iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3381-92(1999)

(Specification)

Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction

Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction

SCOPE
1.1 This specification covers asphalt cements graded by viscosity at 140°F (60°C) for use in pavement construction. Three sets of limits are offered in this specification. The purchaser shall specify the applicable table of limits. In the event the purchaser does not specify limits, Table 1 shall apply. For asphalt cements graded by penetration at 77°F (25°C) (see Specification D946). If needed, volume corrections for asphalt cements should be made according to Practice D4311.

General Information

Status
Historical
Publication Date
09-Feb-1999
ICS
93.080.10 - Road construction
Technical Committee
D04 - Road and Paving Materials
Drafting Committee
D04.40 - Asphalt Specifications
Current Stage
Ref Project

Relations

Replaced By
ASTM D3381-05 - Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction
Effective Date
01-Dec-2005
Referred By
ASTM D7564/D7564M-16 - Standard Practice for Construction of Asphalt-Rubber Cape Seal
Effective Date
10-Feb-1999
Referred By
ASTM D5360-15 - Standard Practice for Design and Construction of Bituminous Surface Treatments
Effective Date
10-Feb-1999

Buy Standard

ASTM D3381-92(1999) - Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement ConstructionASTM D3381-92(1999) - Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction
PreviousNext
Technical specification
ASTM D3381-92(1999) - Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
Designation: D 3381 – 92 (Reapproved 1999)
Standard Specification for
Viscosity-Graded Asphalt Cement for Use in Pavement
Construction
This standard is issued under the fixed designation D 3381; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D 2171 Test Method for Viscosity of Asphalts by Vacuum
Capillary Viscometer
1.1 This specification covers asphalt cements graded by
D 2872 Test Method for Effect of Heat andAir on a Moving
viscosity at 140°F (60°C) for use in pavement construction.
Film of Asphalt (Rolling Thin-Film Oven Test)
Three sets of limits are offered in this specification. The
D 4311 Practice for Determining Asphalt Volume Correc-
purchaser shall specify the applicable table of limits. In the
tion to a Base Temperature
event the purchaser does not specify limits,Table 1 shall apply.
For asphalt cements graded by penetration at 77°F (25°C) (see
3. Manufacture
Specification D 946). If needed, volume corrections for asphalt
3.1 The asphalt cement shall be prepared from crude petro-
cements should be made according to Practice D 4311.
leum by suitable methods.
2. Referenced Documents
4. Physical Requirements
2.1 ASTM Standards:
4.1 The asphalt cement shall be homogeneous, free from
D5 Test Method for Penetration of Bituminous Materials
water, and shall not foam when heated to 347°F (175°C).
D92 Test Method for Flash and Fire Points by Cleveland
4.2 The asphalt cements shall conform to the requirements
Open Cup
given in Table 1, Table 2,or Table 3, as specified by the
D95 Test Method for Water in Petroleum Products and
purchaser.
Bituminous Materials by Distillation
D113 Test Method for Ductility of Bituminous Materials
5. Methods of Sampling and Testing
D 140 Practice for Sampling Bituminous Materials
5.1 Sample and test asphalt cements in accordance with the
D 946 Specification for Penetration-Graded Asphalt Ce-
2 following methods:
ment for Use in Pavement Construction
5.1.1 Sampling—Practice D 140.
D 1754 Test Method for Effect of Heat andAir onAsphaltic
2 5.1.2 Water—Test MethodD95.
Materials (Thin-Film Oven Test)
5.1.3 Viscosity at 140°F (60°C)—Test Method D 2171.
D 2042 Test Method for Solubility of Asphalt Materials in
2 5.1.4 Viscosity at 275°F (135°C)—Test Method D 2170.
Trichloroethylene
5.1.5 Penetration— Test MethodD5.
D 2170 Test Method for Kinematic Viscosity of Asphalts
2 5.1.6 FlashPoint,ClevelandOpenCup—Test MethodD92
(Bitumens)
(see Table 1 and Table 2).
5.1.7 Solubility in Trichloroethylene—Test Method D 2042.
5.1.8 Thin-Film Oven Test—Test Method D 1754 (seeTable
This specification is under the jurisdiction of ASTM Committee D-4 on Road
1 and Table 2).
and Paving Materials and is the direct responsibility of Subcommittee D04.40 on
Asphalt Specifications.
5.1.9 Rolling Thin-Film Oven Test—Test Method D 2872
Current edition approved Feb. 15, 1992. Published May 1992. Originally
(see Table 3).
e1
published as D3381 – 75. Last previous edition D3381 – 83 .
2 5.1.10 Ductility—Test MethodD113.
Annual Book of ASTM Standards, Vol 04.03.
Annual Book of ASTM Standards, Vol 05.01.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
D 3381 – 92 (1999)
TABLE 1 Requirements for Asphalt Cement, Visco
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1752-18(2023)(Specification)
Standard Specification for Preformed Sponge Rubber, Cork, and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction

