ASTM F1083-10

Standard Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Structures

ABSTRACT
This specification covers hot-dipped zinc-coated (galvanized) welded steel pipe in NPS 1, NPS 1 ¼, NPS 1 ½, NPS 2, NPS 2 ½, NPS 3, NPS3 ½, NPS 4, NPS 5, NPS 6, NPS 7, and NPS 8, with the specified nominal wall thickness, intended for fence structures such as structural support. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. The steel for welded pipe shall be be of soft weldable quality and shall be made by one or more of the following processes: electric-furnace, open hearth, or basic oxygen. Welded pipe NPS 4 and under may be butt-welded. Welded pipe over NPS 4 shall be electric welded. Pipe shall be coated with zinc inside and outside by hot-dip process. The steel pipe shall meet the tensile requirements for tensile strength and yield strength specified for regular, intermediate strength, and high strength grades. The weight of zinc coating shall be determined by strip test. The dimensional (diameter and thickness) and weight requirements for the steel pipe are specified and the test requirements for welded pipes are detailed. Lengths of toprail may be of random lengths, unless otherwise specified.
SCOPE
1.1 This specification covers hot-dipped galvanized welded steel pipe in sizes ranging from 1.315–8.625 in. (33.4 – 219.1 mm) outside diameter (OD) inclusive, with nominal (average) wall thickness as given in Table 1 and Table 2. Pipe having other dimensions (Note 2) may be furnished provided such pipe complies with all other requirements of this specification. Pipe ordered under this specification is intended for use as a structural support for fencing in accordance with Specification F1043, Group 1A.
Note 1—Outside diameter size is designated in that fence fittings are designed to securely fit on the outside of the pipe framework.
Note 2—A comprehensive listing of standardized pipe dimensions is contained in ANSI B 36.10.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
TABLE 1 Dimensions, Nominal Weights (Plain Ends) for Standard Weight Pipe (Schedule 40)
Note 1—Pipe furnished in accordance with this table will be standard pipe. Nominal size designations are names, not dimensions, thus they are a unit-less term. The dimensionless designator NPS (nominal pipe size) is referenced in this specification as it is the historical designation for schedule 40 pipe. The fence framework application requires the framework fittings to fit securely on the outside of the pipe and therefore the OD, outside diameter, is the applicable dimension for this specification.
Note 2—The wall thickness is expressed in three decimal places, the fourth decimal place being carried forward or dropped, in accordance with Practice E29.

General Information

• Status: Historical
• Publication Date: 30-Jun-2010
• ICS: 23.040.10 - Iron and steel pipes
• Technical Committee: F14 - Fences
• Drafting Committee: F14.40 - Chain Link Fence and Wire Accessories

Relations

• Replaces: ASTM F1083-08 - Standard Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Structures
• Effective Date: 01-Jul-2010
• Replaced By: ASTM F1083-13 - Standard Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Structures
• Effective Date: 15-Nov-2013
• Referred By: ASTM F2548-20 - Standard Specification for Expanded Metal Fence Systems for Security Purposes
• Effective Date: 01-Jul-2010
• Referred By: ASTM F2000-19 - Standard Safety Performance Specification for Fences for Baseball and Softball Fields
• Effective Date: 01-Jul-2010
• Referred By: ASTM F2611-15 - Standard Guide for Design and Construction of Chain Link Security Fencing
• Effective Date: 01-Jul-2010
• Referred By: ASTM E2942-22 - Standard Guide for Security of Tank Farm Installations for Compliance with Spill Prevention, Control and Countermeasure Plan (SPCC) Regulations
• Effective Date: 01-Jul-2010
• Referred By: ASTM F2409-10(2016) - Standard Guide for Fences for Non-Residential Outdoor Swimming Pools, Hot Tubs, and Spas
• Effective Date: 01-Jul-2010
• Referred By: ASTM F3000/F3000M-13(2022) - Standard Specification for Polymer Privacy Insert Slats for Chain Link Fabric and Privacy Chain Link Fabric Manufactured Containing Pre-Installed Privacy Slats
• Effective Date: 01-Jul-2010
• Referred By: ASTM F1553-11(2022) - Standard Guide for Specifying Chain Link Fence
• Effective Date: 01-Jul-2010
• Referred By: ASTM F3204-16 - Standard Guide for Design and Construction of Welded Wire Fence Systems for Security Purposes
• Effective Date: 01-Jul-2010
• Referred By: ASTM F2780-20 - Standard Guide for Design and Construction of Expanded Metal Security Fences and Barriers
• Effective Date: 01-Jul-2010
• Referred By: ASTM F3558-22 - Standard Guide for Chain-Link Pickleball Court Fences
• Effective Date: 01-Jul-2010
• Referred By: ASTM F2049-11(2017) - Standard Safety Performance Specification for Fences/Barriers for Public, Commercial, and Multi-Family Residential Use Outdoor Play Areas
• Effective Date: 01-Jul-2010
• Referred By: ASTM F900-11(2017) - Standard Specification for Industrial and Commercial Steel Swing Gates
• Effective Date: 01-Jul-2010
• Referred By: ASTM F1184-23e1 - Standard Specification for Industrial and Commercial Horizontal Slide Gates
• Effective Date: 01-Jul-2010

