iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1278/C1278M-03e1

(Specification)

Standard Specification for Fiber-Reinforced Gypsum Panel

Standard Specification for Fiber-Reinforced Gypsum Panel

SCOPE
1.1 This specification covers fiber-reinforced gypsum panels described in 1.1.1-1.1.4.
1.1.1 Interior Fiber-Reinforced Gypsum Panels are designed to be used for walls, ceilings, or partitions and affords a suitable surface to receive decoration.
1.1.2 Water Resistant Fiber-Reinforced Gypsum Backing Panels are designed primarily to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration.
1.1.3 Exterior Fiber-Reinforced Gypsum Soffit Panels are designed for use on exterior soffits and carport ceilings that are completely protected from contact with liquid water.
1.1.4 Water Resistant Exterior Fiber-Reinforced Gypsum Sheathing Panels are designed for use as sheathing on buildings.
1.2 Specifications applicable to all fiber-reinforced gypsum panels are located in Sections 1-4 and 9-11 except as modified by applicable product sections. Specifications applicable to specific panels are located in the following sections:Interior Fiber-Reinforced Gypsum Panels5Water-Resistant Fiber-Reinforced Gypsum Backing Panels6Exterior Fiber-Reinforced Gypsum Soffit Panels7Water-Resistant Exterior Fiber-Reinforced Gypsum Sheathing Panels8
1.3 The values stated in either inch-pound units or SI (metric) are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independently of the other. Values from the two systems shall not be combined.
1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard.

General Information

Status
Historical
Publication Date
30-Sep-2003
ICS
91.100.10 - Cement. Gypsum. Lime. Mortar
Technical Committee
C11 - Gypsum and Related Building Materials and Systems
Drafting Committee
C11.01 - Specifications and Test Methods for Gypsum Products
Current Stage
Ref Project

Relations

Replaces
ASTM C1278/C1278M-03 - Standard Specification for Fiber-Reinforced Gypsum Panel
Effective Date
01-Oct-2003
Replaced By
ASTM C1278/C1278M-06 - Standard Specification for Fiber-Reinforced Gypsum Panel
Effective Date
01-Nov-2006
Referred By
ASTM C1516-05(2023) - Standard Practice for Application of Direct-Applied Exterior Finish Systems
Effective Date
01-Oct-2003
Referred By
ASTM C1280-18 - Standard Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing
Effective Date
01-Oct-2003
Referred By
ASTM C1535-05(2023) - Standard Practice for Application of Exterior Insulation and Finish Systems Class PI
Effective Date
01-Oct-2003
Referred By
ASTM C1789-14(2018) - Standard Test Method for Calibration of Hand-Held Moisture Meters on Gypsum Panels
Effective Date
01-Oct-2003
Referred By
ASTM F1482-21 - Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
Effective Date
01-Oct-2003
Referred By
ASTM C1881-20 - Standard Guide for Closed-Loop Recycling of Scrap Gypsum Panel Products
Effective Date
01-Oct-2003
Referred By
ASTM C1397-13(2019) - Standard Practice for Application of Class PB Exterior Insulation and Finish Systems (EIFS) and EIFS with Drainage
Effective Date
01-Oct-2003

