ASTM D5485-11
(Test Method)Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter
Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter
SIGNIFICANCE AND USE
The metal loss from corrosion is directly related to the increase in electrical resistance of the target due to the decrease in conductive cross-sectional area.
The relationship between resistance increase of metallic targets used in this test method and the amount of metal loss as reported by a uniform loss in thickness has not been determined.
This test method is used to determine the corrosive effect of combustion products from burning electrical insulations or coverings or their constituent materials or components. Corrosion is determined by the reduction of thickness of the metal on standardized targets, as measured by electrical resistance. These targets are not necessarily representative of the intended end use.
This test method is intended for use in electrical insulations or coverings material and product evaluations, for additional data to assist in design of electrical insulations or coverings products, or for development and research of electrical insulations or coverings products.
A value of the heating flux is selected to be relevant to the fire scenario being investigated (up to 100 kW/m2). Additional information for testing is given in A1.2.3.
SCOPE
1.1 This fire-test-response standard measures the corrosive effect by loss of metal from the combustion products of materials, components, or products.
1.2 This test method provides corrosion results of product and material specimens limited to a maximum size of 100 by 100 mm in area and 50 mm thick.
1.3 The results of this test method have not been investigated with respect to correlation to actual fires.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See )
1.5 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.5.1 Additional information regarding the targets, the test conditions, and test limitations are provided in the annex.
1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5485 − 11
Standard Test Method for
Determining the Corrosive Effect of Combustion Products
1
Using the Cone Corrosimeter
This standard is issued under the fixed designation D5485; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1711Terminology Relating to Electrical Insulation
D6113Test Method for Using a Cone Calorimeter to Deter-
1.1 This fire-test-response standard measures the corrosive
mineFire-Test-ResponseCharacteristicsofInsulatingMa-
effect by loss of metal from the combustion products of
terials Contained in Electrical or Optical Fiber Cables
materials, components, or products.
E176Terminology of Fire Standards
1.2 This test method provides corrosion results of product
E1354Test Method for Heat and Visible Smoke Release
and material specimens limited to a maximum size of 100 by
Rates for Materials and Products Using an Oxygen Con-
100 mm in area and 50 mm thick.
sumption Calorimeter
1.3 The results of this test method have not been investi-
IEEE/ASTM SI-10Standard for Use of the International
gated with respect to correlation to actual fires.
System of Units (SI): The Modern Metric System
2.2 Other Document:
1.4 The values stated in SI units are to be regarded as
OSHA 191.1450Occupational Exposure to Hazard Chemi-
standard. No other units of measurement are included in this
3
cals in Laboratories
standard. (See SI10)
1.5 This standard measures and describes the response of
3. Terminology
materials, products, or assemblies to heat and flame under
3.1 Definitions:
controlled conditions, but does not by itself incorporate all
3.1.1 For definitions of terms used in this test method, refer
factors required for fire hazard or fire risk assessment of the
to Terminologies E176 and D1711.
materials, products, or assemblies under actual fire conditions.
3.2 Definitions of Terms Specific to This Standard:
1.5.1 Additional information regarding the targets, the test
3.2.1 cone corrosimeter, n—equipment used to determine
conditions, and test limitations are provided in the annex.
corrosion in this test method.
1.6 Fire testing is inherently hazardous. Adequate safe-
3.2.2 corrosion-by-metal-loss, n—loss of metal of a target
guards for personnel and property shall be employed in
expressed as reduction of thickness of the target metal.
conducting these tests.
3.2.3 exposure chamber, n—enclosure in which a target is
1.7 This standard does not purport to address all of the
exposed to combustion products.
safety concerns, if any, associated with its use. It is the
3.2.4 heating flux, n—incident power per unit area that is
responsibility of the user of this standard to establish appro-
imposed externally from the heater on the specimen.
priate safety and health practices and determine the applica-
3.2.4.1 Discussion—The specimen, once ignited, is also
bility of regulatory limitations prior to use. For specific hazard
heated by its own flame.
statements, see Section 7.
3.2.5 sustained flaming, n—existence of flame on or over
2. Referenced Documents
the surface of the test specimen for periods of4sor more.
2
2.1 ASTM Standards:
3.2.5.1 Discussion—Flaming ignition of less than4sis
D618Practice for Conditioning Plastics for Testing
identified as transitory flaming or flashing.
3.2.6 target, n—detector of known electrical resistance
1
This test method is under the jurisdiction of ASTM Committee D09 on
which can lose metal through a process of corrosion when it is
Electrical and Electronic Insulating Materials and is the direct responsibility of
Subcommittee D09.17 on Fire and Thermal Properties. exposed to combustion products.
Current edition approved April 1, 2011. Published April 2011. Originally
3.3 Symbols Specific to This Standard:
approved in 1994. Last previous edition approved in 2010 as D5485–10. DOI:
10.1520/D5485-11.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Occupational Safety and Health Administration (OSHA)/U.S.
Standards volume information, refer to the standard’s Document Summary page on Departmnet of Labor, 200 Constitution Ave., NW, Washington, DC 20210, http://
the ASTM website. www.osha.gov.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5485 − 11
3.3.1 A —initial corrosion instrument reading. exposureofthetargettoacontrolledhumidityandtemperature
0
environment in a separate
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D5485–10 Designation:D5485–11
Standard Test Method for
Determining the Corrosive Effect of Combustion Products
1
Using the Cone Corrosimeter
This standard is issued under the fixed designation D5485; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This fire-test-response standard measures the corrosive effect by loss of metal from the combustion products of materials,
components, or products.
1.2 This test method provides corrosion results of product and material specimens limited to a maximum size of 100 by 100
mm in area and 50 mm thick.
1.3 The results of this test method have not been investigated with respect to correlation to actual fires.
1.4This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled
conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products,
or assemblies under actual fire conditions.
1.4.1Additional information regarding the targets, the test conditions, and test limitations are provided in the annex.
1.5ThevaluesstatedinSIunitsaretoberegardedasstandard.Nootherunitsofmeasurementareincludedinthisstandard.(See
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
(See IEEE/ASTM SI-10)
1.5 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled
conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products,
or assemblies under actual fire conditions.
1.5.1 Additional information regarding the targets, the test conditions, and test limitations are provided in the annex.
1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these
tests.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. For specific hazard statements, see Section 7.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1711 Terminology Relating to Electrical Insulation
D6113 Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials
Contained in Electrical or Optical Fiber Cables
E176 Terminology of Fire Standards
E1354 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption
Calorimeter
IEEE/ASTM SI-10 Standard for Use of the International System of Units (SI): The Modern Metric System
2.2 Other Document:
3
OSHA 191.1450 Occupational Exposure to Hazard Chemicals in Laboratories
1
This test method is under the jurisdiction of ASTM Committee D09 on Electrical and Electronic Insulating Materials and is the direct responsibility of Subcommittee
D09.21 on Fire Performance Standards.
Current edition approved MarchApril 1, 2010.2011. Published April 2010.2011. Originally approved in 1994. Last previous edition approved in 20092010 as
D5485–09.D5485–10. DOI: 10.1520/D5485-101.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Occupational Safety and Health Administration (OSHA)/U.S. Departmnet of Labor, 200 Constitution Ave., NW, Washington, DC 20210,
http://www.osha.gov.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D5485–11
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms used in this test method, refer to Terminologies E176 and D1711.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 cone corrosimeter, n—equipment used to determine corrosion in this test method.
3.2.2 corrosion-by-metal-loss, n—loss of metal o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.