ASTM C926-19
(Specification)Standard Specification for Application of Portland Cement-Based Plaster
Standard Specification for Application of Portland Cement-Based Plaster
ABSTRACT
This specification covers the standard requirements for the application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. It also sets forth tables for proportioning of various plaster mixes and plaster thickness. The materials used shall consist of the following: cement which shall be a Portland cement, air-entraining Portland cement, masonry cement, blended hydraulic cement, air-entraining blended hydraulic cement, or plastic cement; Type S hydrated lime; aggregates such as perlite and sand for base and job-mixed finish coats; water to be used in mixing; admixtures; and fibers. Surfaces of solid bases such as masonry, stone, cast-in-place or precast concrete shall be prepared either by sandblasting, wire brushing, acid etching, chipping, or a combination thereof. Details on curing to resist cracking; materials protection and storage; environmental conditions; and application of plaster, finish-coat, and fog-coat, which shall be done by hand or machine up to the specified nominal thickness on metal and solid plaster bases are discussed.
SCOPE
1.1 This specification covers the requirements for the application of full thickness portland cement-based plaster for exterior (stucco) and interior work. These requirements do not by default define a unit of work or assign responsibility for contractual purposes, which is the purview of a contract or contracts made between contracting entities.
1.2 This specification sets forth tables for proportioning of various plaster mixes and plaster thickness.
Note 1: General information will be found in Annex A1. Design considerations will be found in Annex A2.
1.3 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.
1.5 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C926 −19
Standard Specification for
1
Application of Portland Cement-Based Plaster
This standard is issued under the fixed designation C926; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* C11Terminology Relating to Gypsum and Related Building
Materials and Systems
1.1 This specification covers the requirements for the appli-
C25Test Methods for Chemical Analysis of Limestone,
cation of full thickness portland cement-based plaster for
Quicklime, and Hydrated Lime
exterior (stucco) and interior work. These requirements do not
C35Specification for InorganicAggregates for Use in Gyp-
by default define a unit of work or assign responsibility for
sum Plaster
contractual purposes, which is the purview of a contract or
C91/C91MSpecification for Masonry Cement
contracts made between contracting entities.
C150/C150MSpecification for Portland Cement
1.2 This specification sets forth tables for proportioning of
C206Specification for Finishing Hydrated Lime
various plaster mixes and plaster thickness.
C207Specification for Hydrated Lime for Masonry Pur-
poses
NOTE 1—General information will be found in Annex A1. Design
considerations will be found in Annex A2. C219Terminology Relating to Hydraulic Cement
C260/C260MSpecification for Air-Entraining Admixtures
1.3 The text of this specification references notes and
for Concrete
footnotes that provide explanatory material. These notes and
C578Specification for Rigid, Cellular Polystyrene Thermal
footnotes (excluding those in tables and figures) shall not be
Insulation
considered as requirements of the specification.
C595/C595MSpecification for Blended Hydraulic Cements
1.4 Details of construction for a specific assembly to
C631Specification for Bonding Compounds for Interior
achieve the required fire resistance shall be obtained from
Gypsum Plastering
reports of fire-resistance tests, engineering evaluations, or
C897Specification for Aggregate for Job-Mixed Portland
listings from recognized fire testing laboratories.
Cement-Based Plasters
1.5 Thevaluesstatedininch-poundunitsaretoberegarded
C932 Specification for Surface-Applied Bonding Com-
asthestandard.TheSI(metric)valuesgiveninparenthesesare
pounds for Exterior Plastering
approximate and are provided for information purposes only.
C1063Specification for Installation of Lathing and Furring
to Receive Interior and Exterior Portland Cement-Based
1.6 This international standard was developed in accor-
Plaster
dance with internationally recognized principles on standard-
C1116/C1116MSpecificationforFiber-ReinforcedConcrete
ization established in the Decision on Principles for the
C1328Specification for Plastic (Stucco) Cement
Development of International Standards, Guides and Recom-
C1787Specification for Installation of Non Metallic Plaster
mendations issued by the World Trade Organization Technical
Bases (Lath) Used with Portland Cement Based Plaster in
Barriers to Trade (TBT) Committee.
Vertical Wall Applications
E90Test Method for Laboratory Measurement of Airborne
2. Referenced Documents
Sound Transmission Loss of Building Partitions and
2
2.1 ASTM Standards:
Elements
E119Test Methods for Fire Tests of Building Construction
and Materials
1
This specification is under the jurisdiction of ASTM Committee C11 on
E492Test Method for Laboratory Measurement of Impact
GypsumandRelatedBuildingMaterialsandSystemsandisthedirectresponsibility
ofSubcommitteeC11.03onSpecificationsfortheApplicationofGypsumandOther Sound Transmission Through Floor-Ceiling Assemblies
Products in Assemblies.
Using the Tapping Machine
Current edition approved May 1, 2019. Published May 2019. Originally
2.2 ANSI Standard:
approved in 1981. Last previous edition approved in 2018 as C926–18b. DOI:
3
A108.1Specification for Installation of Ceramic Tile
10.1520/C0926-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C926−19
3. Terminology 3.2.11.5 double-up coat, n—the brown-coat plaster applied
to the scratch coat plaster before the scratch-coat plaster has
3.1 Terms shall be defined as in Terminologies C11 and
set.
C219
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C926 − 18b C926 − 19
Standard Specification for
1
Application of Portland Cement-Based Plaster
This standard is issued under the fixed designation C926; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers the requirements for the application of full thickness portland cement-based plaster for exterior
(stucco) and interior work. These requirements do not by default define a unit of work or assign responsibility for contractual
purposes, which is the purview of a contract or contracts made between contracting entities.
1.2 This specification sets forth tables for proportioning of various plaster mixes and plaster thickness.
NOTE 1—General information will be found in Annex A1. Design considerations will be found in Annex A2.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are
approximate and are provided for information purposes only.
1.3 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of
fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.
1.5 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are
approximate and are provided for information purposes only.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C25 Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime
C35 Specification for Inorganic Aggregates for Use in Gypsum Plaster
C91C91/C91M Specification for Masonry Cement
C150C150/C150M Specification for Portland Cement
C206 Specification for Finishing Hydrated Lime
C207 Specification for Hydrated Lime for Masonry Purposes
C219 Terminology Relating to Hydraulic Cement
C260C260/C260M Specification for Air-Entraining Admixtures for Concrete
C578 Specification for Rigid, Cellular Polystyrene Thermal Insulation
C595C595/C595M Specification for Blended Hydraulic Cements
C631 Specification for Bonding Compounds for Interior Gypsum Plastering
C897 Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters
C932 Specification for Surface-Applied Bonding Compounds for Exterior Plastering
C1063 Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
C1116C1116/C1116M Specification for Fiber-Reinforced Concrete
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.03 on Specifications for the Application of Gypsum and Other Products in Assemblies.
Current edition approved Aug. 1, 2018May 1, 2019. Published August 2018May 2019. Originally approved in 1981. Last previous edition approved in 2018 as
C926 – 18a.C926 – 18b. DOI: 10.1520/C0926-18B.10.1520/C0926-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C926 − 19
C1328 Specification for Plastic (Stucco) Cement
C1787 Specification for Installation of Non Metallic Plaster Bases (Lath) Used with Portland Cement Based Plaster in Vertical
Wall Applications
E90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Pa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.