Buy Standard

ASTM C1278/C1278M-03e1 - Standard Specification for Fiber-Reinforced Gypsum PanelASTM C1278/C1278M-03e1 - Standard Specification for Fiber-Reinforced Gypsum Panel
PreviousNext
Technical specification
ASTM C1278/C1278M-03e1 - Standard Specification for Fiber-Reinforced Gypsum Panel
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
e1
Designation: C 1278/C 1278M – 03
Standard Specification for
1
Fiber-Reinforced Gypsum Panel
This standard is issued under the fixed designation C 1278/C 1278M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—The word rating(s) was added to the term fire resistance throughout editorially October 2004.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers fiber-reinforced gypsum pan- 2.1 ASTM Standards:
els described in 1.1.1-1.1.4. C 11 Terminology Relating to Gypsum and Related Build-
1.1.1 Interior Fiber-Reinforced Gypsum Panels are de- ing Materials and Systems
signed to be used for walls, ceilings, or partitions and affords C 22 Specification for Gypsum
a suitable surface to receive decoration. C 473 Test Methods for Physical Testing of Gypsum Panel
1.1.2 Water-Resistant Fiber-Reinforced Gypsum Backing Products
Panels are designed primarily to be used as a base for the C 645 Specification for Nonstructural Steel Framing Mem-
application of ceramic or plastic tile on walls or ceilings. This bers
product is also suitable for decoration. C 1264 Specification for Sampling, Inspection, Rejection,
1.1.3 Exterior Fiber-Reinforced Gypsum Soffıt Panels are Certification, Packaging, Marking, Shipping, Handling,
designed for use on exterior soffits and carport ceilings that are and Storage of Gypsum Board
completely protected from contact with liquid water. E 84 Test Method for Surface Burning Characteristics of
1.1.4 Water-Resistant Exterior Fiber-Reinforced Gypsum Building Materials
Sheathing Panels are designed for use as sheathing on build- E 96 Test Methods for Water Vapor Transmission of Mate-
ings. rials
1.2 Specifications applicable to all fiber-reinforced gypsum E 119 Test Methods for Fire Tests of Building Construction
panels are located in Sections 1-4 and 9-11 except as modified and Materials
by applicable product sections. Specifications applicable to
3. Terminology
specific panels are located in the following sections:
3.1 Definitions—Definitions of terms shall be in accordance
Interior Fiber-Reinforced Gypsum Panels 5
Water-Resistant Fiber-Reinforced Gypsum Backing Panels 6
with Terminology C 11.
Exterior Fiber-Reinforced Gypsum Soffit Panels 7
Water-Resistant Exterior Fiber-Reinforced Gypsum Sheathing Panels 8
4. Materials and Manufacture
1.3 The values stated in either inch-pound units or SI
4.1 Fiber-reinforced gypsum panels shall consist essentially
(metric) are to be regarded separately as the standard. Within
of gypsum with fibers dispersed throughout.
the text, the SI units are shown in brackets. The values stated
4.1.1 Gypsum—Specification C 22.
in each system shall be used independently of the other. Values
4.1.2 Fibers—Cellulose, derived from paper, paperboard
from the two systems shall not be combined.
stock, wood, or other organic material.
1.4 The text of this specification references notes and
4.2 Thebacksurfaceoffoil-backedfiber-reinforcedgypsum
footnotes that provide explanatory material. These notes and
panels shall in addition be covered with aluminum foil.
footnotes shall not be considered as requirements of the
4.3 Water-resistant fiber-reinforced gypsum panels shall be
standard.
treated with a material that imparts water resistance through-
out.
1
This specification is under the jurisdiction of ASTM Committee C11 on
Gypsum and Related Building Materials and Systems and is the direct responsi-
2
bility of Subcommittee C11.01 on Specifications and Test Methods for Gypsum For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Products. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved Oct. 1, 2003. Published November 2003. Originally Standards volume information, refer to the standard’s Document Summary page on
approvedin1994.Lastpreviouseditionapprovedin2001asC 1278/C 1278M – 01. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
e1
C 1278/C 1278M – 03
4.4 Fiber-reinforced gypsum panels, type X (special fire-
Thickness, in. [mm] Method B, lbf [N]
1
⁄4 [6.4] 40 [180]
resistant)designatesfiber-reinforcedgypsumpanelscomplying
5
⁄16 [7.9] 50 [220]
with this specification that provide not less than 1-h fire
3
⁄8 [9.5] 75 [335]
5 3
1
resistance rating for panels ⁄8-in. [15.9-mm] thick or ⁄4-h fire
⁄2 [12.7] 120 [535]
5
1 ⁄8 [15.9] 145 [645]
resistance rating for panels ⁄2-in. [12.7-mm] thick, applied
parallel
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C926-23a(Specification)
Standard Specification for Application of Portland Cement-Based Plaster

ABSTRACT
This specification covers the standard requirements for the application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. It also sets forth tables for proportioning of various plaster mixes and plaster thickness. The materials used shall consist of the following: cement which shall be a Portland cement, air-entraining Portland cement, masonry cement, blended hydraulic cement, air-entraining blended hydraulic cement, or plastic cement; Type S hydrated lime; aggregates such as perlite and sand for base and job-mixed finish coats; water to be used in mixing; admixtures; and fibers. Surfaces of solid bases such as masonry, stone, cast-in-place or precast concrete shall be prepared either by sandblasting, wire brushing, acid etching, chipping, or a combination thereof. Details on curing to resist cracking; materials protection and storage; environmental conditions; and application of plaster, finish-coat, and fog-coat, which shall be done by hand or machine up to the specified nominal thickness on metal and solid plaster bases are discussed.
SCOPE
1.1 This specification covers the minimum technical requirements for the application of full thickness portland cement-based plaster for exterior (stucco) and interior work. These requirements do not by default define a unit of work or assign responsibility for contractual purposes, which is the purview of a contract or contracts made between contracting entities.  
1.2 This specification sets forth tables for proportioning of various plaster mixes and plaster thickness.
Note 1: General information is found in Annex A1. Design considerations are found in Annex A2.  
1.3 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    14 pages
    English language
    sale 15% off
  • Technical specification
    14 pages
    English language
    sale 15% off
ASTM
ASTM C1861-23a(Specification)
Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster

ABSTRACT
This specification covers the minimum requirements for lathing and furring accessories and fasteners used as components of interior and exterior portland cement-based plaster assemblies for facilitating lathing and furring installation, cement plaster application, and functionality of the completed stucco cladding assembly. Lathing and furring accessories, and fasteners shall be free of deleterious amounts of rust, oil, or other foreign matter that could cause bond failure or unsightly discoloration; shall include key attachment flanges or solid attachment flanges; and shall be configured to accommodate application of the specified cement plaster thickness. Lathing accessories serving a drainage function shall include a drainage surface and a solid attachment flange. lathing accessories to facilitate drainage include weep screed, designated drainage screed, and perforations; lathing accessories to reinforce corners include internal corner reinforcement and external corner reinforcement; lathing accessories to reduce cracking include expansion joint and control joint; furring accessories include rod hanger, strap hanger, cold-rolled channel furring, and Z-furring.
SCOPE
1.1 This specification contains the minimum requirements for lathing and furring accessories, and fasteners, as components of interior and exterior portland cement-based plaster assemblies, used to facilitate lathing and furring installation (Specifications C1063, C1787), cement plaster application (Specification C926), and functionality of the completed stucco cladding assembly.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM C1280-18(2023)(Specification)
Standard Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing

ABSTRACT
This specification covers the minimum requirements for and the methods of application of gypsum sheathing for use as a substrate for exterior wall cladding. Gypsum sheathing board is a substrate that shall be covered by an exterior cladding or other weather-resistive barrier and is not intended for long-term exposure. Framing members shall be installed so that the surface will be in an even plane, unless otherwise specified, after the gypsum sheathing has been applied. The gypsum sheathing shall be cut by scoring and breaking or by sawing, working from the face side. The cut edges and ends of gypsum sheathing shall be trimmed to obtain neat fitting joints when installed. Gypsum sheathing shall be fitted snugly around all window and door openings. Control joints, other accessories, and metal plaster base shall be fastened through gypsum sheathing to framing members. Where fire resistance or shear resistance is not required, and when metal lath and Portland cement plaster are to be applied as the exterior cladding over gypsum sheathing installed over framing members and the metal lath shall be installed after the gypsum sheathing, the gypsum sheathing shall be permitted to be applied and fastening of the gypsum sheathing shall be completed with the attachment of the self-furred metal lath.
SCOPE
1.1 This specification covers the minimum requirements for and methods of application of exterior gypsum panel products that are specifically designed for use as a substrate for exterior cladding.  
1.1.1 This specification does not cover gypsum panel products that are specifically designed for interior applications.  
1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.  
1.2.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the fire-rated construction.  
1.3 Where sound control is required for a gypsum panel product assembly, the details of construction shall be in accordance with the acoustical test report of an assembly that has met the required acoustical value(s).  
1.3.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the sound-rated construction.  
1.4 Where resistance to racking loads or shear is required for a gypsum panel product assembly, the details of construction shall be in accordance with the racking or shear test report of an assembly that has met the required racking or shear value(s).  
1.4.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the racking or shear-tested construction.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1063-23(Specification)
Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster

ABSTRACT
This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases—expanded metal lath and wire laths; accessories—steel, PVC plastic, zinc alloy, and cornerite; channels—external corner reinforcement and foundation weep screed; wire; rod and strap hangers; clips; fasteners—nails and screws. Hangers and cold-rolled channel main runner shall conform to the allowable spacing and spans, respectively. The following methods are discussed: installation of hangers for suspended ceilings under wood constructions, attachment of hangers to main runners, installation of main runners, installation of cross furring, metal furring for walls, lapping of metal plaster bases, spacing of attachments for metal plaster bases, application of metal plaster bases, and application of accessories.
SCOPE
1.1 This specification covers the minimum technical requirements for the installation of lathing and furring for the application of exterior and interior portland cement-based plaster, as in Specification C926. These requirements do not by default define a unit of work or assign responsibility for contractual purposes, which is the purview of a contract or contracts made between contracting entities.  
1.2 Table of Contents:    
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Delivery and Storage of Materials  
4  
Materials  
5  
Requirements for Substrates to Receive Metal Lathing & Furring  
6  
Installation  
7  
Workmanship  
7.1  
Installation of Metal Furring for Walls  
7.2  
Installation of Metal Plaster Bases  
7.3  
Installation of Lathing Accessories  
7.4  
Keywords  
8  
Installation of Metal Furring for Suspended Ceilings  
Annex A1  
1.3 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.  
1.4 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable requirements of Test Method E90.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM C1787-23(Specification)
Standard Specification for Installation of Non Metallic Plaster Bases (Lath) Used with Portland Cement Based Plaster in Vertical Wall Applications

