ASTM B949-13
(Specification)Standard Specification for General Requirements for Zinc and Zinc Alloy Products
Standard Specification for General Requirements for Zinc and Zinc Alloy Products
ABSTRACT
This specification establishes general requirements, unless otherwise specified in the specific product specification, for zinc and zinc alloy products. Final product (ingots, slabs, jumbos, etc.) shall conform to the chemical composition requirements prescribed in the applicable product specification. The determination of chemical composition shall be made in accordance with suitable spectrochemical or chemical methods. Methods of sampling for chemical analysis includes: (1) sampling during casting of ingots, slabs, blocks or jumbos, and wrought products, (2) sampling in the event of a dispute or if the alloy is at the customer�s plant, (3) sampling of zinc alloy ingots for routine testing, nominal quality, non-dispute situations, and (4) sampling of final product castings. Sampling may be done by sawing, milling, drilling, turning, or clipping. Color code requirements for the alloy are detailed.
SCOPE
1.1 This specification establishes general requirements, unless otherwise specified in the specific product specification, for ordering information, marking, and sampling for chemical analysis common to zinc and zinc alloy products and shall apply to Specifications B6, B69, B86, B240, B327, B418, B750, B792, B793, B833, B852, B860, B892, B894, B897, B907, and B943 to the extent referenced therein.
1.2 Although this specification establishes general requirements, it does not restrict that, by agreement between customer and supplier, these requirements may be altered by a customer to suit individual need.
1.3 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This applies except where SI units only are specified.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B949 −13
Standard Specification for
1
General Requirements for Zinc and Zinc Alloy Products
This standard is issued under the fixed designation B949; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* B86 Specification for Zinc and Zinc-Aluminum (ZA) Alloy
Foundry and Die Castings
1.1 This specification establishes general requirements, un-
B240 Specification for Zinc and Zinc-Aluminum (ZA) Al-
less otherwise specified in the specific product specification,
loys in Ingot Form for Foundry and Die Castings
for ordering information, marking, and sampling for chemical
B327 Specification for Master Alloys Used in Making Zinc
analysis common to zinc and zinc alloy products and shall
Die Casting Alloys
apply to Specifications B6, B69, B86, B240, B327, B418,
B418 Specification for Cast and Wrought Galvanic Zinc
B750, B792, B793, B833, B852, B860, B892, B894, B897,
Anodes
B907, and B943 to the extent referenced therein.
B750 Specification for GALFAN (Zinc-5 % Aluminum-
1.2 Although this specification establishes general
Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
requirements, it does not restrict that, by agreement between
B792 Specification for Zinc Alloys in Ingot Form for Slush
customer and supplier, these requirements may be altered by a
Casting
customer to suit individual need.
B793 Specification for Zinc Casting Alloy Ingot for Sheet
1.3 The chemical composition, physical and mechanical
Metal Forming Dies and Plastic Injection Molds
properties, and all other requirements not included in this
B833 Specification for Zinc and Zinc Alloy Wire for Ther-
specification shall be prescribed in the product specification.
malSpraying(Metallizing)fortheCorrosionProtectionof
Steel
1.4 The values stated in inch-pound units are to be regarded
B852 Specification for Continuous Galvanizing Grade
as standard. The values given in parentheses are mathematical
(CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet
conversions to SI units that are provided for information only
Steel
and are not considered standard. This applies except where SI
B860 Specification for Zinc Master Alloys for Use in Hot
units only are specified.
Dip Galvanizing
1.5 This standard does not purport to address all of the
B892 Specification forACuZinc5 (Zinc-Copper-Aluminum)
safety concerns, if any, associated with its use. It is the
Alloy in Ingot Form for Die Castings
responsibility of the user of this standard to become familiar
B894 Specification forACuZinc5 (Zinc-Copper-Aluminum)
with all hazards including those identified in the appropriate
Alloy Die Castings
Material Data Sheet (MSDS) for this product/material as
B897 Specification for Configuration of Zinc and ZincAlloy
provided by the manufacturer, to establish appropriate safety
Jumbo Block and Half Block Ingot
and health practices, and determine the applicability of regu-
B899 Terminology Relating to Non-ferrous Metals and Al-
latory limitations prior to use.
loys
B907 Specification for Zinc, Tin and Cadmium Base Alloys
2. Referenced Documents
Used as Solders
2
2.1 ASTM Standards:
B908 Practice for the Use of Color Codes for Zinc Casting
B6 Specification for Zinc
Alloy Ingot
B69 Specification for Rolled Zinc
B914 Practice for Color Codes on Zinc and ZincAlloy Ingot
for Use in Hot-Dip Galvanizing of Steel
1
This specification is under the jurisdiction of ASTM Committee B02 on
B943 Specification for Zinc and Tin Alloy Wire Used in
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
Thermal Spraying for Electronic Applications
B02.04 on Zinc and Cadmium.
B960 Specification for Prime Western Grade-Recycled
Current edition approved Aug. 1, 2013. Published September 2013. Originally
(PWG-R) Zinc
approved in 2006. Last previous edition approved in 2008 as B949 – 08. DOI:
10.1520/B0949-13.
E55 Practice for Sampling Wrought Nonferrous Metals and
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Alloys for Determination of Chemical Composition
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
E88 Practice for Sampling Nonferrous Metals and Alloys in
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Cast Form for Determination of Chemical Composition
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B949−13
E634 Practice for Sampling of Zinc and Zinc Alloys by 6. Sampling for Determination of Che
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B949 − 08 B949 − 13
Standard Specification for
1
General Requirements for Zinc and Zinc Alloy Products
This standard is issued under the fixed designation B949; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification establishes general requirements, unless otherwise specified in the specific product specification, for
ordering information, marking, and sampling for chemical analysis common to zinc and zinc alloy products and shall apply to
Specifications B6, B69, B86, B240, B327, B418, B750, B792, B793, B833, B852, B860, B892, B894, B897, B907, and B943 to
the extent referenced therein.
1.2 Although this specification establishes general requirements, it does not restrict that, by agreement between customer and
supplier, these requirements may be altered by a customer to suit individual need.
1.3 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification
shall be prescribed in the product specification.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard. This applies except where SI units
only are specified.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet
(MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B6 Specification for Zinc
B69 Specification for Rolled Zinc
B86 Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings
B240 Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings
B327 Specification for Master Alloys Used in Making Zinc Die Casting Alloys
B418 Specification for Cast and Wrought Galvanic Zinc Anodes
B750 Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
B792 Specification for Zinc Alloys in Ingot Form for Slush Casting
B793 Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds
B833 Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel
B852 Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel
B860 Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing
B892 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy in Ingot Form for Die Castings
B894 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy Die Castings
B897 Specification for Configuration of Zinc and Zinc Alloy Jumbo Block and Half Block Ingot
B899 Terminology Relating to Non-ferrous Metals and Alloys
B907 Specification for Zinc, Tin and Cadmium Base Alloys Used as Solders
B908 Practice for the Use of Color Codes for Zinc Casting Alloy Ingot
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.04 on Zinc
and Cadmium.
Current edition approved May 15, 2008Aug. 1, 2013. Published May 2008September 2013. Originally approved in 2006. Last previous edition approved in 20062008 as
B949 - 06.B949 – 08. DOI: 10.1520/B0949-08.10.1520/B0949-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B949 − 13
B914 Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel
B943 Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications
B960 Specification f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.