iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2628-91(2016)

(Specification)

Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements

Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements

ABSTRACT
This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for concrete pavements. The seal consists of a multiple web design and is installed with a lubricant. The seal functions by compression of the seal between the faces of the joint with the seal folding inward at the top to facilitate compression. The seals shall be preformed, and the material shall be vulcanized elastomeric compound using polychloroprene as the only base polymer. The materials shall also comply with the physical properties prescribed herein such as tensile strength, elongation, hardness, oil swell, ozone resistance, low-temperature stiffening, low-temperature recovery, and compression deflection.
SCOPE
1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for concrete pavements. The seal consists of a multiple web design and functions only by compression of the seal between the faces of the joint with the seal folding inward at the top to facilitate compression. The seal is installed with a lubricant and is designed to seal the joint and reject incompressibles.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3   This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
Note 1: This specification is a manufacturing and purchasing specification only and does not include requirements or considerations for selection of size, or the installation of the joint seals. However, experience has shown that successful performance of this product depends upon the proper selection of size and cross-sectional design of the joint seal, joint size, and joint spacing for the ambient conditions the pavement will be exposed to, and care in the installation of the joint seals.

General Information

Status
Published
Publication Date
30-Sep-2016
ICS
93.080.10 - Road construction
Technical Committee
D04 - Road and Paving Materials
Drafting Committee
D04.34 - Preformed Joint Fillers, Sealers and Sealing Systems
Current Stage
Ref Project

Relations

Replaces
ASTM D2628-91(2011) - Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements
Effective Date
01-Oct-2016
Referred By
ASTM D5973-97(2017) - Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing
Effective Date
01-Oct-2016
Referred By
ASTM C1127/C1127M-15(2023) - Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
Effective Date
01-Oct-2016

