ASTM F2736-13

Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness, pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and double wall corrugated polypropylene (PP) pipe. It covers nominal sizes 6 in. through 30 in. (152 mm through 762 mm).  
1.2 The corrugated polypropylene pipes governed by this standard are intended for use in non-pressure applications for sanitary sewers, storm sewers and drainage pipes. Single wall corrugated polypropylene pipe shall not be used for sanitary sewer applications.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Oct-2013
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.26 - Olefin Based Pipe

Relations

• Replaces: ASTM F2736-12 - Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe
• Effective Date: 01-Nov-2013
• Replaced By: ASTM F2736-13e1 - Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe (Withdrawn 2018)
• Effective Date: 01-Nov-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2736 −13 AnAmerican National Standard
Standard Specification for
6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated
1
Single Wall Pipe And Double Wall Pipe
This standard is issued under the fixed designation F2736; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D792 Test Methods for Density and Specific Gravity (Rela-
tive Density) of Plastics by Displacement
1.1 This specification covers requirements and test methods
D1238 Test Method for Melt Flow Rates of Thermoplastics
for materials, dimensions, workmanship, elongation,
by Extrusion Plastometer
brittleness, pipe stiffness, and markings for single wall corru-
D1505 Test Method for Density of Plastics by the Density-
gated polypropylene (PP) pipe and double wall corrugated
Gradient Technique
polypropylene (PP) pipe. It covers nominal sizes 6 in. through
D1600 Terminology forAbbreviatedTerms Relating to Plas-
30 in. (152 mm through 762 mm).
tics
1.2 The corrugated polypropylene pipes governed by this
D2122 Test Method for Determining Dimensions of Ther-
standard are intended for use in non-pressure applications for
moplastic Pipe and Fittings
sanitary sewers, storm sewers and drainage pipes. Single wall
D2321 PracticeforUndergroundInstallationofThermoplas-
corrugated polypropylene pipe shall not be used for sanitary
tic Pipe for Sewers and Other Gravity-Flow Applications
sewer applications.
D2412 Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical D2444 Test Method for Determination of the Impact Resis-
tance of Thermoplastic Pipe and Fittings by Means of a
conversions to SI units that are provided for information only
and are not considered standard. Tup (Falling Weight)
D2990 Test Methods for Tensile, Compressive, and Flexural
1.4 This standard does not purport to address all of the
Creep and Creep-Rupture of Plastics
safety concerns, if any, associated with its use. It is the
D3212 Specification for Joints for Drain and Sewer Plastic
responsibility of the user of this standard to establish appro-
Pipes Using Flexible Elastomeric Seals
priate safety and health practices and determine the applica-
D3895 Test Method for Oxidative-Induction Time of Poly-
bility of regulatory limitations prior to use.
olefins by Differential Scanning Calorimetry
D4101 Specification for Polypropylene Injection and Extru-
2. Referenced Documents
sion Materials
2
2.1 ASTM Standards:
D6992 Test Method for Accelerated Tensile Creep and
D256 Test Methods for Determining the Izod Pendulum
Creep-Rupture of Geosynthetic Materials Based on Time-
Impact Resistance of Plastics
Temperature Superposition Using the Stepped Isothermal
D618 Practice for Conditioning Plastics for Testing
Method
D638 Test Method for Tensile Properties of Plastics
F412 Terminology Relating to Plastic Piping Systems
D790 Test Methods for Flexural Properties of Unreinforced
F477 Specification for Elastomeric Seals (Gaskets) for Join-
and Reinforced Plastics and Electrical Insulating Materi-
ing Plastic Pipe
als
2.2 American Association of State Highway and transpor-
3
tation Offıcials (AASHTO) Standard:
AASHTO LRFD Bridge Design Specifications
3
1
This test method is under the jurisdiction of ASTM Committee F17 on Plastic
2.3 Transportation Research Record:
Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin
TRR No. 2028 , “Guidelines for Interpreting AASHTO
Based Pipe.
Specifications to Design or Evaluate Buried Structures
Current edition approved Nov. 1, 2013. Published December 2013. Originally
with Comprehensive Solution Methods,” 2007.
approved in 2010. Last previous edition approved in 2012 as F2736-12. DOI:
10.1520/F2736–13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from American Association of State Highway and Transportation
Standards volume information, refer to the standard’s Document Summary page on Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 2001,
the ASTM website. http://www.transportation.org
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2736−13
3. Terminology the product and having the same minimum physical properties,
may be us
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2736 − 12 F2736 − 13 An American National Standard
Standard Specification for
6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated
1
Single Wall Pipe And Double Wall Pipe
This standard is issued under the fixed designation F2736; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness,
pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and double wall corrugated polypropylene (PP)
pipe. It covers nominal sizes 6 in. through 30 in. (152 mm through 762 mm).
1.2 The corrugated polypropylene pipes governed by this standard are intended for use in non-pressure applications for sanitary
sewers, storm sewers and drainage pipes. Single wall corrugated polypropylene pipe shall not be used for sanitary sewer
applications.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
D4101 Specification for Polypropylene Injection and Extrusion Materials
D6992 Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature
Superposition Using the Stepped Isothermal Method
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
1
This test method is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin Based
Pipe.
Current edition approved Nov. 1, 2012Nov. 1, 2013. Published January 2013December 2013. Originally approved in 2010. Last previous edition approved in 20102012
as F2736-10.-12. DOI: 10.1520/F2736–12.10.1520/F2736–13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2736 − 13
3
2.2 American Association of State Highway and transportation Offıcials (AASHTO) Standard:
AASHTO LRFD Bridge Design Specifications
3
2.3 Transportation Research Record:
TRR No. 2028 , “Guidelines for Interpreting AASHTO Specifications to Design or Evaluate Buri
...