ASTM C1047-10a
(Specification)Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
ABSTRACT
This specification covers accessories used in conjunction with assemblies of gypsum wallboard and gypsum veneer base to protect edges and corners and to provide architectural features. Steel accessories and steel components of accessories manufactured from steel and paper in combination shall be manufactured from zinc-coated cold-roll sheet steel before application of coating. Phosphatizing or other surface treatments may be used to ensure compatibility and bond. Paper components of accessories manufactured from steel and paper in combination shall comply with requirements for thickness, tensile strength, dimensional stability, and bond of joint tape to joint compound. Accessories shall be free of twist or camber of a degree that will prevent their use in the assembly for which they are intended. Edges of accessories shall be free of burrs and sharp edges.
SCOPE
1.1 This specification covers accessories used in conjunction with assemblies of gypsum wallboard and gypsum veneer base to protect edges and corners and to provide architectural features (see Fig. 1).
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1047 −10a
StandardSpecification for
Accessories for Gypsum Wallboard and Gypsum Veneer
1
Base
This standard is issued under the fixed designation C1047; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* D3678 Specification for Rigid Poly(Vinyl Chloride) (PVC)
Interior-Profile Extrusions
1.1 This specification covers accessories used in conjunc-
D3935 Specification for Polycarbonate (PC) Unfilled and
tion with assemblies of gypsum wallboard and gypsum veneer
Reinforced Material
base to protect edges and corners and to provide architectural
D4549 Classification System and Basis for Specification for
features (see Fig. 1).
Polystyrene and Rubber-Modified Polystyrene Molding
1.2 The values stated in inch-pound units are to be regarded
and Extrusion Materials (PS)
as standard. The values given in parentheses are mathematical
D5927 Classification System for Thermoplastic Polyester
conversions to SI units that are provided for information only
(TPES) Injection and Extrusion Materials Based on ISO
and are not considered standard.
Test Methods
D6386 Practice for Preparation of Zinc (Hot-Dip Galva-
2. Referenced Documents
nized) Coated Iron and Steel Product and Hardware
2
2.1 ASTM Standards:
Surfaces for Painting
A463/A463M Specification for Steel Sheet, Aluminum-
Coated, by the Hot-Dip Process
3. Terminology
A653/A653M Specification for Steel Sheet, Zinc-Coated
3.1 Definitions:
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
3.1.1 Definitions shall be in accordance with Terminology
by the Hot-Dip Process
C11.
A879/A879M Specification for Steel Sheet, Zinc Coated by
3.2 Definitions of Terms Specific to This Standard:
the Electrolytic Process for Applications Requiring Des-
3.2.1 accessories, n—cornerbeads, edge trims, and control
ignation of the Coating Mass on Each Surface
joints, such as casing beads, bull noses, and stops.
B69 Specification for Rolled Zinc
B117 Practice for Operating Salt Spray (Fog) Apparatus
3.2.2 control joint, n—a formed product used for designed
C11 Terminology Relating to Gypsum and Related Building
or required separations between adjacent surfaces of gypsum
Materials and Systems
boards or gypsum veneer base.
C475/C475M Specification for Joint Compound and Joint
3.2.3 cornerbead, n—a formed metal, plastic, or metal and
Tape for Finishing Gypsum Board
paper angle for outside corners of gypsum boards or gypsum
C587 Specification for Gypsum Veneer Plaster
veneer base.
D1788 Specification for Rigid Acrylonitrile-Butadiene-
3
Styrene(Abs) Plastics (Withdrawn 1988) 3.2.4 edge trim, n—typically “J”- or “L”-shaped strip, as
shown in Fig. 1, formed of metal, plastic, or metal and paper to
cover exposed ends or edges of gypsum board or gypsum
1
This specification is under the jurisdiction of ASTM Committee C11 on
veneer base.
Gypsum and Related Building Materials and Systems and is the direct responsibility
of Subcommittee C11.02 on Specifications and Test Methods for Accessories and
3.2.5 flange, n—that portion of the accessory used for the
Related Products.
attachment to gypsum wallboard, gypsum veneer base, or a
Current edition approved Oct. 1, 2010. Published November 2010. Originally
approved in 1992. Last previous edition approved in 2010 as C1047–10. DOI: framing member.
10.1520/C1047-10a.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4. Materials and Manufacture
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4.1 Steel accessories and steel components of accessories
the ASTM website.
3
manufactured from steel and paper in combination shall be
The last approved version of this historical standard is referenced on
www.astm.org. manufactured from zinc-coated cold-roll (coil or cut length)
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1047−10a
FIG. 1Accessories for Gypsum Wallboard and Gypsum Veneer Base
sheet steel not less than 0.012-in. (0.30-mm) thick before 4.3.5 PC, Specification D3935, PC0110
application of coating.
4.4 Paper components of accessories manufactured from
4.1.1 Sheet steel, zinc-coated by the hot-dip process, shall
steel and paper in combination shall comply with requirements
be in accordance with Specification A653/A653M, minimized
for thickness, tensile stren
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1047–10 Designation: C1047 – 10a
Standard Specification for
Accessories for Gypsum Wallboard and Gypsum Veneer
1
Base
This standard is issued under the fixed designation C1047; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers accessories used in conjunction with assemblies of gypsum wallboard and gypsum veneer base to
protect edges and corners and to provide architectural features (see Fig. 1).
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A463/A463M Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process
A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process
A879/A879M Specification for Steel Sheet, Zinc Coated by the Electrolytic Process forApplications Requiring Designation of
the Coating Mass on Each Surface
B69 Specification for Rolled Zinc
B117 Practice for Operating Salt Spray (Fog) Apparatus
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C475/C475M Specification for Joint Compound and Joint Tape for Finishing Gypsum Board
C587 Specification for Gypsum Veneer Plaster
3
D1788 Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Plastics
D3678 Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions
D3935 Specification for Polycarbonate (PC) Unfilled and Reinforced Material
D4549 Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS)
D5927 ClassificationSystemforThermoplasticPolyester(TPES)InjectionandExtrusionMaterialsBasedonISOTestMethods
D6386 Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for
Painting
3. Terminology
3.1 Definitions:
3.1.1 Definitions shall be in accordance with Terminology C11.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 accessories, n—cornerbeads, edge trims, and control joints, such as casing beads, bull noses, and stops.
3.2.2 control joint, n—a formed product used for designed or required separations between adjacent surfaces of gypsum boards
or gypsum veneer base.
3.2.3 cornerbead, n—a formed metal, plastic, or metal and paper angle for outside corners of gypsum boards or gypsum veneer
base.
3.2.4 edge trim, n—typically “J”- or “L”-shaped strip, as shown in Fig. 1, formed of metal, plastic, or metal and paper to cover
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.02 on Specifications and Test Methods for Accessories and Related Products.
Current edition approved MayOct. 1, 2010. Published JuneNovember 2010. Originally approved in 1992. Last previous edition approved in 20092010 as
C1047–09.C1047–10. DOI: 10.1520/C1047-10a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1047 – 10a
FIG. 1 Accessories for Gypsum Wallboard and Gypsum Veneer Base
exposed ends or edges of gypsum board or gypsum veneer base.
3.2.5 flange, n—that portion of the accessory used for the attachment to gypsum wallboard, gypsum veneer base, or a framing
member.
4. Materials and Manufacture
4.1 Steel accessories and steel components of accessories manufactured from steel and paper in combination shall be
manufactured from zinc-coated cold-roll (coil or cut length) sheet steel not less than 0.012-in. (0.30-mm) thick before application
of coating.
4.1.1 Sheet steel, zinc-coated by the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.