ASTM D3679-09
(Specification)Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
ABSTRACT
This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. The siding shall be made of one or more layers of poly(vinyl chloride) (PVC) compound. Any layers of materials other than poly (vinyl chloride) (PVC) compound shall be kept to less than 20% by volume. The PVC compound when extruded into siding shall maintain uniform color and be free of any visual surface or structural changes, such as peeling, chipping, cracking, flaking, or pitting. The PVC compound shall be compounded so as to provide the heat stability and weather exposure stability required for the siding market application. PVC siding shall not contain elemental lead (Pb) or compounds of that material other than traces incidental to raw materials or the manufacturing process. This limitation applies to both PVC substrate and to any cap or film material. Materials shall be tested and the individual grades shall conform to specified values of length and width, thickness, camber, heat shrinkage, impact resistance, coefficient of linear expansion, gloss, surface distortion, color, weathering, windload resistance, and nail slot allowance for thermal expansion.
SCOPE
1.1 This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. Methods of indicating compliance with this specification are also provided.
1.2 The use PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.3 Rigid (unplasticized) PVC soffit is covered in Specification D 4477.
1.4 Siding produced to this specification shall be installed in accordance with Practice D 4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.
Note 1—Information with regard to siding maintenance shall be obtained from the manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains to the test method portion only, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2—There is no known ISO equivalent to this standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: D3679 – 09
Standard Specification for
1
Rigid Poly(Vinyl Chloride) (PVC) Siding
This standard is issued under the fixed designation D3679; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
1. Scope* D374 Test Methods for Thickness of Solid Electrical Insu-
3
lation
1.1 This specification establishes requirements and test
D618 Practice for Conditioning Plastics for Testing
methodsforthematerials,dimensions,warp,shrinkage,impact
D635 Test Method for Rate of Burning and/or Extent and
strength, expansion, appearance, and windload resistance of
Time of Burning of Plastics in a Horizontal Position
extruded single-wall siding manufactured from rigid (unplas-
D696 Test Method for Coefficient of Linear Thermal Ex-
ticized) PVC compound. Methods of indicating compliance
pansion of Plastics Between Ø30°C and 30°C with a
with this specification are also provided.
Vitreous Silica Dilatometer
1.2 The use PVC recycled plastic in this product shall be in
D883 Terminology Relating to Plastics
accordance with the requirements in Section 4.
D1042 Test Method for Linear Dimensional Changes of
1.3 Rigid (unplasticized) PVC soffit is covered in Specifi-
Plastics Caused by Exposure to Heat and Moisture
cation D4477.
D1435 Practice for Outdoor Weathering of Plastics
1.4 Sidingproducedtothisspecificationshallbeinstalledin
D1600 Terminology for Abbreviated Terms Relating to
accordancewithPracticeD4756.Referenceshallalsobemade
Plastics
to the manufacturer’s installation instructions for the specific
D2244 Practice for Calculation of Color Tolerances and
product to be installed.
Color Differences from Instrumentally Measured Color
NOTE 1—Information with regard to siding maintenance shall be
Coordinates
obtained from the manufacturer.
D2457 TestMethodforSpecularGlossofPlasticFilmsand
1.5 Thevaluesstatedininch-poundunitsaretoberegarded
Solid Plastics
as standard. The values given in parentheses are mathematical
D3892 Practice for Packaging/Packing of Plastics
conversions to SI units that are provided for information only
D4226 Test Methods for Impact Resistance of Rigid Poly-
and are not considered standard.
(Vinyl Chloride) (PVC) Building Products
1.6 The following precautionary caveat pertains to the test
D4477 Specification for Rigid (Unplasticized) Poly(Vinyl
method portion only, Section 6, of this specification: This
Chloride) (PVC) Soffit
standard does not purport to address all of the safety concerns,
D4756 Practice for Installation of Rigid Poly(Vinyl Chlo-
if any, associated with its use. It is the responsibility of the user
ride) (PVC) Siding and Soffit
of this standard to establish appropriate safety and health
D5033 Guide for Development of ASTM Standards Relat-
3
practices and determine the applicability of regulatory limita-
ing to Recycling and Use of Recycled Plastics
tions prior to use.
D5206 Test Method for Windload Resistance of Rigid
Plastic Siding
NOTE 2—There is no known ISO equivalent to this standard.
E631 Terminology of Building Constructions
2. Referenced Documents
E1753 Practice for Use of Qualitative Chemical Spot Test
2
Kits for Detection of Lead in Dry Paint Films
2.1 ASTM Standards:
G147 PracticeforConditioningandHandlingofNonmetal-
lic Materials for Natural and Artificial Weathering Tests
1
This specification is under the jurisdiction of ASTM Committee D20 on
2.2 ASCE Standard:
PlasticsandisthedirectresponsibilityofSubcommitteeD20.24onPlasticBuilding
Products.
Current edition approved Feb. 1, 2009. Published February 2009. Originally
approved in 1979. Last previous edition approved in 2008 as D3679–08. DOI:
10.1520/D3679-09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Withdrawn. The last approved version of this historical standard is referenced
the ASTM website. on www.astm.org.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
D3679 – 09
ASCE7-02 Minimum Design Loads for Buildings and 4.5 The PVC compound shall be compounded so as to
4
Other Structures provide the heat stability and weather exposure stability
required f
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D3679–08 Designation: D 3679 – 09
Standard Specification for
1
Rigid Poly(Vinyl Chloride) (PVC) Siding
This standard is issued under the fixed designation D3679; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 Thisspecificationestablishesrequirementsandtestmethodsforthematerials,dimensions,warp,shrinkage,impactstrength,
expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC
compound. Methods of indicating compliance with this specification are also provided.
1.2 The use PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.3 Rigid (unplasticized) PVC soffit is covered in Specification D4477.
1.4 Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made
to the manufacturer’s installation instructions for the specific product to be installed.
NOTE 1—Information with regard to siding maintenance shall be obtained from the manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains to the test method portion only, Section 6, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
NOTE 2—There is no known ISO equivalent to this standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D374 Test Methods for Thickness of Solid Electrical Insulation
D618 Practice for Conditioning Plastics for Testing
D635 Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous Silica
Dilatometer
D883 Terminology Relating to Plastics
D1042 Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions
D1435 Practice for Outdoor Weathering of Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
D2457 Test Method for Specular Gloss of Plastic Films and Solid Plastics
D3892 Practice for Packaging/Packing of Plastics
D4226 Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products
D4477 Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
D4756 Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
D5033 Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics
D5206 Test Method for Windload Resistance of Rigid Plastic Siding
E631 Terminology of Building Constructions
E1753 Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films
G147 Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
2.2 ASCE Standard:
1
This specification is under the jurisdiction ofASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building Products.
Current edition approved Oct. 1, 2008. Published October 2008. Originally approved in 1979. Last previous edition approved in 2006 as D3679–06a.
Current edition approved . Published February 2009. Originally approved in 1979. Last previous edition approved in 2008 as D3679–08.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D3679–09
3
ASCE7-02 Minimum Design Loads for Buildings and Other
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.