iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D1758-06

(Test Method)

Standard Test Method of Evaluating Wood Preservatives by Field Tests with Stakes (Withdrawn 2015)

Standard Test Method of Evaluating Wood Preservatives by Field Tests with Stakes (Withdrawn 2015)

ABSTRACT
This test method covers accelerated procedures for determining the relative permanence and effectiveness of wood preservatives in stakes exposed in field plots. The sapwood of southern pine shall be the preferred wood for comparative tests. The pretreatment selections and treatment procedure of test stakes are presented in details. The after treatment handling of test stakes, and installation of stakes are presented in details. The periodic calculation of the index of condition, short-cut method, percent of index condition, and termination of test shall be evaluated to meet the requirements prescribed.
SCOPE
1.1 This test method covers accelerated procedures for determining the relative permanence and effectiveness of wood preservatives in stakes exposed in field plots.
1.2 The requirements for preparation of the material for testing and the test procedures appear in the following order:
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This test method covered accelerated procedures for determining the relative permanence and effectiveness of wood preservatives in stakes exposed in field plots.
Formerly under the jurisdiction of Committee D07 on Wood, this test method was withdrawn in January 2015 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Withdrawn
Publication Date
31-May-2006
Withdrawal Date
12-Jan-2015
ICS
71.100.50 - Wood-protecting chemicals
Technical Committee
D07 - Wood
Drafting Committee
D07.06 - Treatments for Wood Products
Current Stage
Ref Project

Relations

Replaces
ASTM D1758-05 - Standard Test Method of Evaluating Wood Preservatives by Field Tests with Stakes
Effective Date
01-Jun-2006

Buy Standard

ASTM D1758-06 - Standard Test Method of Evaluating Wood Preservatives by Field Tests with Stakes (Withdrawn 2015)ASTM D1758-06 - Standard Test Method of Evaluating Wood Preservatives by Field Tests with Stakes (Withdrawn 2015)
PreviousNext
Standard
ASTM D1758-06 - Standard Test Method of Evaluating Wood Preservatives by Field Tests with Stakes (Withdrawn 2015)
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D1758 − 06
StandardTest Method of
1
Evaluating Wood Preservatives by Field Tests with Stakes
This standard is issued under the fixed designation D1758; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1413Test Method for Wood Preservatives by Laboratory
Soil-Block Cultures
1.1 This test method covers accelerated procedures for
D1625Specification for Chromated CopperArsenate (With-
determiningtherelativepermanenceandeffectivenessofwood
3
drawn 2006)
preservatives in stakes exposed in field plots.
1.2 The requirements for preparation of the material for
3. Summary of Test Method
testing and the test procedures appear in the following order:
3.1 Wood stakes are impregnated with an appropriate series
Sections
of retentions of a preservative, and then handled, prior to
Summary of Test Method 3
Test Plot 4
exposure in the field, according to specified procedures. The
Test Specimens 5
treated stakes are exposed in the ground to the action of
Pretreatment Selection of Test Stakes 6
wood-destroying fungi and termites in one or more selected
Treatment Procedure 7
After Treatment Handling of Test Stakes 8
field plots. An index of condition determined from grades
Installation of Stakes 9
assignedtothestakesfordegreeofdecayandtermiteattack,in
Inspection of Specimens 10
the course of periodic inspections, is used to express results
Evaluation of Results 11
Reports 12
periodically and at the termination of the test.
1.3 The values stated in SI units are to be regarded as the
3.2 Two test procedures are outlined, employing two speci-
standard. The values given in parentheses are for information
3
men types, ⁄4-in. square and nominal 2 by 4-in. stakes,
only.
designated hereafter respectively as Method A and Method B.
1.4 This standard does not purport to address all of the Method A, using smaller and more numerous specimens, is
safety concerns, if any, associated with its use. It is the preferred for possibly more rapid results, and Method B for
responsibility of the user of this standard to establish appro- longer-term tests of a quasi service nature.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
4. Test Plot
4.1 General Requirements—A warm humid climate is pre-
2. Referenced Documents
ferred. Select a natural area of fertile, fallow, level land of
2
2.1 ASTM Standards:
uniform soil character that is moist but well drained and large
D246TestMethodforDistillationofCreosoteandCreosote-
enough to permit expansion of future stake installations. The
3
Coal Tar Solutions (Withdrawn 2006)
presence of wood-destroying fungi and active subterranean
D390Specification for Coal-Tar Creosote for the Preserva-
termites shall be proved by observation or experience and
tive Treatment of Piles, Poles, and Timbers for Marine,
checked by exposure of suitable small specimens of untreated
3
Land, and Freshwater Use (Withdrawn 2006)
wood. No natural or artificial fertilizer or other chemicals shall
beappliedtotheplotduringitsuseasatestground.Protection
against fire, predators, and pilferage shall be provided as far as
practicable.
1
This test method is under the jurisdiction of ASTM Committee D07 on Wood
and is the direct responsibility of Subcommittee D07.06 on Treatments for Wood
4.2 Control of Vegetation—As a general rule, vegetation
Products.
shall be controlled manually or by suitable mechanical means
Current edition approved June 1, 2006. Published June 2006. Originally
approved in 1962. Last previous edition approved in 2005 as D1758–05. DOI:
onlyandwithminimumsoildisturbance.Nochemicalcontrols
10.1520/D1758-06.
shall be permitted. Weeding and cleaning the plot shall be
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
uniform over any given test area.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4.3 Reuse of Ground—Stakesplacedingroundthathasbeen
the ASTM website.
3
used previously for test purposes shall not be set closer than
The last approved version of this historical standard is referenced on
www.astm.org. 150 mm (6 in.) to any earlier stake location.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D1758 − 06
5. Test Specimens pressure period determined by trial lots, but omit the final
vacuum. (See 7.9 for method of obtaining gradient retentions
5.1 Selection of Wood—Sapwood of southern pine (Pi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5582-22(Test Method)
Standard Test Method for Determining Formaldehyde Levels from Wood Products Using a Desiccator

