ASTM C1063-14c
(Specification)Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
ABSTRACT
This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases—expanded metal lath and wire laths; accessories—steel, PVC plastic, zinc alloy, and cornerite; channels—external corner reinforcement and foundation weep screed; wire; rod and strap hangers; clips; fasteners—nails and screws. Hangers and cold-rolled channel main runner shall conform to the allowable spacing and spans, respectively. The following methods are discussed: installation of hangers for suspended ceilings under wood constructions, attachment of hangers to main runners, installation of main runners, installation of cross furring, metal furring for walls, lapping of metal plaster bases, spacing of attachments for metal plaster bases, application of metal plaster bases, and application of accessories.
SCOPE
1.1 This specification covers the minimum requirements for lathing and furring for the application of exterior and interior portland cement-based plaster as in Specification C926 or Specification C841.
1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.
1.3 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable requirements of Test Method E90.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1063 −14c
StandardSpecification for
Installation of Lathing and Furring to Receive Interior and
1
Exterior Portland Cement-Based Plaster
This standard is issued under the fixed designation C1063; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* C11 Terminology Relating to Gypsum and Related Building
Materials and Systems
1.1 This specification covers the minimum requirements for
C841 Specification for Installation of Interior Lathing and
lathing and furring for the application of exterior and interior
Furring
portland cement-based plaster as in Specification C926 or
C847 Specification for Metal Lath
Specification C841.
C926 Specification for Application of Portland Cement-
1.2 Where a fire resistance rating is required for plastered
Based Plaster
assembliesandconstructions,detailsofconstructionshallbein
C933 Specification for Welded Wire Lath
accordance with reports of fire tests of assemblies that have
C954 SpecificationforSteelDrillScrewsfortheApplication
met the requirements of the fire rating imposed.
of Gypsum Panel Products or Metal Plaster Bases to Steel
1.3 Where a specific degree of sound control is required for Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in
Thickness
plastered assemblies and constructions, details of construction
shallbeinaccordancewithofficialreportsoftestsconductedin C1002 Specification for Steel Self-Piercing Tapping Screws
for the Application of Gypsum Panel Products or Metal
recognized testing laboratories in accordance with the appli-
cable requirements of Test Method E90. Plaster Bases to Wood Studs or Steel Studs
C1032 Specification for Woven Wire Plaster Base
1.4 The values stated in inch-pound units are to be regarded
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
as standard. The values given in parentheses are mathematical
Compounds and Chlorinated Poly(Vinyl Chloride)
conversions to SI units that are provided for information only
(CPVC) Compounds
and are not considered standard.
D4216 Specification for Rigid Poly(Vinyl Chloride) (PVC)
and Related PVC and Chlorinated Poly(Vinyl Chloride)
2. Referenced Documents
(CPVC) Building Products Compounds
2
2.1 ASTM Standards:
E90 Test Method for Laboratory Measurement of Airborne
A641/A641M Specification for Zinc–Coated (Galvanized)
Sound Transmission Loss of Building Partitions and
Carbon Steel Wire
Elements
A653/A653M Specification for Steel Sheet, Zinc-Coated
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
3. Terminology
by the Hot-Dip Process
3.1 Definitions—For definitions relating to Ceilings and
B69 Specification for Rolled Zinc
Walls, see Terminology C11.
B221 Specification forAluminum andAluminum-Alloy Ex-
truded Bars, Rods, Wire, Profiles, and Tubes 3.2 Definitions of Terms Specific to This Standard:
3.2.1 barrier wall, n—typeofwallsystemthatisintendedto
block or interrupt the movement of water to the interior.
1
This specification is under the jurisdiction of ASTM Committee C11 on
3.2.2 building enclosure, n—system of building assemblies
Gypsum and Related Building Materials and Systems and is the direct responsibility
and materials designed and installed in such a manner as to
ofSubcommitteeC11.03onSpecificationsfortheApplicationofGypsumandOther
provide a barrier between different environments.
Products in Assemblies.
CurrenteditionapprovedJune1,2014.PublishedJuly2014.Originallyapproved
3.2.3 control joint, n—a joint that accommodates movement
in 1986. Last previous edition approved in 2014 as C1063 – 14b. DOI: 10.1520/
of plaster shrinkage and curing along predetermined, usually
C1063-14C.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
straight, lines.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3.2.4 drainage plane, n—surface between the back of the
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. cladding and the front of the water barrier which resists liquid
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1063−14c
moisture infiltration and provides for gravitational flow to a
collection or exhaust location.
3.2.5 drainage space, n—volumetric area that allows the
gravitational flow of liquid moisture to a collection or exhaust
location.
3.2.6 drainage wall, n—a wall system in which the cladding
providesasu
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1063 − 14b C1063 − 14c
Standard Specification for
Installation of Lathing and Furring to Receive Interior and
1
Exterior Portland Cement-Based Plaster
This standard is issued under the fixed designation C1063; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers the minimum requirements for lathing and furring for the application of exterior and interior
portland cement-based plaster as in Specification C926 or Specification C841.
1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in
accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.
1.3 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall
be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable
requirements of Test Method E90.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A641/A641M Specification for Zinc–Coated (Galvanized) Carbon Steel Wire
A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process
B69 Specification for Rolled Zinc
B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C841 Specification for Installation of Interior Lathing and Furring
C847 Specification for Metal Lath
C926 Specification for Application of Portland Cement-Based Plaster
C933 Specification for Welded Wire Lath
C954 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs
from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness
C1002 Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster
Bases to Wood Studs or Steel Studs
C1032 Specification for Woven Wire Plaster Base
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D4216 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC)
Building Products Compounds
E90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.03 on Specifications for the Application of Gypsum and Other Products in Assemblies.
Current edition approved April 1, 2014June 1, 2014. Published May 2014July 2014. Originally approved in 1986. Last previous edition approved in 2014 as
C1063 – 14a.C1063 – 14b. DOI: 10.1520/C1063-14B.10.1520/C1063-14C.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1063 − 14c
3. Terminology
3.1 Definitions—For definitions relating to Ceilings and Walls, see Terminology C11.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 barrier wall, n—type of wall system that is intended to block or interrupt the movement of water to the interior.
3.2.2 building enclosure, n—system of building assemblies and materials designed and installed in such a manner as to provide
a barrier between different environments.
3.2.3 control joint, n—a joint that accommodates movement of plaster shrinkage and curing along predetermined, usually
straight, lines.
3.2.4 drainage pla
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.