ASTM F467-08

Standard Specification for Nonferrous Nuts for General Use

ABSTRACT
This specification covers the chemical, mechanical, dimensional, and workmanship and finish requirements, and the corresponding test methods for commercial wrought nonferrous nuts in a variety of alloys in common use that are intended for general service applications. When tested, the nuts shall meet required values for hardness, proof stress, and tensile stress areas.
SIGNIFICANCE AND USE
For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E 29.
SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications.  
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468.  
1.3 This specification is the inch-pound companion to Specification F 467M; therefore, no SI equivalents are presented in the specification.

General Information

• Status: Historical
• Publication Date: 30-Apr-2008
• ICS: 21.060.20 - Nuts
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.04 - Nonferrous Fasteners

Relations

• Replaces: ASTM F467-06ae1 - Standard Specification for Nonferrous Nuts for General Use
• Effective Date: 01-May-2008
• Replaced By: ASTM F467-08e1 - Standard Specification for Nonferrous Nuts for General Use
• Effective Date: 01-May-2008
• Referred By: ASTM F1718-01(2019) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
• Effective Date: 01-May-2008
• Referred By: ASTM F1370-92(2019)e1 - Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
• Effective Date: 01-May-2008
• Referred By: ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• Effective Date: 01-May-2008
• Referred By: ASTM C1802-23 - Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
• Effective Date: 01-May-2008
• Referred By: ASTM F1508-96(2021) - Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
• Effective Date: 01-May-2008
• Referred By: ASTM F468-23 - Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
• Effective Date: 01-May-2008
• Referred By: ASTM F1155-10(2019) - Standard Practice for Selection and Application of Piping System Materials
• Effective Date: 01-May-2008
• Referred By: ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• Effective Date: 01-May-2008