SIGNIFICANCE AND USE
3.1 Limitations have been established on formaldehyde emission levels for wood panel building products made with urea-formaldehyde adhesives and permanently installed in homes or used as components in kitchen cabinets and for similar industrial products. This test method is used in conjunction with the test method referenced by HUD Rules and Regulations 24 CFR 3280 for manufactured housing, California Air Resources Board (CARB) regulation 93120, EPA TSCA Title VI 40 CFR Section 770, and by Minnesota Statutes Section 144.495 for housing units and building materials. This test method provides a means of testing small-size samples to determine formaldehyde emission potential.  
3.2 This test method incorporates a desiccator, with the desiccant removed, having a 250 mm (10 in.) inside diameter and a volume of approximately 10.5 L (641 in.3) with the desiccator lid in place. Conditions controlled in the procedure are as follows:  
3.2.1 Conditioning of panel products prior to testing,  
3.2.2 Specified number, size, and edge sealing of wood specimens to be placed in the desiccator,  
3.2.3 Test desiccator temperature, and  
3.2.4 Samples from the 25 mL distilled water collection medium in the petri dish bottom are analyzed for formaldehyde at the end of a 2-h period in the closed desiccator.  
3.3 This test method employs a single set of environmental conditions to assess formaldehyde emission potential from certain wood products. When the relationship between desiccator test values and large-chamber test values are to be determined, the values for the specific wood panel product type shall be plotted. This test method does allow a comparison of formaldehyde levels from different products for the same use.  
3.3.1 Care must be exercised in the extension of the results to actual formaldehyde emission from products under actual use conditions.
SCOPE
1.1 This test method covers a small scale procedure for measuring formaldehyde emission potential from wood products under defined test conditions. The formaldehyde level is determined by collecting air-borne formaldehyde in a small distilled water reservoir within a closed desiccator. The quantity of formaldehyde is determined by a modification of the National Institute for Occupational Safety and Health (NIOSH) 3500 chromotropic acid test procedure. Other analytical procedures may be used to determine formaldehyde emission potential provided that such methods give similar results to the chromotropic acid procedure. However, the test results and test report must be properly qualified and the analytical procedure employed must be noted. Procedures based on acetylacetone and pararosaniline have been found to give similar results to chromotropic acid in other test methods used in determining formaldehyde emission potential from wood products (see Test Method E1333).  
1.2 Wood products typically evaluated by this test method are made with urea-formaldehyde adhesives and include particle-board, hardwood plywood, and medium-density fiberboard. This test method is used for product quality control and is a small bench test method that correlates with the large-scale acceptance test for determining formaldehyde levels from wood products, Test Method E1333. Alternative conditioning intervals may give better correlation, such as seven day conditioning that parallels Test Method E1333. The general desiccator testing procedure may be modified for different conditioning times to accommodate its use in manufacturing quality control. However, the test results must be properly qualified and the conditioning time employed must be noted.  
Note 1: If modifications are made to the conditioning period for quality control purposes, it is important that the modification is consistently applied. Otherwise, the results may not be comparable.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provide...

