ASTM E984-95(2001)
(Guide)Standard Guide for Identifying Chemical Effects and Matrix Effects in Auger Electron Spectroscopy
Standard Guide for Identifying Chemical Effects and Matrix Effects in Auger Electron Spectroscopy
SCOPE
1.1 This guide outlines the types of chemical effects and matrix effects which are observed in Auger electron spectroscopy.
1.2 Guidelines are given for the reporting of chemical and matrix effects in Auger spectra.
1.3 Guidelines are given for utilizing Auger chemical effects for identification or characterization.
1.4 This guide is applicable to both electron excited and X-ray excited Auger electron spectroscopy.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E984–95(Reapproved2001)
Standard Guide for
Identifying Chemical Effects and Matrix Effects in Auger
1
Electron Spectroscopy
This standard is issued under the fixed designation E 984; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope for a particular element in the specimen under study compared
to the Auger spectrum produced by the same element when it
1.1 This guide outlines the types of chemical effects and
is in some reference form. The differences in the two spectra
matrix effects which are observed in Auger electron spectros-
are said to be due to a “chemical effect” or a “matrix effect.”
copy.
Despite sometimes making elemental identification and quan-
1.2 Guidelines are given for the reporting of chemical and
titative measurements more difficult, these effects in theAuger
matrix effects in Auger spectra.
spectrum are considered valuable tools for characterizing the
1.3 GuidelinesaregivenforutilizingAugerchemicaleffects
environment of the near-surface atoms in a solid.
for identification or characterization.
1.4 This guide is applicable to both electron excited and
5. Defining Auger Chemical Effects and Matrix Effects
X-ray excited Auger electron spectroscopy.
5.1 Ingeneral,Augerchemicalandmatrixeffectsmayresult
1.5 This standard does not purport to address all of the
in(a)ashiftintheenergyofanAugerpeak,(b)achangeinthe
safety concerns, if any, associated with its use. It is the
shape of anAuger electron energy distribution, (c) a change in
responsibility of the user of this standard to establish appro-
the shape of the electron energy loss distribution associated
priate safety and health practices and determine the applica-
with an Auger peak, or (d) a change in the Auger signal
bility of regulatory limitations prior to use.
strengths of an Auger transition. The above changes may be
2. Referenced Documents due to the bonding or chemical environment of the element
(chemical effect) or to the distribution of the element or
2.1 ASTM Standards:
2
compound within the specimen (matrix effect).
E 673 Terminology Relating to Surface Analysis
5.2 The Auger chemical shift is one of the most commonly
E 827 Practice for Elemental Identification by Auger Elec-
2
observed chemical effects. A comparison can be made to the
tron Spectroscopy
more familiar chemical shifts in XPS (X-ray photoelectron
E 983 Guide for Minimizing Unwanted Electron Beam
2
spectroscopy) photoelectron lines, where energy shifts are
Effects In Auger Electron Spectroscopy
caused by changes in the ionic charge on an atom, the lattice
E 996 Practice for Reporting Data in Auger Electron Spec-
2
potential at that atomic site, and the final-state relaxation
troscopy
3
energy contributed by adjacent atoms (1 and 2). Coverage by
3. Terminology
gas adsorbates on metal surfaces may also cause shifts in the
metal Auger peak energies (3). The magnitude of the Auger
3.1 Terms used in Auger electron spectroscopy are defined
chemical shift will usually be different from the XPS photo-
in Terminology E 673.
electron shift because the Auger process involves a two-hole
4. Significance and Use
final state for the atom which is more strongly influenced by
extra-atomic relaxation. Frequently an Auger chemical shift is
4.1 Auger electron spectroscopy is often capable of yielding
larger than an XPS chemical shift (see Fig. 1).
informationconcerningthechemicalandphysicalenvironment
5.2.1 Related to chemical shifts is the (modified) Auger
of atoms in the near-surface region of a solid as well as giving
parameter, defined as the sum of the photoelectron binding
elemental and quantitative information. This information is
energy and the Auger electron kinetic energy (4). Because the
manifestedaschangesintheobservedAugerelectronspectrum
Auger parameter is the difference between two line energies of
the same element of the same specimen, it is independent of
any electrical charging of the specimen and spectrometer
1
This guide is under the jurisdiction of ASTM Committee E-42 on Surface
energy reference level, making it easier to identify chemical
Analysis and is the direct responsibility of Subcommittee E42.03 onAuger Electron
Spectroscopy and XPS.
Current edition approved Sept. 10, 1995. Published November 1995. Originally
3
published as E 984 – 84. Last previous edition E 984 – 89. The boldface numbers in parentheses refer to the references at the end of this
2
Annual Book of ASTM Standards, Vol 03.06. standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
----------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.