ASTM D964-03(2008)e1
(Specification)Standard Specification for Metallic Copper Powder for Use in Antifouling Paints
Standard Specification for Metallic Copper Powder for Use in Antifouling Paints
ABSTRACT
This specification covers metallic copper powder for use in antifouling paints. The pigment shall consist essentially of finely divided copper metal. The copper, and coarse particle shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers copper powder for use in antifouling paints.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D964 −03 (Reapproved 2008)
Standard Specification for
Metallic Copper Powder for Use in Antifouling Paints
This standard is issued under the fixed designation D964; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
´ NOTE—The units statement in subsection 1.2 was corrected editorially in July 2008.
1. Scope
1.1 This specification covers copper powder for use in
antifouling paints. Copper, min, (Percent) 99
Coarse particles, 325 Mesh, max, (Percent) 1.0
1.2 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
4. Sampling
conversions to SI units that are provided for information only
4.1 Two samples shall be taken at random from different
and are not considered standard.
packages from each lot, batch, day’s pack, or other unit of
2. Referenced Documents
production in a shipment. When no markings distinguishing
between units of production appear, samples shall be taken
2.1 ASTM Standards:
from different packages in the ratio of two samples for each 10
D185 Test Methods for Coarse Particles in Pigments
000 lb (5000 kg), except that for shipments of less than 10 000
D283 Test Methods for Chemical Analysis of Cuprous
lb two samples shall be taken. At the option of the purchaser,
Oxide and Copper Pigments
the samples may be tested separately or after blending in equal
3. Composition
quantities the samples from the same production unit to form a
3.1 The pigment shall consist essentially of finely divided composite sample.
copper metal and shall conform to the following requirements:
5. Test Methods
This specification is under the jurisdiction of ASTM Committee D01 on Paint
5.1 Tests shall be conducted in accordance with the follow-
and Related Coatings, Materials, andApplications and is the direct responsibil
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D 964 – 03 (Reapproved 2008)
Designation:D964 – 65 (Reapproved 1996)
Standard Specification for
Metallic Copper Powder for Use in Antifouling Paints
This standard is issued under the fixed designation D 964; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
´ NOTE—Keywords were added editorially in May 1996.
—The units statement in subsection 1.2 was corrected editorially in July 2008.
1. Scope
1.1 This specification covers copper powder for use in antifouling paints.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2.1 ASTM Standards:
D 185Test Methods for Coarse Particles in Pigments, Pastes, and Paints Test Methods for Coarse Particles in Pigments
D 283 Test Methods for Chemical Analysis of Cuprous Oxide and Copper Pigments
3. Composition
3.1 The pigment shall consist essentially of finely divided copper metal and shall conform to the following requirements:
Copper, min, %
Copper, min, (Percent) 99
Coarse particles, max, % 1.0
Coarse particles, 325 Mesh, max, (Percent) 1.0
4. Sampling
4.1 Two samples shall be taken at random from different packages from each lot, batch, day’s pack, or other unit of production
in a shipment. When no markings distinguishing between units of production appear, samples shall be taken from different
packages in the ratio of two samples for each 10 000 lb (5000 kg), except that for shipments of less than 10 000 lb two samples
shall be taken.At the option of the purchaser, the samples may be tested separately or after blending in equal quantities the samples
from the same production unit to form a composite sample.
5. Test Methods
5.1 Tests shall be conducted in accordan
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.