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D3345-22(Test Method)
Standard Test Method for Laboratory Evaluation of Wood for Resistance to Subterranean Termites

ABSTRACT
This test method covers the laboratory evaluation of treated or untreated cellulosic material for its resistance to subterranean termites. This test should be considered as a screening test for treated material and further evaluation by field methods is required. Different kinds of equipment and materials to be used in the evaluation of the cellulosic material include containers, glass or clean plastic, tray, enamel, stainless steel, paper towels, and volatile chemicals. Southern yellow pine (SYP) sapwood with no visible defects and smoothed surfaces shall be evaluated by using reagents like benzalkonium chloride solution and distilled water. Other wood species may be used, but in each separate test using other species as the major test wood, five SYP sapwood blocks should be used as additional controls to permit the correlation of test results among laboratories. A block evaluation with corresponding rating system shall be performed by visualization method.
SCOPE
1.1 This test method covers the laboratory evaluation of treated or untreated wood for its resistance to subterranean termites. This test is considered as a screening test for treated material and further evaluation by field methods is required.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—See 7.1.4.)  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D8223-19(Practice)
Standard Practice for Evaluation of Fire-Retardant Treated Laminated Veneer Lumber

SIGNIFICANCE AND USE
5.1 Design values obtained from 4.2 are permitted for use in design where the end-use temperature does not exceed 38 °C (100 °F).  
5.1.1 The mean test values for the properties evaluated in 4.2 (ftr,0) and 4.3 (ftr,108) shall be used to determine design value adjustment factors for FRT LVL that will be exposed to end-use temperatures in excess of 38 °C (100 °F) but not exceeding 66 °C (150 °F). Temperature adjustment factors in accordance with the National Design Specification for Wood Construction (NDS) shall also be applied in these applications.
SCOPE
1.1 This practice covers procedures for the evaluation of laminated veneer lumber (LVL) pressure-treated with commercially available fire retardants after exposure to both standard environmental conditions and an extended exposure to elevated temperature.  
1.2 LVL products utilizing overlays or fire-retardant paints and coatings require other considerations and are outside of the scope of this practice.  
1.3 LVL products manufactured for rim board applications require other considerations and are outside of the scope of this practice.  
1.4 This practice provides one method to establish design values for fire-retardant treated (FRT) LVL. It is not intended to preclude the use of alternative methods for deriving design values, such as Test Method D5664 and Practice D6841 for FRT lumber.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D2898-10(2017)(Practice)
Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

SIGNIFICANCE AND USE
4.1 This practice describes different methods of exposing fire-retardant-treated wood products or assemblies to controlled accelerated weathering or conditioning.  
4.2 The conditioning simulates effects of leaching, drying, temperature, and, in two methods, UV light.  
4.3 Method A is the method normally specified for regulatory purposes when testing fire-retardant-treated wood that is intended for exterior applications.
SCOPE
1.1 This practice addresses the durability of a fire-retardant treatment of wood products by exposure to accelerated cycles of wetting, drying, or ultraviolet (UV) exposure, or combination thereof, prior to evaluation by a fire response test. Four conditioning methods are described.  
1.2 This practice is applicable to wood products that have been treated with fire-retardant chemicals by pressure impregnation.  
1.3 The test specimens are to be in the form of, or suitable for fabrication into, test specimens, such as those described in Test Methods E84, E108, and E1354 and other standard test methods for evaluating the fire performance of fire-retardant-treated wood products.  
1.4 The text of these methods references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of these test methods.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3345-17(Test Method)
Standard Test Method for Laboratory Evaluation of Solid Wood for Resistance to Termites