Buy Standard

ASTM D2628-91(2016) - Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete PavementsASTM D2628-91(2016) - Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements
PreviousNext
Technical specification
ASTM D2628-91(2016) - Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D2628 −91 (Reapproved 2016)
Standard Specification for
Preformed Polychloroprene Elastomeric Joint Seals for
Concrete Pavements
This standard is issued under the fixed designation D2628; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope D518 Test Method for Rubber Deterioration—Surface
Cracking (Withdrawn 2007)
1.1 This specification covers the material requirements for
D573Test Method for Rubber—Deterioration in an Air
preformed polychloroprene elastomeric joint seals for concrete
Oven
pavements. The seal consists of a multiple web design and
D575Test Methods for Rubber Properties in Compression
functions only by compression of the seal between the faces of
D1149TestMethodsfor RubberDeterioration—Crackingin
the joint with the seal folding inward at the top to facilitate
an Ozone Controlled Environment
compression. The seal is installed with a lubricant and is
D2240Test Method for Rubber Property—Durometer Hard-
designed to seal the joint and reject incompressibles.
ness
1.2 The values stated in inch-pound units are to be regarded
D3183Practice for Rubber—Preparation of Pieces for Test
as standard. The values given in parentheses are mathematical
Purposes from Products
conversions to SI units that are provided for information only
and are not considered standard. 3. Materials and Manufacture
1.3 This standard does not purport to address the safety 3.1 The seals shall be preformed, and the material shall be
concerns, if any, associated with its use. It is the responsibility
vulcanized elastomeric compound using polychloroprene as
of the user of this standard to establish appropriate safety and the only base polymer.
health practices and determine the applicability of regulatory
4. Physical Requirements
limitations prior to use.
4.1 The materials shall conform to the physical properties
NOTE 1—This specification is a manufacturing and purchasing specifi-
prescribed in Table 1.
cation only and does not include requirements or considerations for
selectionofsize,ortheinstallationofthejointseals.However,experience
4.2 In the applicable requirements of Table 1 and the test
has shown that successful performance of this product depends upon the
methods,alldeflectionsshallbebasedonthenominalwidthof
proper selection of size and cross-sectional design of the joint seal, joint
the seal.
size, and joint spacing for the ambient conditions the pavement will be
exposed to, and care in the installation of the joint seals.
5. Dimensions and Permissible Variations
2. Referenced Documents
5.1 The size, shape, and dimensional variations shall be as
agreed upon by the purchaser and the producer or supplier.
2.1 ASTM Standards:
D395Test Methods for Rubber Property—Compression Set
6. Workmanship
D412TestMethodsforVulcanizedRubberandThermoplas-
6.1 Seals shall be free of defects in workmanship and
tic Elastomers—Tension
materials that may affect its serviceability.
D471Test Method for Rubber Property—Effect of Liquids
7. Sampling
7.1 Alot shall consist of the quantity for each cross section
This specification is under the jurisdiction ofASTM Committee D04 on Road
agreed upon by the purchaser and the producer or supplier.
and Paving Materials and is the direct responsibility of Subcommittee D04.34 on
Preformed Joint Fillers, Sealers and Sealing Systems.
7.2 Samplesshallbetakenatrandomfromeachshipmentof
Current edition approved Oct. 1, 2016. Published October 2016. Originally
material.Iftheshipmentconsistsofmorethanonelot,eachlot
approved in 1967. Last previous edition approved in 2011 as D2628–91(2011).
DOI: 10.1520/D2628-91R16.
shall be sampled.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D2628−91 (2016)
TABLE 1 Physical Requirements for Preformed Elastomeric Joint Seals
Property Requirement ASTM Test Method
Tensile strength, min, psi (MPa) 2000 (13.8) D412
Elongaton at break, min, % 250 D412
A
Hardness, Type A durometer, points 55 ± 5 D2240 (modified)
Oven aging, 70 h at 212°F (100°C) D573
Tensile strength, loss, max, % 20 max
Elongation, loss, max, % 20 max
Hardness, Type A durometer, points change 0 to + 10
Oil Swell, ASTM Oil 3, 70 h at 212°F (100°C) D471
Weight change, max, % 45 max
Ozone resistance D1149
B
20 % strain, 300 pphm in air, 70 h (modified)
at 104°F (40°C) no cracks
Low-temperature stiffening, 7 days at 14°F (−10°C) D2240
Hardness, Type A durometer, points change 0 to + 15
C
Low-temperature recovery, 72 h at 14°F (−10°C)
D
50 % deflection, min % 88 9.2
C D
Low-temperature recovery, 22 h at − 20°F (−29°C), 50 % deflection, 83 9.2
min %
C D
High-temperature recovery, 70 h at 212°F (100°C), 50 % deflec- 85 9.2
tion, min %
D
Compression-deflection, at 80 % of nominal width, min, lbf/in. (N/m) 3.5 (613) 9.3
A
The term “modified” in the table relates to the specimen preparation. The use of joint seal as the specimen source requires that more plies than specified in either of
themodifiedtestproceduresbeused.Suchspecimenmodificationshallbeagreeduponbythepurchaserandsellerpriortotesting.Thehardnesstestshallbemadewith
the durometer in a durometer stand as recommended in Test Method D2240.
B
Test in accordance with Procedure A of Test Method D518.
C
Cracking, splitting, or sticking of a specimen during a recovery test shall mean that the specimen has failed the test.
D
The reference sections are those of this specification.
7.3 A minimum of 9 linear ft (2.8 m) shall constitute one withSection8.Usetwospecimensforeachtestandrunthetest
sample for testing purposes. on both specimens at the same time as a pair.
9.2.2 Deflect the specimens between parallel plates to 50%
8. Specimen Preparation
of the nominal width of the seal using the compression device
8.1 Cut or buff all test specimens from the sample of
described in Method B of Test Methods D395. Prior to
preformed seal. Except as otherwise specified in the applicable
compression, place the specimen in a horizontal position such
specifications or test methods, prepare specimens in accor-
thattheplanethroughbothedgesofthetopsurfaceofthejoint
dance with the requirements of Practice D3183.
seal is perpendicular to the compression plates. As the speci-
men is being compressed, the top surface of the joint seal
8.2 Prepare specimens for determining tensile strength and
should fold inward toward the center of the specimen.
elongation using Die C (Test Methods D412) when possible.
9.2.3 Place a clamp assembly containing the compressed
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1752-18(2023)(Specification)
Standard Specification for Preformed Sponge Rubber, Cork, and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction

ABSTRACT
This specification covers preformed expansion joint fillers for use in concrete, brick, stone, and other paving and structural construction. The fillers are available in the following types: Type I, sponge rubber, which shall consist of preformed strips of a durable elastic sponge rubber compound using synthetic rubber or natural rubber as a base and containing no reclaim rubber or factice; Type II, cork, and Type III, self-expanding cork, which shall both consist of preformed strips that have been formed from clean granulated cork particles securely bound together by a synthetic resin of an incoluble nature; and Type IV, recycled PVC, which shall consist of preformed strips that have been extruded using scrap PVC material and using either no binder or a synthetic resin of an insoluble nature to securely bind it together. Materials shall be sampled suitably according to specified size and number, and shall meet property requirements as to recovery, compression, extrusion, expansion, boiling in hydrochloric acid, and density.
SCOPE
1.1 This specification covers preformed expansion joint fillers of the following four types for use in concrete, brick, or stone construction.  
1.1.1 Type I—Sponge rubber.  
1.1.2 Type II—Cork.  
1.1.3 Type III—Self-expanding cork.  
1.1.4 Type IV—Recycled PVC.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1: Attention is called to Specifications D994/D994M and D1751.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2950/D2950M-22(Test Method)
Standard Test Method for Density of Asphalt Mixtures in Place by Nuclear Methods

SIGNIFICANCE AND USE
4.1 The test method described is useful as a rapid, nondestructive technique for determining the in-place density of compacted asphalt mixtures.  
4.2 With proper calibration and confirmation testing, the test method is suitable for quality control and acceptance testing of compacted asphalt mixtures.  
4.3 The test method can be used to establish the proper rolling effort and pattern to achieve the required density.  
4.4 The nondestructive nature of the test allows repetitive measurements to be made at a single test location between roller passes and to monitor changes in density.  
4.5 The density results obtained by this test method are relative. Correlation with other test methods such as D1188/D1188M, D2726/D2726M, or D6752/D6752M is required to convert the results obtained using this method to actual density. It is recommended that at least seven core densities and seven nuclear densities be used to establish a conversion factor. A new factor must be established at any time a change is made in the paving mixture or in the construction process.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method describes a test procedure for determining the density of asphalt mixtures by the attenuation of gamma radiation, where the source and detector(s) remain on the surface (backscatter method) or the source or detector is placed at a known depth up to 300 mm [12 in.] while the detector or source remains on the surface (direct transmission method).  
1.2 The density, in mass per unit volume of the material under test, is determined by comparing the detected rate of gamma emissions with previously established calibration data.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 All observed and calculated values shall conform to the guide for significant digits and rounding established in Practice D6026.  
1.5 For limitations, see Section 5 on Interferences.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. It is the recommendation of Committee D04 that the following note be added to the end of the Significance and Use section of all applicable standards. Applicable standards are those in which measurement or calibration are made, sample are procured, or products are selected. The subcommittee shall determine the appropriateness of adding the note throughout the consensus process.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Develo...

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D979/D979M-22(Practice)
Standard Practice for Sampling Asphalt Mixtures

SIGNIFICANCE AND USE
4.1 General:  
4.1.1 Sampling is equally as important as the testing, and the sampler shall take every precaution to obtain samples that will yield an acceptable estimate of the nature and conditions of the materials which they represent.  
4.1.2 Samples for the development of preliminary data are obtained by the party responsible for the development of the data. Samples for control of the product at the source of manufacture or storage, or at the site of use, are obtained by the manufacturer, contractor, or other parties responsible for accomplishing the work. Samples for tests to be used in acceptance or rejection decisions by the purchaser are obtained by the purchaser or his authorized representative.  
4.1.3 This standard shall not be used for the sampling of compacted asphalt mixtures. Practice D5361/D5361M shall be used.
SCOPE
1.1 This practice covers sampling of asphalt mixtures at points of manufacture, storage, delivery, or in place.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D448-12(2022)(Classification)
Standard Classification for Sizes of Aggregate for Road and Bridge Construction

SIGNIFICANCE AND USE
4.1 Some contract documents specify certain aggregate sizes for specific uses or may suggest one or more of these sizes as appropriate for the preparation of various end-product mixtures. In some cases, closer limits on variability of the aggregate grading are required.
SCOPE
1.1 This classification defines aggregate size number designations and standard size ranges for mechanical sieve analyses of coarse aggregate and screenings for use in the construction and maintenance of various types of highways and bridges.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.  
1.3 The text of this classification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the classification.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1139/D1139M-22(Specification)
Standard Specification for Aggregate for Single or Multiple Asphalt Surface Treatments

