 1961. Last previous edition approved in 20032007 as
A455/A455M – 03 (2007). DOI: 10.1520/A0455_A0455M-03R07.10.1520/A0455_A0455M-12.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-455/SA-455M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volum
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.