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1083 −10
StandardSpecification for
Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded,
1
for Fence Structures
This standard is issued under the fixed designation F1083; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2.2 ANSI Standard:
3
B 36.10 Welded and Seamless Wrought Steel Pipe
1.1 This specification covers hot-dipped galvanized welded
steel pipe in sizes ranging from 1.315–8.625 in. (33.4 – 219.1
3. Ordering Information
mm) outside diameter (OD) inclusive, with nominal (average)
3.1 Orders for material under this specification shall include
wall thickness as given in Table 1 and Table 2. Pipe having
the following as required, to describe the desired material
other dimensions (Note 2) may be furnished provided such
adequately:
pipe complies with all other requirements of this specification.
3.1.1 Specification designation,
Pipe ordered under this specification is intended for use as a
3.1.2 Quantity (feet, metres, or number of lengths),
structural support for fencing in accordance with Specification
3.1.3 Name of material (schedule 40 steel pipe or schedule
F1043, Group 1A.
80 steel pipe),
NOTE 1—Outside diameter size is designated in that fence fittings are
3.1.4 Method of manufacture (electric-resistance welded or
designed to securely fit on the outside of the pipe framework.
furnace welded),
NOTE 2—A comprehensive listing of standardized pipe dimensions is
3.1.5 Grade (Regular, Intermediate, or High Strength
contained in ANSI B 36.10.
83 000) Intermediate Strength Grade available for sizes 5.563
1.2 The values stated in inch-pound units are to be regarded
in. (141.3 mm) OD and larger. Regular and High Strength
as the standard. The values given in parentheses are for
83000 Grades are available for all sizes.
information only.
3.1.6 Type (Table 1 or Table 2),
3.1.7 Size (outside diameter and weight per foot),
2. Referenced Documents
3.1.8 Length (see Section 14),
2
2.1 ASTM Standards: 3.1.9 Certification (see 18.1), and
A90/A90M Test Method for Weight [Mass] of Coating on 3.1.10 Selection of applicable level of preservation and
Iron and Steel Articles with Zinc or Zinc-Alloy Coatings packaging required, if other than in accordance with Practices
A700 Practices for Packaging, Marking, and Loading Meth- A700 (see 20.1).
ods for Steel Products for Shipment
4. Process
B6 Specification for Zinc
E8 Test Methods for Tension Testing of Metallic Materials
4.1 The steel for welded pipe shall be made by one or more
E29 Practice for Using Significant Digits in Test Data to
of the following processes: electric-furnace, open hearth, or
Determine Conformance with Specifications
basic-oxygen. The steel for welded pipe shall be of soft
F1043 Specification for Strength and Protective Coatings on
weldable quality.
Steel Industrial Fence Framework
4.2 Weldedpipe4.500in.(114.3mm)ODandundermaybe
butt-welded, unless otherwise specified. Welded pipe over
4.500 in. (114.3 mm) OD shall be electric-welded.
1
This specification is under the jurisdiction of Committee F14 on Fences and is
the direct responsibility of Subcommittee F14.40 on Chain Link Fence and Wire
5. Coating
Accessories.
Current edition approved July 1, 2010. Published July 2010. Originally approved
5.1 Pipe shall be coated with zinc inside and outside by the
in 1987. Last previous edition approved in 2008 as F1083 – 08. DOI: 10.1520/
hot-dip process.
F1083-10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1083−10
TABLE 1 Dimensions, Nominal Weights (Plain Ends) for Standard Weight Pipe (Schedule 40)
NOTE 1—Pipe furnished in accordance with this table will be standard pipe. Nominal size designations are names, not dimensions, thus they are a
