ASTM B249/B249M-11
(Specification)Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
ABSTRACT
This specification establishes the general requirements common to wrought copper and copper alloy rods, bars, shapes, and forgings. Products shall be manufactured by hot working, cold working, or both, and finished by cold working, annealing, or heat treatment and straightening as identified necessary to meet the properties specified. Materials shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, diameter, length, straightness, and edge contours), mechanical (tensile strength, Rockwell hardness, elongation, and hydrogen embrittlement), electrical resistivity, chemical composition, and grain size requirements. The products shall also meet performance requirements when subjected to residual stress, mercurous nitrate, ammonia vapor, and semiguided bend tests. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.
SIGNIFICANCE AND USE
For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice
SCOPE
1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M, B140/B140M, B150/B150M, B151/B151M, B196/B196M, B283, B301/B301M, B371/B371M, B411/B411M, B441, B453/B453M, B455, B570, B927, and B967/B967M to the extent referenced therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification are prescribed in the product specification.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3.1 Within the text the SI values are given in brackets.
Note 1—Requirements for flat wire (defined as flat products up to and including 0.188 in. thick and up to 1¼ in. in width, with all surfaces rolled or drawn, without having been slit, sheared or sawed) including square, furnished in coils or straight lengths, or on spools, reels, or bucks are described by the wire Specifications B206/B206M and B272.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B249/B249M – 11
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2. Referenced Documents
2 3
1.1 This specification establishes the general requirements 2.1 ASTM Standards:
common to wrought copper and copper alloy rod, bar, shapes, B16/B16M Specification for Free-Cutting Brass Rod, Bar
and forgings which shall apply to Specifications B16/B16M, and Shapes for Use in Screw Machines
B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/ B21/B21M Specification for Naval Brass Rod, Bar, and
B139M, B140/B140M, B150/B150M, B151/B151M, B196/ Shapes
B196M, B283, B301/B301M, B371/B371M, B411/B411M, B98/B98M SpecificationforCopper-SiliconAlloyRod,Bar
B441, B453/B453M, B455, B570, B927, and B967/B967M to and Shapes
the extent referenced therein. B124/B124M Specification for Copper and Copper Alloy
1.2 The chemical composition, physical and mechanical Forging Rod, Bar, and Shapes
properties, and all other requirements not included in this B138/B138M Specification for Manganese Bronze Rod,
specification are prescribed in the product specification. Bar, and Shapes
1.3 The values stated in either SI units or inch-pound units B139/B139M Specification for Phosphor Bronze Rod, Bar,
are to be regarded separately as standard. The values stated in and Shapes
each system may not be exact equivalents; therefore, each B140/B140M Specification for Copper-Zinc-Lead (Red
system shall be used independently of the other. Combining Brass or Hardware Bronze) Rod, Bar, and Shapes
values from the two systems may result in non-conformance B150/B150M Specification for Aluminum Bronze Rod,
with the standard. Bar, and Shapes
1.3.1 Within the text the SI values are given in brackets. B151/B151M Specification for Copper-Nickel-Zinc Alloy
(Nickel Silver) and Copper-Nickel Rod and Bar
NOTE 1—Requirements for flat wire (defined as flat products up to and
B154 Test Method for Mercurous Nitrate Test for Copper
1
including0.188in.thickandupto1 ⁄4in.inwidth,withallsurfacesrolled
Alloys
or drawn, without having been slit, sheared or sawed) including square,
furnished in coils or straight lengths, or on spools, reels, or bucks are B187/B187M Specification for Copper, Bus Bar, Rod, and
described by the wire Specifications B206/B206M and B272.
Shapes and General Purpose Rod, Bar, and Shapes
B193 Test Method for Resistivity of Electrical Conductor
1.4 This standard does not purport to address all of the
Materials
safety concerns, if any, associated with its use. It is the
B194 Specification for Copper-Beryllium Alloy Plate,
responsibility of the user of this standard to establish appro-
Sheet, Strip, and Rolled Bar
priate safety and health practices and determine the applica-
B196/B196M Specification for Copper-Beryllium Alloy
bility of regulatory limitations prior to use.
