iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6757-05

(Specification)

Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing

Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing

SCOPE
1.1 This specification covers (1) inorganic fiber-reinforced organic felt underlayment and ( 2) inorganic fiber-based felt for use as underlayment with steep-slope roofing products. The intent of this specification is to provide criteria for producing and evaluating underlayments with a significantly reduced tendency to wrinkle before or after the installation of steep roofing products.
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
31-Dec-2004
ICS
91.060.20 - Roofs
Technical Committee
D08 - Roofing and Waterproofing
Drafting Committee
D08.02 - Steep Roofing Products and Assemblies
Current Stage
Ref Project

Relations

Replaces
ASTM D6757-04a - Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing
Effective Date
01-Jan-2005
Replaced By
ASTM D6757-07 - Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing
Effective Date
01-May-2007

Buy Standard

ASTM D6757-05 - Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope RoofingASTM D6757-05 - Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing
PreviousNext
Technical specification
ASTM D6757-05 - Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 6757 – 05
Standard Specification for
Underlayment Felt Containing Inorganic Fibers Used in
1
Steep-Slope Roofing
This standard is issued under the fixed designation D 6757; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope F 1087 Test Method for Linear Dimensional Stability of a
Gasket Material to Moisture
1.1 This specification covers (1) inorganic fiber-reinforced
organic felt underlayment and (2) inorganic fiber-based felt for
3. Terminology
use as underlayment with steep-slope roofing products. The
3.1 Definitions—For definitions of terms used in this speci-
intent of this specification is to provide criteria for producing
fication, refer to Terminology D 1079.
and evaluating underlayments with a significantly reduced
tendency to wrinkle before or after the installation of steep
4. Classification
roofing products.
4.1 Organicfeltsthatarereinforcedwithinorganicfibersare
1.2 The values stated in SI units are to be regarded as the
covered by this specification.
standard. The values in parentheses are for information only.
4.2 Inorganic fiber-based asphaltic and nonasphaltic felts
1.3 The following safety hazards caveat pertains only to the
are covered by this specification.
test method portion, Section 8, of this specification: This
standard does not purport to address all of the safety concerns,
5. Materials and Manufacture
if any, associated with its use. It is the responsibility of the user
5.1 In the process of manufacture, a single thickness of
of this standard to establish appropriate safety and health
inorganic mat or organic felt that is reinforced with inorganic
practices and determine the applicability of regulatory require-
fibers shall be uniformly saturated or coated.
ments prior to use.
6. Performance Requirements
2. Referenced Documents
6.1 The material shall conform to the physical requirements
2
2.1 ASTM Standards:
prescribed in Table 1.
D 146 Test Methods for Sampling and Testing Bitumen-
6.2 The finished product shall not crack nor be so sticky as
Saturated Felts and Woven Fabrics for Roofing and Wa-
to cause tearing or other damage upon being unrolled at
terproofing
temperatures between –1 and 60°C (30 and 140°F). The
D 228 Test Methods for Sampling, Testing, andAnalysis of
finished product shall pass the water shower exposure test in
Asphalt Roll Roofing, Cap Sheets, and Shingles Used in
accordance with 8.1.4, indicating resistance to liquid water
Roofing and Waterproofing
transmission.
D 1079 Terminology Relating to Roofing, Waterproofing,
and Bituminous Materials
7. Dimensions, Masses, Workmanship, Finish, and
D 3462 SpecificationforAsphaltShinglesMadefromGlass
Appearance
Felt and Surfaced with Mineral Granules
7.1 Dimensions and masses to be agreed upon between
D 4869 Specification for Asphalt-Saturated Organic Felt
buyer and seller.
Underlayment Used in Steep Slope Roofing
7.2 The finished material shall be free of visible external
defects, such as holes, ragged or untrue edges, breaks, cracks,
1
tears, bulges, and indentations.
This specification is under the jurisdiction of ASTM Committee D08 on
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02
on Prepared Roofing, Shingles, and Siding Materials. 8. Sampling and Test Methods
Current edition approved Jan. 1, 2005. Published January 2005. Originally
8.1 Sample the material and determine the properties enu-
approved in 2002. Last previous edition approved in 2004 as D 6757 – 04a.
2
merated in this specification in accordance with Test Methods
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D 146.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D6757–05
TABLE 1 Performance Requirements
8.2.2 Precision and Bias—To be determined.
Tear strength, min at 23 6 2°C, (73 6 4°F), 4.0, (0.88) (in any direction)
N, (lbf)
9. Inspection
Pliability at 23 6 2°C, (73 6 4°F), the ten strips pass
tested shall not crack when bent 90° 9.1 Inspection of the material shall be made as agreed upon
at a uniform speed over a 19 mm (0.75 in.)
betweenthepurchaserandthesupplierasapartofthepurchase
radius corner in 2 s
contract.
Behavior (loss) on heating at 105°C (221°F) 4
for 5 h, max, %
Liquid water transmission test pass
10. Rejection and Resubmittal
Dimensional stability, 1.65
low humidity to high humidity, 10.1 F
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7897-18(2023)(Practice)
Standard Practice for Laboratory Soiling and Weathering of Roofing Materials to Simulate Effects of Natural Exposure on Solar Reflectance and Thermal Emittance

