ASTM F467-03a
(Specification)Standard Specification for Nonferrous Nuts for General Use
Standard Specification for Nonferrous Nuts for General Use
SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468.
Note 1—A complete metric companion to Specification F 467 has been developed-F 467M; therefore no metric equivalents are presented in this specification.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 467 – 03a
Standard Specification for
1
Nonferrous Nuts for General Use
This standard is issued under the fixed designation F 467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
7
1. Scope loyed Copper by Gravimetry
E 54 Test Methods for Chemical Analysis of Special
1.1 This specification covers the requirements for commer-
9
Brasses and Bronzes
cial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in
E 55 PracticeforSamplingWroughtNonferrousMetalsand
diameterinanumberofalloysincommonuseandintendedfor
7
Alloys for Determination of Chemical Composition
general service applications.
E 62 Test Methods for Chemical Analysis of Copper and
1.2 Applicable bolts, cap screws, and studs for use with nuts
7
Copper Alloys (Photometric Methods)
covered by this specification are covered by Specification
E 75 Test Methods for ChemicalAnalysis of Copper-Nickel
F 468.
7
and Copper-Nickel-Zinc Alloys
NOTE 1—AcompletemetriccompaniontoSpecificationF 467hasbeen
E 76 Test Methods for ChemicalAnalysis of Nickel-Copper
developed—F 467M; therefore no metric equivalents are presented in this
7
Alloys
specification.
E 92 Test Method for Vickers Hardness of Metallic Mate-
5
rials
2. Referenced Documents
E 101 Test Method for Spectrographic Analysis of Alumi-
2.1 ASTM Standards:
num and Aluminum Alloys by the Point-to-Plane Tech-
B 154 Test Method for Mercurous Nitrate Test for Copper
10
2 nique
and Copper Alloys
E 120 Test Methods for ChemicalAnalysis of Titanium and
B 446 Specification for Nickel-Chromium-Molybdenum-
7
Titanium Alloys
Columbium-Alloy (UNS N06625), Nickel-Chromium-
11
E 165 Practice for Liquid Penetrant Examination
Molybdenum-Silicon Alloy (UNS N06219), and Nickel-
E 227 Test Method for Optical Emission Spectrometric
Chromium-Molybdenum-Tungsten Alloy (UNS N06650)
3 Analysis of Aluminum and Aluminum Alloys by the
Rod and Bar
9
4 Point-to-Plane Technique
D 3951 Practice for Commercial Packaging
E 354 Test Methods for Chemical Analysis of High-
E 18 Test Methods for Rockwell Hardness and Rockwell
5 Temperature, Electrical, Magnetic, and Other Similar Iron,
Superficial Hardness of Metallic Materials
7
Nickel, and Cobalt Alloys
E 29 Practice for Using Significant Digits in Test Data to
6 E 478 Test Methods for Chemical Analysis of Copper
Determine Conformance with Specifications
7
Alloys
E 34 Test Methods for ChemicalAnalysis ofAluminum and
7 E 1409 Test Method for Determination of Oxygen in Tita-
Aluminum Base Alloys
nium and Titanium Alloys by the Inert Gas Fusion Tech-
E 38 Methods for Chemical Analysis of Nickel-Chromium
7
8 nique
and Nickel-Chromium-Iron Alloys
F 468 Specification for Nonferrous Bolts, Hex Cap Screws,
E 53 Test Methods for Determination of Copper in Unal-
12
and Studs for General Use
F 606 Test Methods for Determining the Mechanical Prop-
1
erties of Externally and Internally Threaded Fasteners,
This specification is under the jurisdiction of ASTM Committee F16 on
12
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Washers, and Rivets
Fasteners.
F 1470 GuideforFastenerSamplingforSpecifiedMechani-
Current edition approved Oct. 1, 2003. Published October 2003. Originally
12
cal Properties and Performance Inspection
approved in 1976. Last previous edition approved in 2003 as F 467 – 03.
2
2.2 ASME Standards:
Annual Book of ASTM Standards, Vol 02.01.
3
Annual Book of ASTM Standards, Vol 02.04.
4
Annual Book of ASTM Standards, Vol 15.09.
5
Annual Book of ASTM Standards, Vol 03.01.
6 9
Annual Book of ASTM Standards, Vol 14.02. Discontinued-see 2001 Annual Book of ASTM Standards, Vol 03.05.
7 10
Annual Book of ASTM Standards, Vol 03.05. Discontinued-see 1995 Annual Book of ASTM Standards, Vol 03.05.
8 11
Discontinued-see 1988 Annual Book of ASTM Standards, Vol 03.05. Replaced Annual Book of ASTM Standards, Vol 03.03.
12
by E 350. Annual Book of ASTM Standards, Vol 01.08.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 467 – 03a
B 1.1 Unified Inch Screw Threads (UN and UNR Thread 3.1.5 Stress relieving, if required (4.2.3);
13
Form)
3.1.6 “Shipment lot” testing, as required (Section 9);
13
B 18.2.2 Square and Hex Nuts
3.1.7 Source inspection, if required (Section 14);
3.1.8 Certificate of compliance or test report, if required
3. Ordering Information
(Section 16);
3.1 Orders for nuts under this specification shall include the
3.1.9 Additional requirements,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.