ABSTRACT
This specification describes the minimum requirements for the installation of non-metallic plaster bases used with portland cement-based plaster in vertical wall applications. In cases where a fire resistance rating is required for plastered assemblies and constructions, the construction details shall conform to reports of fire tests of assemblies that have satisfied the requirements of the fire rating imposed. The standard defines the requirements with respect to delivery and storage of materials, coordination and scheduling of installation, application of accessories, and application of non-metallic plaster bases.
SCOPE
1.1 This specification applies to the minimum installation requirements for non metallic plaster bases used with portland cement based plaster in vertical wall applications.  
1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.  
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 Details of construction for a specific assembly to achieve the required fire resistance, sound or acoustic rating shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing, sound or acoustic laboratories.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1860-23ce1(Test Method)
Standard Test Methods for Measurement of Tensile Strength or Bond Strength of Portland Cement-Based Plaster by Direct Tension

SIGNIFICANCE AND USE
4.1 The purpose of the test methods in this standard is to measure the tensile strength or bond strength of portland cement-based plaster to its substrate. The values obtained using the test methods are not purported to be representative of the actual wind load capacity or other structural properties of a specific portland cement-based plaster installation but may be helpful in assessing such load capacities.  
4.2 Because the test methods described in this standard are used for evaluation of portland cement-based plaster cured at least 28 days, load results obtained by either test method must be interpreted based on sound engineering practice, applicable building regulations, and codes having jurisdiction. The decision of whether to use the load results directly or to use the load results as modified by an appropriate safety factor to obtain acceptable working loads is left to the discretion of the test specifier. Determination of an appropriate safety factor shall be left to the discretion of the test specifier. Methods to calculate a safety factor and a maximum permitted working load are provided in the appendixes.  
4.3 When the test methods contained in this standard are used on test specimens installed on existing structures, the test results shall not be generalized to a larger wall area without sufficient test sampling. Such efforts should be based on engineering experience and judgment of the test specifier.
SCOPE
1.1 These test methods cover procedures for determining the tensile strength of a section of portland cement-based plaster, the bond strength between portland cement-based plaster and a solid plaster base, or the fastener pull-out or lath pull-over strength for portland cement-based plaster bases over framing in either an exterior (stucco) or interior application. The test procedures are destructive in nature within the localized test areas and, after testing is concluded, require appropriate repair of the finish system as well as any underlying materials damaged during testing.  
1.2 These test methods are suitable for use on portland cement-based plaster finish systems on both new and existing construction. Test methods shall be conducted a minimum of 28 days after application of the portland cement-based plaster. Mechanical Load Test Method A and Vacuum Chamber Testing shall be used to determine the tensile strength or bond strength of direct-applied portland cement-based plaster and may be useful in evaluating the efficacy of different surface preparation characteristics, bonding agents, or both. Mechanical Load Test Method B and Vacuum Chamber Testing shall be used to determine the tensile strength of portland cement-based plaster installed over mechanically attached lath.  
1.3 These test methods are suitable for use in both laboratory and field samples. No correlation shall be made between laboratory and field testing.  
1.4 These test methods are not intended to evaluate the performance of the underlying construction or framing members. Test results on a particular building may be variable depending on the specimen location, condition, and installation, and are subject to interpretation by the test specifier.  
1.5 These test methods are not intended to evaluate the performance of coatings applied to the surface of the portland cement-based plaster.  
1.6 These test methods are not intended to be a pre-construction qualifier to determine if the surfaces are appropriate for application of portland cement plaster. The test methods are intended to be used as a tool to quantitatively evaluate existing portland cement plaster cladding that is suspected of questionable bond or uncertain fastening to the substrate.  
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.8 This standard may involve...