SIGNIFICANCE AND USE
5.1 The solar reflectance of a building envelope surface affects surface temperature and near-surface ambient air temperature. Surfaces with low solar reflectance absorb a high fraction of the incoming solar energy. Sunlight absorbed by a roof or by other building envelope surfaces can be conducted into the building, increasing cooling load and decreasing heating load in a conditioned building, or raising indoor temperature in an unconditioned building. It can also warm the outside air by convection. Determination of solar reflectance can help designers and consumers choose appropriate materials for their buildings and communities.  
5.1.1 The solar reflectance of a new building envelope surface often changes within one to two years through deposition and retention of soot and dust; microbiological growth; exposure to sunlight, precipitation, and dew; and other processes of soiling and weathering. For example, light-colored “cool” envelope surfaces with high initial reflectance can experience substantial reflectance loss as they are covered with dark soiling agents. Current product rating programs require roofing manufacturers to report values of solar reflectance and thermal emittance measured after three years of natural exposure (2, 3). A rapid laboratory process for soiling and weathering that simulates the three-year-aged radiative properties of roof and other building envelope surface materials expedites the development, testing, and introduction to market of such products.  
5.2 Thermal emittance describes the efficiency with which a surface exchanges thermal radiation with its environment. High thermal emittance enhances the ability of a surface to stay cool in the sun. The thermal emittance of a bare metal surface is initially low, and often increases as it is soiled or oxidized (4). The thermal emittance of a typical non-metal surface is initially high, and remains high after soiling (5).  
5.3 This practice allows measurement of the solar reflectance a...
SCOPE
1.1 Practice D7897 applies to simulation of the effects of field exposure on the solar reflectance and thermal emittance of roof surface materials including but not limited to field-applied coatings, factory-applied coatings, single-ply membranes, modified bitumen products, shingles, tiles, and metal products. The solar reflectance and thermal emittance of roof surfacing materials can be changed by exposure to the outdoor environment. These changes are caused by three factors: deposition and retention of airborne pollutants, microbiological growth, and changes in physical or chemical properties. This practice applies to simulation of changes in solar reflectance and thermal emittance induced by deposition and retention of airborne pollutants and, to a limited extent, changes caused by microbiological growth.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D6754/D6754M-23(Specification)
Standard Specification for Ketone Ethylene Ester Based Sheet Roofing

SCOPE
1.1 This specification covers flexible sheet made from ketone ethylene ester (KEE) as the primary polymer intended for use in single-ply roofing membrane exposed to the weather. The sheet shall be reinforced with fabric.  
1.2 In-place roof system design criteria, such as fire resistance, field-seaming strength, material compatibility, uplift resistance, in-situ shrinkage, among others, are factors that must be considered but are beyond the scope of this specification.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 The following precautionary caveat pertains to the test methods portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D41/D41M-11(2023)(Specification)
Standard Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing

ABSTRACT
This specification covers asphaltic primer suitable for use with asphalt in roofing, dampproofing, and waterproofing below or above ground level, for application to concrete, masonry, metal, and asphalt surfaces. Asphalt primer shall be classified as Type I and Type II. To determine the properties of the asphalt primer, the following test methods shall be performed: furol viscosity; distillation; penetration; and matter soluble in trichloroethylene.
SCOPE
1.1 This specification covers asphaltic primer suitable for use with asphalt in roofing, dampproofing, and waterproofing below or above ground level, for application to concrete, masonry, metal, and asphalt surfaces.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6757/D6757M-18(2023)(Specification)
Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing

ABSTRACT
This specification covers inorganic fiber-reinforced organic felt, and inorganic fiber-based asphaltic and nonasphaltic felt underlayments for use as underlayment with steep-slope roofing products. The intent of this specification is to provide criteria for producing and evaluating underlayments with a significantly reduced tendency to wrinkle before or after the installation of steep roofing products. Materials shall be sampled and tested suitably to examine their conformance with performance requirements such as tear strength, pliability, behavior on heating, liquid water transmission, dimensional stability at low to high humidity conditions, and elongation.
SCOPE
1.1 This specification covers (1) inorganic fiber-reinforced organic felt underlayment, and (2) inorganic fiber-based felt for use as underlayment with steep-slope roofing products. The intent of this specification is to provide criteria for producing and evaluating underlayments with a significantly reduced tendency to wrinkle before or after the installation of steep roofing products.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6694/D6694M-15(2023)(Specification)
Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems

ABSTRACT
This specification covers a liquid-applied solvent dispersed elastomeric coating used as a roofing membrane for spray polyurethane foam (SPF) insulation whose principal polymer in the dispersion contains more than 95 % silicone. The product, as manufactured, shall be in liquid form for application to SPF surfaces by brushing, squeegeeing, rolling, or spraying. The product shall be composed of dispersion containing as the principal polymer more than 95 % silicone polymers to which various pigments and other additives have been added to give the required physical properties. Liquid properties like viscosity, volume solids, and weight solids shall be determined after conducting different tests. Physical properties of cured silicone coating like elongation, tensile strength, permeance, accelerated weathering, adhesion, tear resistance, and low-temperature flexibility shall be determined after a series of tests.
SCOPE
1.1 This specification covers a liquid-applied solvent dispersed elastomeric coating used as a roofing membrane for spray polyurethane foam (SPF) insulation whose principal polymer in the dispersion contains more than 95 % silicone.  
1.2 This specification does not provide guidance for application.  
1.3 The following precautionary caveat pertains only to the test method portions, Sections 5 and 6.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7655/D7655M-12(2022)(Classification)
Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems

SIGNIFICANCE AND USE
4.1 The wind resistance of ballasted membrane roof systems is determined largely by the size and weight of the ballast used. ANSI/SPRI RP-4 provides a method for the wind design of ballasted single-ply membrane roof systems and includes specific guidelines for the size and weight of aggregate used as ballast. The aggregate size classifications provided in this standard are intended for use with the guidelines provided in ANSI/SPRI RP-4 in designing the wind resistance of aggregate ballasted single-ply membrane roof systems.  
4.2 The aggregate size classifications provided in this classification are intended to provide a basis of compliance for contract documents that specify certain aggregate sizes for use on ballasted membrane systems.
SCOPE
1.1 This classification defines the aggregate size designations and ranges in mechanical analyses for standard sizes of aggregate used as ballast for membrane roof systems.  
1.2 The text of this classification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 With regard to sieve sizes and the size of aggregate as determined by the use of testing sieves, the values in inch-pound units are shown for the convenience of the user; however, the standard sieve designations shown in parentheses are the standard values as stated in Specification E11.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6382/D6382M-99(2022)(Practice)
Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material

