ASTM D6369-99(2006)
(Guide)Standard Guide for Design of Standard Flashing Details for EPDM Roof Membranes (Withdrawn 2015)
Standard Guide for Design of Standard Flashing Details for EPDM Roof Membranes (Withdrawn 2015)
SIGNIFICANCE AND USE
This guide illustrates general details for typical conditions that may be encountered on an EPDM sheet roofing system.
This guide does not address all requirements associated with the installation of EPDM membrane flashing, such as membrane cleaning and surface preparation, fastener spacing, adhesive application and other seaming requirements which may vary by membrane system supplier.
Insulation, fastener types, protection mats, stone ballast, pavers, and requirements for perimeter attachment are not covered by this guide. The designer shall review the project requirements and consult the membrane system supplier, building insurer, and local building codes for specific requirements.
SCOPE
1.1 This guide covers the design of details for typical conditions encountered in new ballasted, mechanically attached or fully adhered ethylene propylene diene terpolymer (EPDM) sheet roof systems.
1.2 This guide illustrates general details for typical conditions that may be encountered on an EPDM sheet roofing system. The guide will assist the designer in preparing details for each specific condition that may occur on a project.
1.3 The values stated in SI units are to be regarded as standard. The conventional units given in parentheses are provided for information purposes only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This guide covered the design of details for typical conditions encountered in new ballasted, mechanically attached or fully adhered ethylene propylene diene terpolymer (EPDM) sheet roof systems.
Formerly under the jurisdiction of Committee D08 on Roofing and Waterproofing, this guide was withdrawn in July 2015 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6369 − 99(Reapproved 2006)
Standard Guide for
Design of Standard Flashing Details for EPDM Roof
1
Membranes
This standard is issued under the fixed designation D6369; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.4 mechanically attached sheet roofing, n—a system which
incorporates a mechanically fastened vulcanized EPDM sheet
1.1 This guide covers the design of details for typical
over a secured and accepted substrate.
conditions encountered in new ballasted, mechanically at-
tached or fully adhered ethylene propylene diene terpolymer
4. Significance and Use
(EPDM) sheet roof systems.
4.1 This guide illustrates general details for typical condi-
1.2 This guide illustrates general details for typical condi-
tions that may be encountered on an EPDM sheet roofing
tions that may be encountered on an EPDM sheet roofing
system.
system. The guide will assist the designer in preparing details
4.2 This guide does not address all requirements associated
for each specific condition that may occur on a project.
with the installation of EPDM membrane flashing, such as
1.3 The values stated in SI units are to be regarded as
membrane cleaning and surface preparation, fastener spacing,
standard. The conventional units given in parentheses are
adhesive application and other seaming requirements which
provided for information purposes only.
may vary by membrane system supplier.
1.4 This standard does not purport to address all of the
4.3 Insulation, fastener types, protection mats, stone ballast,
safety concerns, if any, associated with its use. It is the
pavers, and requirements for perimeter attachment are not
responsibility of the user of this standard to establish appro-
covered by this guide. The designer shall review the project
priate safety and health practices and determine the applica-
requirementsandconsultthemembranesystemsupplier,build-
bility of regulatory limitations prior to use.
ing insurer, and local building codes for specific requirements.
2. Referenced Documents
5. Drawings
2
2.1 ASTM Standards:
5.1 This guide is not all-inclusive. The designer shall detail
D1079Terminology Relating to Roofing and Waterproofing
all typical and special conditions on the project. Particular
3. Terminology
attention shall be given to transitions in plane and intersection
of different details. The membrane system supplier or system
3.1 Definitions— For definitions of terms used in this guide
applicator shall provide shop drawings of each condition to
and not listed below, see Terminology D1079.
confirmfieldconditionsandtoverifytheirunderstandingofthe
3.2 ballasted sheet roofing, n—a system which incorporates
design intent.
alooselaidvulcanizedEPDMsheetoveranacceptedsubstrate
5.2 Insulation, protection mats, stone ballast and pavers
and is held in place with either stone ballast, pavers, or a
have been omitted for clarity.
combination thereof.
3.3 fully adhered sheet roofing, n—a system which incorpo- 5.3 Treated wood blocking shall be installed to provide
rates a vulcanized EPDM sheet fully adhered over a secured attachment for accessory items such as gravel stops, metal
and accepted substrate. sleeves, etc.
6. Penetrations
1
This guide is under the jurisdiction ofASTM Committee D08 on Roofing and
Waterproofing and is the direct responsibility of Subcommittee D08.18 on Nonbi-
6.1 Flashing at penetrations shall accommodate differential
tuminous Organic Roof Coverings.
movement between the deck and penetration (that is, pipe,
Current edition approved Dec. 1, 2006. Published December 2006. Originally
conduit, column or drain).
approved in 1999. Last previous edition approved in 1999 as D6369–99. DOI:
10.1520/D6369-99R06.
6.1.1 Where “H” or “I” column sections occur, install
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
blocking between flanges to facilitate installation of flashing.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Weld sloping steel hoods to column. Extend vertical leg of
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. hood a minimum 100 mm (4 in.) over flashing.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6369 − 99 (2006)
6.1.2 Set cast iron drains with the top of the flange level shall lap the joint between the wood blocking and parapet
with or slightly below the surrounding deck area. When surface a minimum 25 mm (1 in.).
insulation is installed below the sheet mem
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.