ABSTRACT
This test method covers the laboratory evaluation of treated or untreated cellulosic material for its resistance to subterranean termites. This test should be considered as a screening test for treated material and further evaluation by field methods is required. Different kinds of equipment and materials to be used in the evaluation of the cellulosic material include containers, glass or clean plastic, tray, enamel, stainless steel, paper towels, and volatile chemicals. Southern yellow pine (SYP) sapwood with no visible defects and smoothed surfaces shall be evaluated by using reagents like benzalkonium chloride solution and distilled water. Other wood species may be used, but in each separate test using other species as the major test wood, five SYP sapwood blocks should be used as additional controls to permit the correlation of test results among laboratories. A block evaluation with corresponding rating system shall be performed by visualization method.
SCOPE
1.1 This test method covers the laboratory evaluation of treated or untreated solid wood for its resistance to subterranean termites. This test is considered as a screening test for treated material and further evaluation by field methods is required.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—See 7.1.4.)

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5582-14(Test Method)
Standard Test Method for Determining Formaldehyde Levels from Wood Products Using a Desiccator

SIGNIFICANCE AND USE
3.1 Limitations have been established on formaldehyde emission levels for wood panel building products made with urea-formaldehyde adhesives and permanently installed in homes or used as components in kitchen cabinets and for similar industrial products. This test method is used in conjunction with the test method referenced by HUD Rules and Regulations 24 CFR 3280 for manufactured housing, California Air Resources Board (CARB) regulation 93120, and by Minnesota Statutes Section 144.495 for housing units and building materials. This test method provides a means of testing small-size samples to determine formaldehyde emission potential.  
3.2 This test method incorporates a desiccator, with the desiccant removed, having a 250-mm (10-in.) inside diameter and a volume of approximately 10.5 L (641 in.3) with the desiccator lid in place. Conditions controlled in the procedure are as follows:  
3.2.1 Conditioning of panel products prior to testing,  
3.2.2 Specified number, size, and edge sealing of wood specimens to be placed in the desiccator,  
3.2.3 Test desiccator temperature, and  
3.2.4 Samples from the 25-mL distilled water collection medium in the petri dish bottom are analyzed for formaldehyde at the end of a 2-h period in the closed desiccator.  
3.3 This test method employs a single set of environmental conditions to assess formaldehyde emission potential from certain wood products. When the relationship between desiccator test values and large-chamber test values are to be determined, the values for the specific wood panel product type shall be plotted. This test method does allow a comparison of formaldehyde levels from different products for the same use.
Note 2: Care must be exercised in the extension of the results to actual formaldehyde emission from products under actual use conditions.
SCOPE
1.1 This test method covers a small scale procedure for measuring formaldehyde emission potential from wood products under defined test conditions. The formaldehyde level is determined by collecting air-borne formaldehyde in a small distilled water reservoir within a closed desiccator. The quantity of formaldehyde is determined by a modification of the National Institute for Occupational Safety and Health (NIOSH) 3500 chromotropic acid test procedure. Other analytical procedures may be used to determine formaldehyde emission potential provided that such methods give similar results to the chromotropic acid procedure. However, the test results and test report must be properly qualified and the analytical procedure employed must be noted. Procedures based on acetylacetone and pararosaniline have been found to give similar results to chromotropic acid in other test methods used in determining formaldehyde emission potential from wood products (see Test Method E1333).  
1.2 Wood products typically evaluated by this test method are made with urea-formaldehyde adhesives and include particleboard, hardwood, plywood, and medium-density fiberboard. This test method is used for product quality control and is a small bench test method that correlates with the large-scale acceptance test for determining formaldehyde levels from wood products, Test Method E1333. The general desiccator testing procedure may be modified for different conditioning times to accommodate its use in manufacturing quality control. However, the test results must be properly qualified and the conditioning time employed must be noted.  
Note 1: If modifications are made to the conditioning period for quality control purposes, it is important that the modification is consistently applied. Otherwise, the results may not be comparable.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standar...

