ASTM B967/B967M-12a
(Specification)Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
SCOPE
1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49250, C49255, C49260, C49300, C49340, C49350, C49355, and C49360 intended for use in plumbing applications and drinking water systems.
1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm inclusive] is furnished in coil form, and H50 shapes.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B967/B967M −12a
StandardSpecification for
1
Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
This standard is issued under the fixed designation B967/B967M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* E54 Test Methods for ChemicalAnalysis of Special Brasses
3
and Bronzes (Withdrawn 2002)
1.1 This specification establishes the requirements for
E62 Test Methods for Chemical Analysis of Copper and
copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS
3
CopperAlloys (Photometric Methods)(Withdrawn 2010)
Nos. C49250, C49255, C49260, C49300, C49340, C49350,
E92 Test Method forVickers Hardness of Metallic Materials
C49355,andC49360intendedforuseinplumbingapplications
3
(Withdrawn 2010)
and drinking water systems.
E478 Test Methods for ChemicalAnalysis of CopperAlloys
1.2 Typically, rod and bar product made to this specification
2.2 Other Standards:
is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8
ISO No. 3110 (AA) Copper Alloys – Determination of Alu-
mm inclusive] is furnished in coil form, and H50 shapes. 4
minum as an Alloying Element – Volumetric (Interna-
1.3 Units—The values stated in either SI units or inch- tional Organization of Standardization)
pound units are to be regarded separately as standard. The JIS H 1068:2005 Method for Determination of Bismuth in
5
values stated in each system may not be exact equivalents; Copper and Copper Alloys (Japanese Industrial Stan-
therefore,eachsystemshallbeusedindependentlyoftheother. dards)
Combining values from the two systems may result in non-
3. General Requirements
conformance with the standard.
3.1 The following sections of Specifications B249/B249M
1.4 The following safety hazard caveat pertains only to the
or B250/B250M constitute a part of this specification:
test method(s) described in this specification.
3.1.1 Terminology,
1.4.1 This standard does not purport to address all of the
3.1.2 Materials and Manufacture,
safety concerns, if any, associated with its use. It is the
3.1.3 Sampling,
responsibility of the user of this standard to establish appro-
3.1.4 Number of Tests and Retests,
priate safety and health practices and determine the applica-
3.1.5 Specimen Preparation,
bility of regulatory limitations prior to use.
3.1.6 Certification,
3.1.7 Test Reports.
2. Referenced Documents
2
2.1 ASTM Standards: 3.2 In addition, when a section with a title identical to that
referenced in X.1, above, appears in this specification, it
B249/B249M Specification for General Requirements for
Wrought Copper and Copper-Alloy Rod, Bar, Shapes and contains additional requirements which supplement those ap-
pearing in Specifications B249/B249M or B250/B250M.
Forgings
B250/B250M Specification for General Requirements for
4. Terminology
Wrought Copper Alloy Wire
B846 Terminology for Copper and Copper Alloys
4.1 For definitions of terms related to copper and copper
E8/E8M Test Methods for Tension Testing of Metallic Ma- alloys, refer to Terminology B846.
terials
5. Ordering Information
5.1 Include the following information when placing orders
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
for product under this specification, as applicable:
and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod,
5.1.1 ASTM designation and year of issue,
Bar, Wire, Shapes and Forgings.
Current edition approved Oct. 1, 2012. Published January 2013. Originally
approved in 2009. Last previous edition approved in 2012 as B967/B967M – 12.
3
DOI: 10.1520/B0967_B0967M-12A. The last approved version of this historical standard is referenced on
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or www.astm.org.
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from International Organization of Standards, http://www.ISO.org/
Standards volume information, refer to the standard’s Document Summary page on ISO/store.htm
5
the ASTM website. Japanese Industrial Standard, available through http://www.JIS.or.jp/
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B967/B967M−12a
5.1.2 Copper Alloy UNS designation, specified in the ordering information.
5.1.3 Temper (Section 8),
7.2 These composition limits do not preclude the presence
5.1.4 Dimensions, diameter, or distance between parallel
ofotherelements.Byagreementbetweenthemanufacturerand
surfaces,
purchaser, limits may be establis
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B967/B967M − 12 B967/B967M − 12a
Standard Specification for
1
Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
This standard is issued under the fixed designation B967/B967M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos.
C49250, C49255, C49260, C49300, C49340, C49350, C49355, and C49360 intended for use in plumbing applications and
drinking water systems.
1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08-0.3 in. [2-8 mm
inclusive] is furnished in coil form, and H50 shapes.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
B250/B250M Specification for General Requirements for Wrought Copper Alloy Wire
B846 Terminology for Copper and Copper Alloys
E8/E8M Test Methods for Tension Testing of Metallic Materials
3
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)
3
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)
3
E92 Test Method for Vickers Hardness of Metallic Materials (Withdrawn 2010)
E478 Test Methods for Chemical Analysis of Copper Alloys
2.2 Other Standards:
4
ISO No. 3110 (AA) Copper Alloys – Determination of Aluminum as an Alloying Element – Volumetric (International
Organization of Standardization)
5
JIS H 1068:2005 Method for Determination of Bismuth in Copper and Copper Alloys (Japanese Industrial Standards)
3. General Requirements
3.1 The following sections of Specifications B249/B249M or B250/B250M constitute a part of this specification:
3.1.1 Terminology,
3.1.2 Materials and Manufacture,
3.1.3 Sampling,
3.1.4 Number of Tests and Retests,
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod, Bar,
Wire, Shapes and Forgings.
Current edition approved April 1, 2012Oct. 1, 2012. Published May 2012January 2013. Originally approved in 2009. Last previous edition approved in 20112012 as
B967/B967M – 11a.B967/B967M – 12. DOI: 10.1520/B0967_B0967M-12.10.1520/B0967_B0967M-12A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from International Organization of Standards, http://www.ISO.org/ISO/store.htm
5
Japanese Industrial Standard, available through http://www.JIS.or.jp/
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B967/B967M − 12a
3.1.5 Specimen Preparation,
3.1.6 Certification,
3.1.7 Test Reports.
3.2 In addition, when a section with a title identical to that referenced in X.1, above, appears in this specification, it contains
additional requirements which supplement those appearing in Specifications B249/B249M or B250/B250M.
4. Terminology
4.1 For definitions of terms related to copper and copper alloys, refer to Terminology B846.
5. Ordering Information
5.1 Include the following information when placing orders for product under thi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.