ASTM F1465-03

Standard Guide for Selection of Security Control Systems (Withdrawn 2012)

SIGNIFICANCE AND USE
Warning: This guide does not identify specific technology for specific applications. It attempts to identify points of experience which will enable the planner(s) to make informed selections.
This guide should be used early in the planning stages of a project so that the proper security scope is established at the same time that the facility mission is established.
The proliferation of security technologies has become so great that evaluation and selection has become difficult.
This guide shows the planner(s) the steps required to establish the necessary and sufficient requirements for the application, and from those, how to evaluate the possible technologies for conformance to those requirements.
Using this guide, the planner(s) should be able to produce a more complete and accurate specification that meets the operational goals of the facility.
SCOPE
1.1 This guide covers the identification of issues and decisions that need to be addressed to meet the objective of specifying an operational security control system for a detention facility.
1.2 Appendix X1 contains additional sources of information that may be useful to the user of this guide.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This guide covers the identification of issues and decisions that need to be addressed to meet the objective of specifying an operational security control system for a detention facility.
Formerly under the jurisdiction of Committee F33 on Detention and Correctional Facilities, this guide was withdrawn in January 2012 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

• Status: Withdrawn
• Publication Date: 09-Sep-2003
• Withdrawal Date: 05-Jan-2012
• ICS: 13.320 - Alarm and warning systems
• Technical Committee: F33 - Detention and Correctional Facilities
• Drafting Committee: F33.06 - Control Systems

Relations

• Replaces: ASTM F1465-99 - Standard Guide for Selection of Operational Security Control Systems
• Effective Date: 10-Sep-2003

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1465–03
Standard Guide for
1
Selection of Security Control Systems
This standard is issued under the fixed designation F1465; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.4 bolt position switch (BPS), n—electrical device that
identifies the status of the deadbolt, roller bolt, or latchbolt
1.1 This guide covers the identification of issues and deci-
within a locking mechanism.
sions that need to be addressed to meet the objective of
3.1.5 building automation system, n—a system which in-
specifying an operational security control system for a deten-
cludes multiple tasks such as HVAC (heating, ventilation, air
tion facility.
conditioning) controls, in addition to specific correctional
1.2 AppendixX1containsadditionalsourcesofinformation
functions and MIS (management information systems), etc.
that may be useful to the user of this guide.
3.1.6 Class A communications, n—bidirectional signal
1.3 This standard does not purport to address all of the
within a looped wiring topology. Two cuts anywhere in the
safety concerns, if any, associated with its use. It is the
loop will disable the area between the cuts, but all other points
responsibility of the user of this standard to establish appro-
in the loop will still communicate. A single cut will not result
priate safety and health practices and determine the applica-
in a loss of communications.
bility of regulatory limitations prior to use.
3.1.7 Class B communications, n—a unidirectional signal
2. Referenced Documents within a radial wiring topology. Any interruption in the signal
2
path will disable all points beyond the interruption.
2.1 ASTM Standards:
3.1.8 client, n—a computer or application that makes use of
F1577 Test Methods for Detention Locks for Swinging
the services provided by a server. A client typically has one
Doors
user, whereas a server is shared by many different users.
2.2 International Electrotechnical Commission:
3
3.1.9 coaxial cable, n—two-conductor cable in which a
IEC 1131 Part 3—Programming Languages
center conductor is surrounded by a shield. Used for
3. Terminology
transmitting/receiving radio and video signals.
3.1.10 conformal coating, n—plastic coating to protect
3.1 Definitions:
electronic circuitry from moisture deterioration.
3.1.1 analog, adj—representing a range of values in the
3.1.11 deadlock status switch, n—an electrical component
form of a continuously variable property, such as voltage in a
within a device that provides the monitoring of a mechanical
circuit. Analog often refers to transmission methods for audio
deadlock mechanism.
and video signals.
3.1.12 detention, n—a term which includes all types of
3.1.2 audio threshold sensing, n—mechanism which moni-
facilities where people are held in custody, such as jails,
tors a preset noise level and generates an alarm when that level
prisons, and mental health facilities.
is exceeded.
3.1.13 dedicated microprocessor, n—a software–driven
3.1.3 biometrics recognition, n—means of automatically
control system created specifically to handle a defined appli-
identifying persons on the basis of unique personal character-
cation.
istics, some of which include fingerprints, voice, retina, and
3.1.14 digital, adj—representing a range of values in the
hand geometry.
form of binary (that is, on or off) digits.
3.1.15 digital signals, n—electrical information in the form
1
This guide is under the jurisdiction ofASTM Committee F33 on Detention and
of a sequence of on/off voltage.The information may be coded
Correctional Facilities and is the direct responsibility of Subcommittee F33.06 on
in many ways, so more definition is required for any particular
Control Systems.
Current edition approved Sept. 10, 2003. Published September 2003. Originally application.
approved in 1993. Last previous edition approved in 1999 as F1465 – 99. DOI:
3.1.16 direct supervision, n—management concept for op-
10.1520/F1465-03.
erating a detention facility that relies on staff’s ability to
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
manage through personal interaction between the officer and
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on inmate—doesnotrelyonphysicalbarriersortechnologyasthe
the ASTM website.
primary management mechanism.
3
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959
...