unit-less term. The dimensionless designator NPS (nominal pipe size) is referenced in this specification as it is the historical designation for schedule 40
pipe. The fence framework application requires the framework fittings to fit securely on the outside of the pipe and therefore the OD, outside diameter,
is the applicable dim
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F1083–08 Designation: F1083 – 10
Standard Specification for
Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded,
1
for Fence Structures
This standard is issued under the fixed designation F1083; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1This specification covers hot-dipped galvanized welded steel pipe in NPS 1 (Note 1) to NPS 8, inclusive, with nominal
(average) wall thickness as given in
1.1 This specification covers hot-dipped galvanized welded steel pipe in sizes ranging from 1.315–8.625 in. (33.4 – 219.1 mm)
outside diameter (OD) inclusive, with nominal (average) wall thickness as given in Table 1 and Table 2. Pipe having other
dimensions (Note 2) may be furnished provided such pipe complies with all other requirements of this specification. Pipe ordered
under this specification is intended for use as a structural support for fencing in accordance with Specification F1043, Group 1A.
NOTE1—The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for such traditional terms as nominal diameter,
size, and nominal size. 1—Outside diameter size is designated in that fence fittings are designed to securely fit on the outside of the pipe framework.
NOTE 2—A comprehensive listing of standardized pipe dimensions is contained in ANSI B 36.10.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in bracketsparentheses are for
information only.
2. Referenced Documents
2
2.1 ASTM Standards:
A53/A53MSpecification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment
B6 Specification for Zinc
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
F1043 Specification for Strength and Protective Coatings on Steel Industrial Chain Link Fence Framework
2.2 ANSI Standard:
3
B 36.10 Welded and Seamless Wrought Steel Pipe
3. Ordering Information
3.1 Orders for material under this specification shall include the following as required, to describe the desired material
adequately:
3.1.1 Specification designation,
3.1.2 Quantity (feet, metres, or number of lengths),
3.1.3Name of material (steel pipe),
3.1.3 Name of material (schedule 40 steel pipe or schedule 80 steel pipe),
3.1.4 Method of manufacture (electric-resistance welded or furnace welded),
3.1.5 Grade(Regular,Intermediate,orHighStrength83 000)IntermediateStrengthGradeavailableforsizesNPS5(125)5.563
in. (141.3 mm) OD and larger. Regular and High Strength 83000 Grades are available for all sizes.
3.1.6 Type (Table 1 or Table 2),
1
This specification is under the jurisdiction of Committee F14 on Fences and is the direct responsibility of Subcommittee F14.40 on Chain Link Fence and Wire
Accessories.
Current edition approved Feb.July 1, 2008.2010. Published February 2008.July 2010. Originally approved in 1987. Last previous edition approved in 20062008 as
F1083 – 068. DOI: 10.1520/F1083-108.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1083 – 10
TABLE 1 Dimensions, Nominal Weights (Plain Ends) for Standard Weight Pipe (Schedule 40)
NOTE 1—Pipe furnished in accordance with this table will be standard pipe. Nominal size designations are names, not dimensions, thus they are a
unit-less term. The dimensionless designator NPS (nominal pipe size) is referenced in this specification as it is the historical designation for schedule 40
pipe. The fence framework application requires the framework fittings to fit securely
...