  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM C1629/C1629M-23(Classification)
Standard Classification for Abuse-Resistant Nondecorated Interior Gypsum Panel Products and Fiber-Reinforced Cement Panels

SIGNIFICANCE AND USE
4.1 Each abuse/impact property of abuse resistant wall panels is divided into three classification levels. The three levels of classification are: Level I, Level II, and Level III, with Level I representing the lowest rating for any given property. The test methods specified are utilized to establish the abuse-resistance classification of an abuse resistant wall panel. Each classification level requires a minimum overall specified performance. Any classified abuse resistant wall panel can be used at a classification level which is rated lower than the highest level qualified.
SCOPE
1.1 This standard establishes classifications of abuse resistance based on the abrasion resistance and impact resistance performance of nondecorated interior gypsum panel products and fiber-reinforced cement panels (abuse resistant wall panels).  
1.1.1 This standard is a method of classifying gypsum panel product performance and is not intended to classify systems for abuse resistance.  
1.2 The values stated in inch-pound and SI (metric) units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM C843-23(Specification)
Standard Specification for Application of Gypsum Veneer Plaster

ABSTRACT
This specification covers the minimum requirements for gypsum veneer plaster and includes application methods on systems such as electric heat cable systems but not exceeding a specified temperature. Applicable building code regulations should be followed when a specific degree of fire resistance is required. Plaster and other cementitious materials should be kept dry until these are ready to be used and should be kept off the ground, under cover, and away from damp walls and surfaces.
SCOPE
1.1 This specification covers the minimum requirements for and methods of applying gypsum veneer plaster.  
1.2 Where a specific degree of fire resistance is required for veneer plaster systems, applicable building code regulations shall be followed.  
1.2.1 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.  
1.3 Where a specific degree of sound control is required for veneer plaster assemblies and constructions, details of construction shall be obtained from reports of acoustical tests of assemblies that have met the required or specified acoustical performance.
Note 1: To ensure desirable results, coordinate this specification with Specification C844.
Note 2: General information regarding matters of a contractual nature concerning veneer plaster work is found in Appendix X1. Additional technical information related to veneer plastering is provided in Appendix X2.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1381/C1381M-23(Specification)
Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts

ABSTRACT
This specification covers molded glass fiber reinforced gypsum (GRG) parts, which are nonload-bearing, thin-shell, ornamental shapes for architectural embellishment of interior building construction. GRG parts shall be produced using the same materials used to make the composites in conformance with the referenced specification. GRG parts shall be manufactured from the mixed slurry or alpha gypsum cement, potable water and additives, and glass fiber reinforcement using either the hand lay-up or the spray-up process in a mold. GRG parts shall be produced according to approved shop drawings. Shop drawings shall specify part dimensions, quantities, recommended attachment points and methods, reinforcements, embedments, and tolerance. The material shall conform to the required mechanical properties and to the specified dimensions and tolerances of GRG parts.
SCOPE
1.1 This specification covers molded glass fiber reinforced gypsum (GRG) parts, which are nonload-bearing, thin-shell, ornamental shapes for architectural embellishment of interior building construction.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The information presented refers to the molded surface of the part.  
1.4 The text of this standard references footnotes, which provide explanatory material. These footnotes shall not be considered as requirements of the standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM C841-23(Specification)
Standard Specification for Installation of Interior Lathing and Furring

ABSTRACT
This specification covers the minimum requirements for, and the methods of application of, interior lathing and furring to receive gypsum plaster applied. Other materials are not prohibited from being used provided that their physical characteristics and durability under conditions of usage are at least equal in performance to those described. All materials shall be kept dry, preferably by being stored inside. Where necessary to be stored outside, materials shall be stacked off the ground, supported on a level platform, and protected from the weather and surface contamination. Materials shall be neatly stacked flat with care taken to avoid damage to edges, ends, or surfaces. The materials to be used are the following: tie wire and hanger wire, gypsum lath, expanded metal lath, welded wire lath, woven wire lath, nails, screws, staples, paper, and accessories such as control joints, cornerite, channels, rod and flat hangers, clips, and striplath. In general, during installation, the following shall be required: application of gypsum lath to supports, application of gypsum lath to wood supports, application of gypsum lath to metal supports, studless solid partitions (gypsum lath and plaster), application of metal plaster bases to framing members, studless solid partitions (metal lath and plaster), suspended and furred ceilings (metal lath and gypsum lath construction), main runners, cross furring, and metal furring for walls.
SCOPE
1.1 This specification covers the minimum requirements for, and the methods of application of, interior lathing and furring to receive gypsum plaster applied in accordance with Specification C842. Other materials are not prohibited from being used provided that their physical characteristics and durability under conditions of usage are at least equal in performance to those described.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.  
1.4 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall be obtained from reports of acoustical tests of assemblies that have met the required or specified acoustical performance.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
  • Technical specification
    10 pages
    English language
    sale 15% off