ABSTRACT
This specification covers preformed expansion joint fillers for use in concrete, brick, stone, and other paving and structural construction. The fillers are available in the following types: Type I, sponge rubber, which shall consist of preformed strips of a durable elastic sponge rubber compound using synthetic rubber or natural rubber as a base and containing no reclaim rubber or factice; Type II, cork, and Type III, self-expanding cork, which shall both consist of preformed strips that have been formed from clean granulated cork particles securely bound together by a synthetic resin of an incoluble nature; and Type IV, recycled PVC, which shall consist of preformed strips that have been extruded using scrap PVC material and using either no binder or a synthetic resin of an insoluble nature to securely bind it together. Materials shall be sampled suitably according to specified size and number, and shall meet property requirements as to recovery, compression, extrusion, expansion, boiling in hydrochloric acid, and density.
SCOPE
1.1 This specification covers preformed expansion joint fillers of the following four types for use in concrete, brick, or stone construction.  
1.1.1 Type I—Sponge rubber.  
1.1.2 Type II—Cork.  
1.1.3 Type III—Self-expanding cork.  
1.1.4 Type IV—Recycled PVC.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1: Attention is called to Specifications D994/D994M and D1751.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2950/D2950M-22(Test Method)
Standard Test Method for Density of Asphalt Mixtures in Place by Nuclear Methods

SIGNIFICANCE AND USE
4.1 The test method described is useful as a rapid, nondestructive technique for determining the in-place density of compacted asphalt mixtures.  
4.2 With proper calibration and confirmation testing, the test method is suitable for quality control and acceptance testing of compacted asphalt mixtures.  
4.3 The test method can be used to establish the proper rolling effort and pattern to achieve the required density.  
4.4 The nondestructive nature of the test allows repetitive measurements to be made at a single test location between roller passes and to monitor changes in density.  
4.5 The density results obtained by this test method are relative. Correlation with other test methods such as D1188/D1188M, D2726/D2726M, or D6752/D6752M is required to convert the results obtained using this method to actual density. It is recommended that at least seven core densities and seven nuclear densities be used to establish a conversion factor. A new factor must be established at any time a change is made in the paving mixture or in the construction process.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method describes a test procedure for determining the density of asphalt mixtures by the attenuation of gamma radiation, where the source and detector(s) remain on the surface (backscatter method) or the source or detector is placed at a known depth up to 300 mm [12 in.] while the detector or source remains on the surface (direct transmission method).  
1.2 The density, in mass per unit volume of the material under test, is determined by comparing the detected rate of gamma emissions with previously established calibration data.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 All observed and calculated values shall conform to the guide for significant digits and rounding established in Practice D6026.  
1.5 For limitations, see Section 5 on Interferences.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. It is the recommendation of Committee D04 that the following note be added to the end of the Significance and Use section of all applicable standards. Applicable standards are those in which measurement or calibration are made, sample are procured, or products are selected. The subcommittee shall determine the appropriateness of adding the note throughout the consensus process.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Develo...

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D979/D979M-22(Practice)
Standard Practice for Sampling Asphalt Mixtures

SIGNIFICANCE AND USE
4.1 General:  
4.1.1 Sampling is equally as important as the testing, and the sampler shall take every precaution to obtain samples that will yield an acceptable estimate of the nature and conditions of the materials which they represent.  
4.1.2 Samples for the development of preliminary data are obtained by the party responsible for the development of the data. Samples for control of the product at the source of manufacture or storage, or at the site of use, are obtained by the manufacturer, contractor, or other parties responsible for accomplishing the work. Samples for tests to be used in acceptance or rejection decisions by the purchaser are obtained by the purchaser or his authorized representative.  
4.1.3 This standard shall not be used for the sampling of compacted asphalt mixtures. Practice D5361/D5361M shall be used.
SCOPE
1.1 This practice covers sampling of asphalt mixtures at points of manufacture, storage, delivery, or in place.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D448-12(2022)(Classification)
Standard Classification for Sizes of Aggregate for Road and Bridge Construction

SIGNIFICANCE AND USE
4.1 Some contract documents specify certain aggregate sizes for specific uses or may suggest one or more of these sizes as appropriate for the preparation of various end-product mixtures. In some cases, closer limits on variability of the aggregate grading are required.
SCOPE
1.1 This classification defines aggregate size number designations and standard size ranges for mechanical sieve analyses of coarse aggregate and screenings for use in the construction and maintenance of various types of highways and bridges.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.  
1.3 The text of this classification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the classification.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1073-16(2022)(Specification)
Standard Specification for Fine Aggregate for Asphalt Paving Mixtures