ABSTRACT
This specification covers the quality and sizes of crushed stone, crushed slag, crushed expanded shale, crushed expanded clay, crushed expanded slate, and crushed or uncrushed gravel suitable for use as aggregate in single or multiple bituminous surface treatments. Tests shall be performed to determine the properties of the material in accordance with the following test methods: sampling; random sampling; degradation resistance; bulk density of aggregates; sulfate soundness; sieve analysis; clay lumps and friable particles; lightweight pieces; and flat and elongated pieces.
SCOPE
1.1 This specification covers the quality and sizes of crushed stone, crushed slag, crushed expanded shale, crushed expanded clay, crushed expanded slate, and crushed or uncrushed gravel suitable for use as aggregate in single or multiple asphalt surface treatments.  
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3.1 Regarding sieves, per Specification E11: “The values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth. The values stated in inch-pound units shall be considered standard with regard to the sieve frames.” When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1073-16(2022)(Specification)
Standard Specification for Fine Aggregate for Asphalt Paving Mixtures

ABSTRACT
This specification covers fine aggregate for use in bituminous paving mixtures. The aggregate shall be sampled to meet the requirements prescribed. Grading, fineness modulus and plasticity index shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers fine aggregate for use in asphalt paving mixtures.  
1.2 This specification is intended to describe material from a single source. When material from two or more sources is to be blended to produce a grading to meet requirements in other specifications for asphalt paving mixtures, the grading requirements of Table 1 of this specification are not applicable.  
Note 1: When obtaining materials from two or more sources that are to be blended to produce the final mix, it is recommended that the specifying or the ordering agency specify the alternative gradings and blend ratios to be supplied.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Sieve numbers shown in the text and Table 1 are labels only and are included for ease of reference of the user of this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8-22a(Terminology)
Standard Terminology Relating to Materials for Roads and Pavements

SCOPE
1.1 This standard incorporates generic terms and generic definitions of terms specifically associated with road and paving materials. These generic terms and definitions are used within the standards developed by Committee D04 on Road and Paving Materials.  
1.2 Only terms that appear in more than one standard under the jurisdiction of Committee D04 will be included in Section 3 of Terminology D8. Terms that were historically part of this terminology but never appeared, or no longer appear, in more than one standard under the jurisdiction of Committee D04 are listed in Appendix X1. The terms in Appendix X1 are not maintained and updated by Subcommittee D04.91. The terms in Appendix X1 are available for reference purposes only. The terminology in Appendix X1 may not reflect current practices, standards, and technology used in materials for roads and pavements.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3910-21(Practice)
Standard Practices for Design, Testing, and Construction of Slurry Seal

SIGNIFICANCE AND USE
4.1 These slurry seal practices are written as a guide and should not be construed as specifications.  
4.2 End-use specifications should be adopted to conform to job and user requirements.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 These practices cover the design, testing, and construction of mixtures for surface treatment of pavements. It is written as a guide and should be used as such. End-use specifications should be adapted to conform to job and user requirements.  
1.2 The values stated in SI units are to be regarded as the standard. The non-SI units used in this standard are allowed by the subcommittee for clarification in the use of the standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D4552/D4552M-20(Classification)
Standard Classification for Hot-Mix Recycling Agents

SIGNIFICANCE AND USE
3.1 Recycling of deteriorated asphalt pavements is being used with increasing frequency for its economy and benefit of conserving raw materials. The objective of recycling is to reuse the two ingredients of asphalt concrete-aggregate and asphalt binder and to restore the desired properties to the mixture. Recycling is carried out hot or cold, depending on the condition of the deteriorated pavement, construction procedure, availability of equipment, and cost. This classification is for classifying recycling agents to be used in recycled asphalt mixtures.  
Note 3: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This standard covers a standardized method whereby recycling agents to be used in hot recycling of asphalt concrete can be classified. The recycling agents are classified by viscosity in mm2/s measured at 60 °C [140 °F]. This classification does not apply to emulsified recycling agents.  
1.2 This standard does not address the performance of asphalt binder blends with recycling agents, or that of hot-mix asphalt mixture containing recycling agents. Adherence of a recycling agent to this specification does not necessarily relate to the performance of asphalt binders and mixtures containing the recycling agents.
Note 1: The impact of recycling agents has been evaluated by extracting the asphalt binder from the pavement to be recycled, and combining with the recycling agent to meet the appropriate grade within Specification D946/D946M or Table 1, 2, or 3 of Specification D3381/D3381M. More recently, some specifications have referred to performance grading as described in Specification D6373 or D8239.
Note 2: Efforts are underway to utilize performance-based testing of the asphalt mixture containing recycling agents as a measure of compliance.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off