ASTM D2949-10
(Specification)Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, deflection load, crush resistance, flattening resistance, impact resistance, and solvent cement. A form of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded.
Note 1—This specification was formerly issued under the title, 3-in. Thin Wall Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings.
Note 2—Techniques for making solvent-cement joints are given in Practice D2855.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2949 −10 An American National Standard
Standard Specification for
3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic
1
Drain, Waste, and Vent Pipe and Fittings
This standard is issued under the fixed designation D2949; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
tics
1.1 This specification covers requirements and test methods
D1784Specification for Rigid Poly(Vinyl Chloride) (PVC)
formaterials,dimensionsandtolerances,deflectionload,crush
Compounds and Chlorinated Poly(Vinyl Chloride)
resistance, flattening resistance, impact resistance, and solvent
(CPVC) Compounds
cement.Aformofmarkingisalsoincluded.Plasticwhichdoes
D2122Test Method for Determining Dimensions of Ther-
not meet the material requirements specified in Section 5 is
moplastic Pipe and Fittings
excluded.
D2152Test Method for Adequacy of Fusion of Extruded
NOTE 1—This specification was formerly issued under the title, 3-in.
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
ThinWallPoly(VinylChloride)(PVC)PlasticDrain,Waste,andVentPipe
Acetone Immersion
and Fittings.
D2412Test Method for Determination of External Loading
NOTE 2—Techniques for making solvent-cement joints are given in
Characteristics of Plastic Pipe by Parallel-Plate Loading
Practice D2855.
D2444Test Method for Determination of the Impact Resis-
1.2 Thetextofthisspecificationreferencesnotes,footnotes,
tance of Thermoplastic Pipe and Fittings by Means of a
and appendixes which provide explanatory material. These
Tup (Falling Weight)
notesandfootnotes(excludingthoseintablesandfigures)shall
D2564Specification for Solvent Cements for Poly(Vinyl
not be considered as requirements of the specification.
Chloride) (PVC) Plastic Piping Systems
1.3 The values stated in inch-pound units are to be regarded
D2855Practice for the Two-Step (Primer and Solvent Ce-
as standard. The values given in parentheses are mathematical
ment) Method of Joining Poly (Vinyl Chloride) (PVC) or
conversions to SI units that are provided for information only
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and
and are not considered standard.
Piping Components with Tapered Sockets
1.4 The following precautionary caveat pertains only to the
D3311Specification for Drain, Waste, and Vent (DWV)
test methods portion, Section 7, of this specification: This Plastic Fittings Patterns
standard does not purport to address all of the safety concerns,
F402 Practice for Safe Handling of Solvent Cements,
if any, associated with its use. It is the responsibility of the user Primers, and Cleaners Used for Joining Thermoplastic
of this standard to establish appropriate safety and health
Pipe and Fittings
practices and determine the applicability of regulatory limita- F412Terminology Relating to Plastic Piping Systems
tions prior to use.
F1498SpecificationforTaperPipeThreads60°forThermo-
plastic Pipe and Fittings
2. Referenced Documents
3. Terminology
2
2.1 ASTM Standards:
3.1 Definitions—Definitions are in accordance with Termi-
D618Practice for Conditioning Plastics for Testing
nology F412, and abbreviations are in accordance with Termi-
nology D1600, unless otherwise specified.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
4. Significance and Use
Current edition approved Nov. 15, 2010. Published January 2011. Originally
ε1
4.1 The requirements of this specification are intended to
approvedin1971.Lastpreviouseditionapprovedin2008asD2949–01a(2008) .
DOI: 10.1520/D2949-10.
provide pipe and fittings suitable for drainage of sewage and
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
certain other liquid wastes where toughness, resistance to
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
deterioration from water and chemicals, flattening and aging
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. resistance, and strong tight joints are required.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2949−10
4.2 When joining 3.25-in. outside diameter PVC DWV 6.2.2.4 Fittings Dimensions—The dimensions of fittings
piping to 3-in. Schedule 40 PVC DWV piping, it is necessary coveredbythisspecificationshallmeettherequirementsgiven
to use either reducer bushings or increasers, as
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
´1
Designation:D2949–01a (Reapproved 2008) Designation: D2949 – 10
Standard Specification for
3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic
1
Drain, Waste, and Vent Pipe and Fittings
This standard is issued under the fixed designation D2949; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—6.6 was editorially corrected in March 2010.
1. Scope*
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, deflection load, crush
resistance, hydrostatic-burst resistance, flattening resistance, impact resistance, and solvent cement. A form of marking is also
included. Plastic which does not meet the material requirements specified in Section 5 is excluded.
NOTE 1—This specification was formerly issued under the title, 3-in. Thin Wall Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and
Fittings.
NOTE 2—Techniques for making solvent-cement joints are given in Practice D2855.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing D1599Test Method for Resistance to Short-Time Hydraulic Pressure of
Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone
Immersion
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 TestMethodforDeterminationoftheImpactResistanceofThermoplasticPipeandFittingsbyMeansofaTup(Falling
Weight)
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2855 Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Nov. 1, 2008.15, 2010. Published February 2009.January 2011. Originally approved in 1971. Last previous edition approved in 20012008 as
´1
D2949–01a(2008) . DOI: 10.1520/D2949-01AR08. DOI: 10.1520/D2949-10.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D2949 – 10
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology
D1600, unless otherwise specified.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.