ASTM A724/A724M-09(2013)
(Specification)Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels
Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels
ABSTRACT
This specification covers standard requirements for three grades of carbon-manganese-silicon steel, designated Grades A, B, and C. Grade C may be produced with a boron addition. The plates shall be quenched and tempered and shall be intended for welded-layered pressure vessels. The steel shall be killed and shall conform to the fine austenitic grain size requirement. Heat and product analyses shall be performed wherein the material shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum, vanadium, and boron. The steel plate shall undergo tension test and shall conform to tensile requirements such as tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification2 covers three grades of carbon-manganese-silicon steel, designated Grades A, B, and C. Grade C may be produced with a boron addition. The plates are quenched and tempered and are intended for welded-layered pressure vessels.
1.2 The maximum thickness of plates supplied under this specification is limited only by the capability of the chemical composition to meet the specified mechanical requirements. However, current practice normally limits the maximum thickness to 7/8 in. [22 mm] for Grades A and B, and to 2 in. [50 mm] for Grade C.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A724/A724M −09 (Reapproved 2013)
Standard Specification for
Pressure Vessel Plates, Carbon-Manganese-Silicon Steel,
Quenched and Tempered, for Welded Pressure Vessels
This standard is issued under the fixed designationA724/A724M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. General Requirements and Ordering Information
1.1 This specification covers three grades of carbon- 3.1 Material supplied to this material specification shall
manganese-silicon steel, designated GradesA, B, and C. Grade conform to Specification A20/A20M. These requirements out-
C may be produced with a boron addition. The plates are line the testing and retesting methods and procedures, permit-
quenched and tempered and are intended for welded-layered ted variations in dimensions and weight, quality and repair of
pressure vessels. defects, marking, loading, and ordering information.
1.2 The maximum thickness of plates supplied under this 3.2 In addition to the basic requirements of this
specification is limited only by the capability of the chemical specification, certain supplementary requirements are available
composition to meet the specified mechanical requirements. when additional control, testing, or examination is required to
However, current practice normally limits the maximum thick- meet end use requirements. The purchaser is referred to the
nessto ⁄8in.[22mm]forGradesAandB,andto2in.[50mm] listed supplementary requirements in this specification and to
for Grade C. the detailed requirements in Specification A20/A20M.
1.3 The values stated in either inch-pound units or SI units 3.3 If the requirements of this specification are in conflict
are to be regarded separately as standard. Within the text, the with the requirements of Specification A20/A20M, the require-
SI units are shown in brackets. The values stated in each ments of this specification shall prevail.
system are not exact equivalents; therefore, each system must
4. Manufacture
be used independently of the other. Combining values from the
two systems may result in nonconformance with the specifi- 4.1 Steelmaking Process—The steel shall be killed and shall
conform to the fine austenitic grain size requirement of
cation.
Specification A20/A20M.
1.4 This international standard was developed in accor-
dance with internationally recognized principles on standard-
5. Heat Treatment
ization established in the Decision on Principles for the
5.1 All plates shall be quenched from a temperature in the
Development of International Standards, Guides and Recom-
range from 1600 to 1700°F [870 to 925°C]. Grades A and B
mendations issued by the World Trade Organization Technical
shall then be tempered at not less than 1100°F [595°C], and
Barriers to Trade (TBT) Committee.
Grade C shall then be tempered at not less than 1150°F
[620°C]. The tempering soaking time shall be not less than ⁄2
2. Referenced Documents
h.
2.1 ASTM Standards:
A20/A20M SpecificationforGeneralRequirementsforSteel
6. Chemical Composition
Plates for Pressure Vessels
6.1 The steel shall conform to the requirements as to
chemical composition prescribed in Table 1.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
7. Mechanical Properties
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.11 on Steel Plates for Boilers and Pressure Vessels.
7.1 Tension Test Requirements:
Current edition approved Oct. 1, 2013. Published October 2013. Originally
7.1.1 The material as represented by the tension test speci-
approved in 1975. Last previous edition approved in 2009 as A724/A724M – 09.
mens shall conform to the requirements given in Table 2.
DOI: 10.1520/A0724_A0724M-09R13.
7.1.2 For nominal plate thicknesses of ⁄4 in. [20 mm] and
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
cation SA-724/SA-724M in Section II of that Code.
under, the 1 ⁄2-in. [40-mm] wide rectangular specimen may be
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.