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2898-10(Practice)
Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

SIGNIFICANCE AND USE
This practice describes different methods of exposing fire-retardant-treated wood products or assemblies to controlled accelerated weathering or conditioning.
The conditioning simulates effects of leaching, drying, temperature, and, in two methods, UV light.
Method A is the method normally specified for regulatory purposes when testing fire-retardant-treated wood that is intended for exterior applications.
SCOPE
1.1 This practice addresses the durability of a fire-retardant treatment of wood products by exposure to accelerated cycles of wetting, drying, or ultraviolet (UV) exposure, or combination thereof, prior to evaluation by a fire response test. Four conditioning methods are described.
1.2 This practice is applicable to wood products that have been treated with fire-retardant chemicals by pressure impregnation.
1.3 The test specimens are to be in the form of, or suitable for fabrication into, test specimens, such as those described in Test Methods E84, E108, and E1354 and other standard test methods for evaluating the fire performance of fire-retardant-treated wood products.
1.4 The text of these methods references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of these test methods.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2898-09(Practice)
Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

SIGNIFICANCE AND USE
This practice describes different methods of exposing fire-retardant-treated wood products or assemblies to controlled accelerated weathering or conditioning.
The conditioning simulates effects of leaching, drying, temperature, and, in two methods, UV light.
Method A is the method normally specified for regulatory purposes when testing fire-retardant-treated wood that is intended for exterior applications.
SCOPE
1.1 This practice addresses the durability of a fire-retardant treatment of wood products by exposure to accelerated cycles of wetting, drying, or ultraviolet (UV) exposure, or combination thereof, prior to evaluation by a fire response test. Four conditioning methods are described.
1.2 This practice is applicable to wood products that have been treated with fire-retardant chemicals by pressure impregnation.
1.3 The test specimens are to be in the form of, or suitable for fabrication into, test specimens, such as those described in Test Methods E84, E108, and E1354 and other standard test methods for evaluating the fire performance of fire-retardant-treated wood products.
1.4 The text of these methods references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of these test methods.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2898-08(Practice)
Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

SIGNIFICANCE AND USE
This practice describes different methods of exposing fire-retardant-treated wood products or assemblies to controlled accelerated weathering or conditioning.
The conditioning simulates effects of leaching, drying, temperature, and, in two methods, ultraviolet (UV) light.
Method A is the method normally specified for regulatory purposes when testing fire-retardant-treated wood that is intended for exterior applications.
SCOPE
1.1 This practice covers the durability of a fire-retardant treatment of wood under exposure to accelerated weathering. Four conditioning methods are described. Methods are suitable for application to a test specimen prior to subjecting that specimen to an appropriate fire test.
1.2 This practice is applicable to wood products that have been treated with fire-retardant chemicals by pressure impregnation.
1.3 The test specimens are to be in the form of, or suitable for fabrication into, test specimens, such as those described in Test Methods E 84, E 108, and E 1354 and other standard test methods for evaluating the fire performance of fire-retardant-treated wood products.
1.4 The text of these methods references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of these test methods.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2898-08e1(Practice)
Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

SIGNIFICANCE AND USE
This practice describes different methods of exposing fire-retardant-treated wood products or assemblies to controlled accelerated weathering or conditioning.
The conditioning simulates effects of leaching, drying, temperature, and, in two methods, ultraviolet (UV) light.
Method A is the method normally specified for regulatory purposes when testing fire-retardant-treated wood that is intended for exterior applications.
SCOPE
1.1 This practice covers the durability of a fire-retardant treatment of wood under exposure to accelerated weathering. Four conditioning methods are described. Methods are suitable for application to a test specimen prior to subjecting that specimen to an appropriate fire test.
1.2 This practice is applicable to wood products that have been treated with fire-retardant chemicals by pressure impregnation.
1.3 The test specimens are to be in the form of, or suitable for fabrication into, test specimens, such as those described in Test Methods E 84, E 108, and E 1354 and other standard test methods for evaluating the fire performance of fire-retardant-treated wood products.
1.4 The text of these methods references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of these test methods.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off