SIGNIFICANCE AND USE
5.1 Dynamic mechanical analysis provides a measure of the rheological properties of roofing and waterproofing membrane materials.  
5.2 Thermogravimetry is used to characterize the thermal stability of roofing and waterproofing membrane materials under the specific temperature program and gaseous atmosphere conditions selected for the analysis.  
5.3 Both dynamic mechanical analysis and thermogravimetry are used to evaluate the effect of either laboratory-simulated or in-service exposure on roofing and waterproofing membrane materials.  
5.4 Both dynamic mechanical analysis and thermogravimetry can be applied to asphalt shingles. However, their application to asphalt shingles is beyond the scope of this practice, which is limited to low-slope membrane materials at this time.  
5.5 This practice can be useful in the development of performance criteria for roofing and waterproofing membrane materials.
SCOPE
1.1 This practice covers test procedures and conditions that are applicable when Test Methods D5023, D5024, D5026, D5279, and D5418 are used for conducting dynamic mechanical analysis of roofing and waterproofing membrane material in three-point bending, compression, tension, torsion, and dual cantilever modes, respectively. The specific method is selected by the analyst and depends on the membrane material and the operating principles of the individual instrument used for the analysis.  
1.2 This practice covers test procedures and conditions that are applicable when Test Method E1131 is used for conducting thermogravimetry of roofing and waterproofing membrane material.  
1.3 Membrane materials include bituminous built-up roofing, polymer-modified bitumen sheets, vulcanized rubbers, non-vulcanized polymeric sheets, and thermoplastics. The membrane materials can be either nonreinforced or reinforced.  
1.4 This practice is applicable to new membrane materials received from the supplier, those exposed artificially in the laboratory or outdoors on an exposure rack, and those sampled from field installations.  
1.5 This practice contains notes which are explanatory and are not part of the mandatory requirements of this practice.  
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7954/D7954M-22a(Practice)
Standard Practice for Moisture Surveying of Roofing and Waterproofing Systems Using Nondestructive Electrical Impedance Scanners

SIGNIFICANCE AND USE
5.1 Excess moisture trapped in roofing or waterproofing systems can adversely affect performance and lead to premature failure of roofing or waterproofing systems and its components. It also reduces thermal resistance, resulting in reduced energy efficiency and inflated energy costs. Impedance scans can be effective in identifying concealed and entrapped moisture within roofing or waterproofing systems.  
5.2 This practice is intended to be used at various stages of the roofing and waterproofing system’s life such as: during or at completion of installation of roofing or waterproofing system to determine if there was moisture intrusion into the roofing or waterproofing system or underlying materials; at regular intervals as part of a preventative maintenance program; and to aid in condition assessment, or before replacement or repair work, or combinations thereof, to assist in determining the extent of work and replacement materials.  
5.3 This practice alone does not determine the cause of moisture infiltration into roofing or waterproofing systems; however, it can be used to help tracing excess moisture to the point of ingress.
SCOPE
1.1 This practice applies to techniques that use nondestructive electrical impedance (EI) scanners to locate moisture and evaluate the comparative moisture content within insulated low-slope roofing and waterproofing systems.  
1.2 This practice is applicable to roofing and waterproofing systems wherein insulation is placed above the deck and positioned underneath and in contact with electrically nonconductive single-ply or built-up roofing and waterproofing membranes and systems such as coal tar, asphalt, modified bitumen, thermoplastics, spray polyurethane foam, and similar electrically nonconductive membrane materials. This practice is also applicable to roofing and waterproofing systems without insulation placed above moisture absorbing decks such as wood, concrete, or gypsum, that are in contact with single-ply or built-up roofing and waterproofing membranes as described above.  
1.3 This practice is applicable to roofing and waterproofing systems incorporating electrically nonconductive rigid board insulation made from materials such as organic fibers, perlite, cork, fiberglass, wood-fiber, polyisocyanurate, polystyrene, phenolic foam, composite boards, gypsum substrate boards, and other electrically nonconductive roofing and waterproofing systems such as spray-applied polyurethane foam.  
1.4 This practice is not appropriate for all combinations of materials used in roofing and waterproofing systems.  
1.4.1 Metal and other electrically conductive surface coverings and near-surface embedded metallic components are not suitable for surveying with impedance scanners because of the electrical conductivity of these materials.  
1.4.2 This practice is not appropriate for use with black EPDM, any membranes containing black EPDM, or black EPDM coatings because black EPDM gives false positive readings.  
1.4.3 Aluminum foil on top-faced insulation, roofing, or waterproofing membranes gives a false positive reading and is not suitable for surveying with impedance scanners; however, liquid-applied aluminum pigmented emulsified asphalt-based coatings shall not normally affect impedance scanner readings.
1.4.3.1 This practice is not appropriate for use with aluminium foil faced modified bitumen membranes, as the electrical conductivity of the aluminium foil surface can give false positive readings.  
1.4.4 While their overburden remains in place, this practice is not appropriate for use with inverted roof membrane assemblies (IRMAs) or protected roof assemblies (PRMAs), which contain above the deck waterproof membrane and overburden that may include insulation, drainage components, pavers, aggregate, ballast, vegetation, or combinations thereof, because the impedance scanner will not differentiate between above and below the membrane moisture.  
1.4.5 S...