ABSTRACT
This specification covers fine aggregate for use in bituminous paving mixtures. The aggregate shall be sampled to meet the requirements prescribed. Grading, fineness modulus and plasticity index shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers fine aggregate for use in asphalt paving mixtures.  
1.2 This specification is intended to describe material from a single source. When material from two or more sources is to be blended to produce a grading to meet requirements in other specifications for asphalt paving mixtures, the grading requirements of Table 1 of this specification are not applicable.  
Note 1: When obtaining materials from two or more sources that are to be blended to produce the final mix, it is recommended that the specifying or the ordering agency specify the alternative gradings and blend ratios to be supplied.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Sieve numbers shown in the text and Table 1 are labels only and are included for ease of reference of the user of this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1139/D1139M-22(Specification)
Standard Specification for Aggregate for Single or Multiple Asphalt Surface Treatments

ABSTRACT
This specification covers the quality and sizes of crushed stone, crushed slag, crushed expanded shale, crushed expanded clay, crushed expanded slate, and crushed or uncrushed gravel suitable for use as aggregate in single or multiple bituminous surface treatments. Tests shall be performed to determine the properties of the material in accordance with the following test methods: sampling; random sampling; degradation resistance; bulk density of aggregates; sulfate soundness; sieve analysis; clay lumps and friable particles; lightweight pieces; and flat and elongated pieces.
SCOPE
1.1 This specification covers the quality and sizes of crushed stone, crushed slag, crushed expanded shale, crushed expanded clay, crushed expanded slate, and crushed or uncrushed gravel suitable for use as aggregate in single or multiple asphalt surface treatments.  
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3.1 Regarding sieves, per Specification E11: “The values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth. The values stated in inch-pound units shall be considered standard with regard to the sieve frames.” When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8-22a(Terminology)
Standard Terminology Relating to Materials for Roads and Pavements

SCOPE
1.1 This standard incorporates generic terms and generic definitions of terms specifically associated with road and paving materials. These generic terms and definitions are used within the standards developed by Committee D04 on Road and Paving Materials.  
1.2 Only terms that appear in more than one standard under the jurisdiction of Committee D04 will be included in Section 3 of Terminology D8. Terms that were historically part of this terminology but never appeared, or no longer appear, in more than one standard under the jurisdiction of Committee D04 are listed in Appendix X1. The terms in Appendix X1 are not maintained and updated by Subcommittee D04.91. The terms in Appendix X1 are available for reference purposes only. The terminology in Appendix X1 may not reflect current practices, standards, and technology used in materials for roads and pavements.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3910-21(Practice)
Standard Practices for Design, Testing, and Construction of Slurry Seal

SIGNIFICANCE AND USE
4.1 These slurry seal practices are written as a guide and should not be construed as specifications.  
4.2 End-use specifications should be adopted to conform to job and user requirements.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 These practices cover the design, testing, and construction of mixtures for surface treatment of pavements. It is written as a guide and should be used as such. End-use specifications should be adapted to conform to job and user requirements.  
1.2 The values stated in SI units are to be regarded as the standard. The non-SI units used in this standard are allowed by the subcommittee for clarification in the use of the standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D4552/D4552M-20(Classification)
Standard Classification for Hot-Mix Recycling Agents

SIGNIFICANCE AND USE
3.1 Recycling of deteriorated asphalt pavements is being used with increasing frequency for its economy and benefit of conserving raw materials. The objective of recycling is to reuse the two ingredients of asphalt concrete-aggregate and asphalt binder and to restore the desired properties to the mixture. Recycling is carried out hot or cold, depending on the condition of the deteriorated pavement, construction procedure, availability of equipment, and cost. This classification is for classifying recycling agents to be used in recycled asphalt mixtures.  
Note 3: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This standard covers a standardized method whereby recycling agents to be used in hot recycling of asphalt concrete can be classified. The recycling agents are classified by viscosity in mm2/s measured at 60 °C [140 °F]. This classification does not apply to emulsified recycling agents.  
1.2 This standard does not address the performance of asphalt binder blends with recycling agents, or that of hot-mix asphalt mixture containing recycling agents. Adherence of a recycling agent to this specification does not necessarily relate to the performance of asphalt binders and mixtures containing the recycling agents.
Note 1: The impact of recycling agents has been evaluated by extracting the asphalt binder from the pavement to be recycled, and combining with the recycling agent to meet the appropriate grade within Specification D946/D946M or Table 1, 2, or 3 of Specification D3381/D3381M. More recently, some specifications have referred to performance grading as described in Specification D6373 or D8239.
Note 2: Efforts are underway to utilize performance-based testing of the asphalt mixture containing recycling agents as a measure of compliance.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off