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F467 – 08
Standard Specification for
1
Nonferrous Nuts for General Use
ThisstandardisissuedunderthefixeddesignationF467;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* E54 Test Methods for ChemicalAnalysis of Special Brasses
3
and Bronzes
1.1 This specification covers the requirements for commer-
E55 Practice for Sampling Wrought Nonferrous Metals and
cial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in
Alloys for Determination of Chemical Composition
diameterinanumberofalloysincommonuseandintendedfor
E62 Test Methods for Chemical Analysis of Copper and
general service applications.
Copper Alloys (Photometric Methods)
1.2 Applicablebolts,capscrews,andstudsforusewithnuts
E75 Test Methods for ChemicalAnalysis of Copper-Nickel
covered by this specification are covered by Specification
and Copper-Nickel-Zinc Alloys
F468.
E76 Test Methods for ChemicalAnalysis of Nickel-Copper
1.3 This specification is the inch-pound companion to
3
Alloys
Specification F467M; therefore, no SI equivalents are pre-
E92 Test Method for Vickers Hardness of Metallic Materi-
sented in the specification.
als
2. Referenced Documents
E101 Test Method for Spectrographic Analysis of Alumi-
2
num and Aluminum Alloys by the Point-To-Plane Tech-
2.1 ASTM Standards:
3
nique
B154 Test Method for Mercurous Nitrate Test for Copper
E120 Test Methods for Chemical Analysis of Titanium and
Alloys
3
Titanium Alloys
B574 Specification for Low-Carbon Nickel-Chromium-
E165 PracticeforLiquidPenetrantExaminationforGeneral
Molybdenum, Low-Carbon Nickel-Molybdenum-
Industry
Chromium-Tantalum, Low-Carbon Nickel-Chromium-
E227 Test Method for Optical Emission Spectrometric
Molybdenum-Copper, and Low-Carbon Nickel-
Analysis of Aluminum and Aluminum Alloys by the
Chromium-Molybdenum-Tungsten Alloy Rod
3
Point-to-Plane Technique
D3951 Practice for Commercial Packaging
E354 Test Methods for Chemical Analysis of High-
E18 Test Methods for Rockwell Hardness of Metallic Ma-
Temperature, Electrical, Magnetic, and Other Similar Iron,
terials
Nickel, and Cobalt Alloys
E29 Practice for Using Significant Digits in Test Data to
E478 TestMethodsforChemicalAnalysisofCopperAlloys
Determine Conformance with Specifications
E1409 Test Method for Determination of Oxygen and
E34 Test Methods for ChemicalAnalysis ofAluminum and
Nitrogen in Titanium and TitaniumAlloys by the Inert Gas
Aluminum-Base Alloys
Fusion Technique
E38 Methods for Chemical Analysis of Nickel-Chromium
3
F468 Specification for Nonferrous Bolts, Hex Cap Screws,
and Nickel-Chromium-Iron Alloys
and Studs for General Use
E53 Test Method for Determination of Copper in Unalloyed
F606 Test Methods for Determining the Mechanical Prop-
Copper by Gravimetry
erties of Externally and Internally Threaded Fasteners,
Washers, Direct Tension Indicators, and Rivets
1
This specification is under the jurisdiction of ASTM Committee F16 on
F1470 Practice for Fastener Sampling for Specified Me-
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous
chanical Properties and Performance Inspection
Fasteners.
4
2.2 ASME Standards:
Current edition approved May 1, 2008. Published June 2008. Originally
´1
approved in 1976. Last previous edition approved in 2006 as F467 – 06a . DOI:
B 1.1 Unified Inch Screw Threads (UN and UNR Thread
10.1520/F0467-08.
Form)
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4
the ASTM website. Available from Global Engineering Documents, 15 Inverness Way, East
3
Withdrawn. Englewood, CO 80112-5704, http://global.ihs.com.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F467 – 08
B 18.2.2 Square and Hex Nuts 5.2 Manufacturer’s Analysis:
5.2.1 Except as provided in 5.2.2, when test reports are
3. Ordering Information
required on the inquiry or purchase order (3.1.8), the manu-
3.1 Orders for nuts under this specification shall include the
facturer shall make individual analyses of randomly selected
following information:
finished nuts from the product to be shipped and report the
3.1.1 Quantity (number of pieces of each item and size);
results to the purchaser. Alternatively, if heat and lot identities
3.1.2 Name of item;
have bee
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:F467–06a Designation: F 467 – 08
Standard Specification for
1
Nonferrous Nuts for General Use
This standard is issued under the fixed designation F 467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Table1 Nickel and Nickel-Base Alloys and Table 2 were editorially corrected in February 2008.
1. Scope*
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter
in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468.
Note1—A complete metric companion to Specification F467 has been developed—F467M; therefore no metric equivalents are
presented in this specification.
1.3 This specification is the inch-pound companion to Specification F 467M; therefore, no SI equivalents are presented in the
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
B 154 Test Method for Mercurous Nitrate Test for Copper Alloys
B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-
Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten
Alloy Rod
D 3951 Practice for Commercial Packaging
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
3
E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E92 Test Method for Vickers Hardness of Metallic Materials
0
E 101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-To-Plane Technique
E 120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
E 165 Test Method for Liquid Penetrant Examination
E 227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
Technique
E 354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and
Cobalt Alloys
E 478 Test Methods for Chemical Analysis of Copper Alloys
E 1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion
Technique
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners .
´1
Current edition approvedAug.May 1, 2006.2008. PublishedAugust 2006.June 2008. Originally approved in 1976. Last previous edition approved in 2006 as F 467 – 06a
.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F467–08
F 468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
F 606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers,
Direct Tension Indicators, and Rivets
F 1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
4
2.2 ASME Standards:
B 1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
B 18.2.2 Square and Hex Nuts
3. Ordering Information
3.1 Orders for nuts under this specification
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
e1
Designation:F467–06a Designation: F 467 – 08
Standard Specification for
1
Nonferrous Nuts for General Use
This standard is issued under the fixed designation F 467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Table1 Nickel and Nickel-Base Alloys and Table 2 were editorially corrected in February 2008.
1. Scope*
1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter
in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468.
Note1—A complete metric companion to Specification F467 has been developed—F467M; therefore no metric equivalents are
presented in this specification.
1.3 This specification is the inch-pound companion to Specification F 467M; therefore, no SI equivalents are presented in the
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
B 154 Test Method for Mercurous Nitrate Test for Copper Alloys
B 574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-
Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten
Alloy Rod
D 3951 Practice for Commercial Packaging
E 18 Test Methods for Rockwell Hardness of Metallic Materials
E 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E 34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
3
E 38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys
E 53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E 54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E 55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E 62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E 75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E 76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E 92 Test Method for Vickers Hardness of Metallic Materials
0
E 101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-To-Plane Technique
E 120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
E 165 Test Method for Liquid Penetrant Examination
E 227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
Technique
E 354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and
Cobalt Alloys
E 478 Test Methods for Chemical Analysis of Copper Alloys
E 1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion
Technique
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners .
´1
Current edition approvedAug.May 1, 2006.2008. PublishedAugust 2006.June 2008. Originally approved in 1976. Last previous edition approved in 2006 as F 467 – 06a
.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F467–08
F 468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
F 606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers,
Direct Tension Indicators, and Rivets
F 1470 Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
4
2.2 ASME Standards:
B 1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
B 18.2.2 Square and Hex Nuts
3. Ordering Information
3.1 Orders for nuts under this spec
...