Rod and Bar
B206/B206M Specification for Copper-Nickel-Zinc (Nickel
Silver) Wire and Copper-Nickel Alloy Wire
B272 Specification for Copper Flat Products with Finished
(Rolled or Drawn) Edges (Flat Wire and Strip)
B283 Specification for Copper and Copper-Alloy Die Forg-
ings (Hot-Pressed)
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
Current edition approved Jan. 1, 2011. Published February 2011. Originally
3
approved in 1951. Last previous edition approved in 2010 as B249/B249M – 10. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
DOI: 10.1520/B0249_B0249M-11. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cations SB-249 in Section II of that Code. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B249/B249M – 11
B301/B301M Specification for Free-Cutting Copper Rod, E581 Test Methods for Chemical Analysis of Manganese-
Bar, Wire, and Shapes Copper Alloys
B371/B371M Specification for Copper-Zinc-Silicon Alloy
Rod 3. Terminology
B411/B411M Specification for Copper-Nickel-Silicon Al-
3.1 Defi
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B249/B249M–10 Designation: B249/B249M – 11
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and
forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M,
B140/B140M, B150/B150M, B151/B151M, B196/B196M, B283, B301/B301M, B371/B371M, B411/B411M, B441, B453/
B453M, B455, B570, and , B927, and B967/B967M to the extent referenced therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification
are prescribed in the product specification.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3.1 Within the text the SI values are given in brackets.
1
NOTE 1—Requirements for flat wire (defined as flat products up to and including 0.188 in. thick and up to 1 ⁄4 in. in width, with all surfaces rolled
or drawn, without having been slit, sheared or sawed) including square, furnished in coils or straight lengths, or on spools, reels, or bucks are described
by the wire Specifications B206/B206M and B272.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B21/B21M Specification for Naval Brass Rod, Bar, and Shapes
B98/B98M Specification for Copper-Silicon Alloy Rod, Bar and Shapes
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B138/B138M Specification for Manganese Bronze Rod, Bar, and Shapes
B139/B139M Specification for Phosphor Bronze Rod, Bar, and Shapes
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes
B151/B151M Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B187/B187M Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B196/B196M Specification for Copper-Beryllium Alloy Rod and Bar
B206/B206M Specification for Copper-Nickel-Zinc (Nickel Silver) Wire and Copper-Nickel Alloy Wire
B272 Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
Current edition approved AprilJan. 1, 2010.2011. Published May 2010.February 2011. Originally approved in 1951. Last previous edition approved in 20092010 as
B249/B249M – 109. DOI: 10.1520/B0249_B0249M-101.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifications SB-249 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B249/B249M
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B249/B249M–10 Designation: B249/B249M – 11
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and
forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M,
B140/B140M, B150/B150M, B151/B151M, B196/B196M, B283, B301/B301M, B371/B371M, B411/B411M, B441, B453/
B453M, B455, B570, and , B927, and B967/B967M to the extent referenced therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification
are prescribed in the product specification.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3.1 Within the text the SI values are given in brackets.
1
NOTE 1—Requirements for flat wire (defined as flat products up to and including 0.188 in. thick and up to 1 ⁄4 in. in width, with all surfaces rolled
or drawn, without having been slit, sheared or sawed) including square, furnished in coils or straight lengths, or on spools, reels, or bucks are described
by the wire Specifications B206/B206M and B272.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B21/B21M Specification for Naval Brass Rod, Bar, and Shapes
B98/B98M Specification for Copper-Silicon Alloy Rod, Bar and Shapes
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B138/B138M Specification for Manganese Bronze Rod, Bar, and Shapes
B139/B139M Specification for Phosphor Bronze Rod, Bar, and Shapes
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes
B151/B151M Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B187/B187M Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B196/B196M Specification for Copper-Beryllium Alloy Rod and Bar
B206/B206M Specification for Copper-Nickel-Zinc (Nickel Silver) Wire and Copper-Nickel Alloy Wire
B272 Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
Current edition approved AprilJan. 1, 2010.2011. Published May 2010.February 2011. Originally approved in 1951. Last previous edition approved in 20092010 as
B249/B249M – 109. DOI: 10.1520/B0249_B0249M-101.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifications SB-249 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B249/B249M
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.