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D8257/D8257M-22(Specification)
Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing

SCOPE
1.1 This specification addresses mechanically attached polymeric roof underlayment used in steep slope roofing.  
1.2 The objective of this specification is to provide a finished product that will be used as a water-shedding underlayment layer on steep sloped roofs prior to and after installation of the primary roof covering.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6383/D6383M-99(2021)(Practice)
Standard Practice for Time-to-Failure (Creep-Rupture) of Adhesive Joints Fabricated from EPDM Roof Membrane Material

SIGNIFICANCE AND USE
5.1 An important factor affecting the performance of seams of EPDM membranes is their ability to remain bonded over the membrane's expected service life. Time-to-failure tests provide a means of characterizing the behavior of joints under constant load over time.
Note 1: Table 1 is based on the results of an industry government consortium study on creep-rupture resistance (time-to-failure) of EPDM adhesive joints.4,5 Referral to Footnotes 4 and 5 provides typical time-to-failure data, developed under the conditions in Table 1, for EPDM joints fabricated in the laboratory with non-reinforced EPDM roof membrane material, butyl-based tapes, and liquid adhesives. It is noted that the peel load specified in this practice is 9.8 N [2.2 lbf]. The peel load under which the tests described in Footnotes 4 and 5 were conducted was 9.3 N [2.1 lbf]. A load of 9.8 N [2.2 lbf] corresponds to 1 kgf [2.2 lbf], and dead weights of 1-kg [2.2-lbm] mass are available through laboratory equipment supply houses. Similarly, a load of 29.4 N [6.6 lbf] corresponds to a dead weight of 3-kg [6.6-lbm] mass.  
5.2 Time-to-failure tests complement other mechanical tests such as strength for characterizing joints of EPDM roof membranes, and can be incorporated in specifications for adhesives for joining EPDM roof membrane material.  
5.3 This practice, which is specific to EPDM joints, complements Test Method D5405/D5405M that provides general requirements for the preparation and creep-rupture testing of joints fabricated from any nonbituminous organic roof membrane material.  
5.4 Laboratory experience in conducting time-to-failure tests of joints EPDM roof membranes has shown that specimens are less creep-resistant under peel loading than under shear loading. Consequently, the majority of the tests stipulated in this practice are performed under peel loading.  
5.5 This practice does not develop time-to-failure data on all environmental conditions to which EPDM adhesive seams can be subjec...
SCOPE
1.1 This practice covers sample preparation temperatures, test parameters, and specimen exposure conditions that are applicable when Test Method D5405/D5405M is used for conducting time-to-failure (creep-rupture) tests of adhesive joints fabricated from ethylene-propylene-diene terpolymer (EPDM) roof membrane material.  
1.2 This practice is applicable to joints fabricated in the laboratory from EPDM roof membrane materials and adhesives received from suppliers, and to joints prepared from EPDM seams sampled from field installations.  
1.3 The joints are bonded using preformed tape or liquid-based adhesives, and EPDM roof membrane materials that are non-reinforced, fabric- or scrim-reinforced, and fabric backed. Primers are also used as recommended for the specific adhesive.  
1.4 This practice contains notes that are explanatory and are not part of the mandatory requirements of this practice.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off