ASTM A533/A533M-09e1
(Specification)Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel
Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel
ABSTRACT
This specification covers manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates for use in welded pressure vessels. The steel materials shall be killed and shall conform to the required values of fine austenitic grain and shall also be heat treated. The steel specimens shall undergo heat analysis and product analysis and shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, silicon, molybdenum, and nickel. Tension tests shall be performed wherein the steel specimens shall conform to the required values of tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification covers one type of manganese-molybdenum and four types of manganese-molybdenum-nickel alloy steel plates for use in the quenched and tempered condition for the construction of welded pressure vessels.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: A533/A533M −09 Usedin USDOE-NE Standards
Standard Specification for
Pressure Vessel Plates, Alloy Steel, Quenched and
Tempered, Manganese-Molybdenum and Manganese-
1
Molybdenum-Nickel
This standard is issued under the fixed designationA533/A533M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Editorial corrections made to Table 1 in May 2011.
1. Scope* 1.7 Plates covered by this specification are often used in the
2 beltline region of nuclear reactor vessels where the material
1.1 This specification covers one type of manganese-
properties may be affected by high levels of radiation. Appen-
molybdenum and four types of manganese-molybdenum-
dix X1 provides some information pertinent to this usage.
nickel alloy steel plates for use in the quenched and tempered
condition for the construction of welded pressure vessels. 1.8 The values stated in either inch-pound units or SI units
are to be regarded separately as standard. Within the text, the
1.2 Material under this specification is available in five
SI units are shown in brackets. The values stated in each
types, designated “A”, “B”, “C”, “D”, and “E”. The material is
system are not exact equivalents; therefore, each system must
also available in three classes having the following strength
be used independently of the other. Combining values from the
levels.
two systems may result in nonconformance with the specifi-
Tensile Strength,
Class
cation.
ksi [MPa]
1 80–100 [550 to 690]
2. Referenced Documents
2 90–115 [620 to 795]
3 100–125 [690 to 860]
3
2.1 ASTM Standards:
1.3 The maximum thickness of Class 1 and Class 2 plates is
A20/A20M SpecificationforGeneralRequirementsforSteel
limited only by the capacity of the composition to meet the
Plates for Pressure Vessels
specified mechanical property requirements; however, current
A435/A435M Specification for Straight-Beam Ultrasonic
practice normally limits the maximum thickness to 12 in. [300
Examination of Steel Plates
mm] for Types A through D. Current practice limits the
A577/A577M Specification for Ultrasonic Angle-Beam Ex-
maximum thickness for Type E to 6 in. [150 mm] for Class 1
amination of Steel Plates
1
and 3 ⁄4 in. [80 mm] for Class 2.
A578/A578M Specification for Straight-Beam Ultrasonic
1
1.4 The maximum thickness of Class 3 plates is 2 ⁄2 in. [65
Examination of Rolled Steel Plates for Special Applica-
mm] for Types A through D and 2 in. [50 mm] for Type E. tions
1.5 The minimum nominal thickness of plates of all classes
3. General Requirements and Ordering Information
is 0.25 in. [6.5 mm].
3.1 Material supplied to this material specification shall
1.6 These alloy steel plates in the as-rolled condition are
conform to Specification A20/A20M. These requirements out-
sensitivetocrackingduringtransitandhandling,particularlyin
line the testing and retesting methods and procedures, permit-
thicknesses over about 1 or 2 in. [25 or 50 mm]. They should
ted variations in dimensions, and mass, quality and repair of
be shipped in the as-rolled conditions only by mutual agree-
defects, marking, loading, and ordering information.
ment of manufacturer and the purchaser.
3.2 In addition to the basic requirements of this
specification, certain supplementary requirements are available
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
when additional control, testing, or examination is required to
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.11 on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Oct. 1, 2009. Published December 2009. Originally
3
approved in 1965. Last previous edition approved in 2004 as A533/ For referenced ASTM standards, visit the ASTM website, www.astm.org, or
´1
A533M – 93 (2004) . DOI: 10.1520/A0533_A0533M-09E01. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA-533/SA-533M in Section II of that Code. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
A533/A533M − 09
meet
1
---------------------- Page: 2 ----------------------
´1
A533/A533M − 09
TABLE 1 Chemical Requirements
4. Manufacture
NOTE 1—Where
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE Standards
´1
Designation:A533/A533M–09 Designation: A533/A533M – 09
Standard Specification for
Pressure Vessel Plates, Alloy Steel, Quenched and
Tempered, Manganese-Molybdenum and Manganese-
1
Molybdenum-Nickel
This standard is issued under the fixed designationA533/A533M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Editorial corrections made to Table 1 in May 2011.
1. Scope*
2
1.1 Thisspecification coversonetypeofmanganese-molybdenumandfourtypesofmanganese-molybdenum-nickelalloysteel
plates for use in the quenched and tempered condition for the construction of welded pressure vessels.
1.2 Material under this specification is available in five types, designated “A”, “B”, “C”, “D”, and “E”. The material is also
available in three classes having the following strength levels.
Tensile Strength,
Class
ksi [MPa]
1 80–100 [550 to 690]
2 90–115 [620 to 795]
3 100–125 [690 to 860]
1.3 ThemaximumthicknessofClass1andClass2platesislimitedonlybythecapacityofthecompositiontomeetthespecified
mechanical property requirements; however, current practice normally limits the maximum thickness to 12 in. [300 mm] forTypes
1
A through D. Current practice limits the maximum thickness for Type E to 6 in. [150 mm] for Class 1 and 3 ⁄4 in. [80 mm] for
Class 2.
1
1.4 The maximum thickness of Class 3 plates is 2 ⁄2 in. [65 mm] for Types A through D and 2 in. [50 mm] for Type E.
1.5 The minimum nominal thickness of plates of all classes is 0.25 in. [6.5 mm].
1.6 These alloy steel plates in the as-rolled condition are sensitive to cracking during transit and handling, particularly in
thicknesses over about 1 or 2 in. [25 or 50 mm]. They should be shipped in the as-rolled conditions only by mutual agreement of
manufacturer and the purchaser.
1.7 Plates covered by this specification are often used in the beltline region of nuclear reactor vessels where the material
properties may be affected by high levels of radiation. Appendix X1 provides some information pertinent to this usage.
1.8 Thevaluesstatedineitherinch-poundunitsorSIunitsaretoberegardedseparatelyasstandard.Withinthetext,theSIunits
are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification.
2. Referenced Documents
3
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
A578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
3. General Requirements and Ordering Information
3.1 Material supplied to this material specification shall conform to Specification A20/A20M. These requirements outline the
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.11
on Steel Plates for Boilers and Pressure Vessels.
´1
Current edition approved Oct. 1, 2009. Published December 2009. Originally approved in 1965. Last previous edition approved in 2004 as A533/A533M – 93 (2004) .
DOI: 10.1520/A0533_A0533M-09. . DOI: 10.1520/A0533_A0533M-09E01.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-533/SA-533M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
´1
A533/A533M – 09
testing and retesting methods and procedures, permitted variations in dimensions, and mass, quality and repair of defects, marking,
loading, and ordering information.
3.2 In addition to the basic requirements of this
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.