ASTM B435-06(2016)

Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip

ABSTRACT
This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556 in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service. The material shall conform to the required chemical composition for nickel, iron, chromium, cobalt, molybdenum, tungsten, carbon, silicon, manganese, phosphorus, sulfur, columbium, tantalum, aluminum, zirconium, lanthanum, nitrogen, boron, and titanium. The alloy shall conform to specific mechanical requirements such as tensile strength, yield strength, and elongation. Annealed alloys UNS N06002, UNS N06230, and UNS R30556 sheet and strip shall conform to the grain size requirements.
SCOPE
1.1 This specification2 covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R305563 in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service.  
1.2 The following products are covered under this specification:  
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and descaled unless solution annealing is performed in an atmosphere yielding a bright finish.  
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2016
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B435 −06 (Reapproved 2016)
Standard Specification for
UNS N06002, UNS N06230, UNS N12160, and UNS R30556
1
Plate, Sheet, and Strip
This standard is issued under the fixed designation B435; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E527 Practice for Numbering Metals and Alloys in the
2 Unified Numbering System (UNS)
1.1 This specification covers alloys UNS N06002, UNS
3
N06230, UNS N12160, and UNS R30556 in the form of
3. Terminology
rolled plate, sheet, and strip for heat-resisting and general
corrosive service. 3.1 Definitions of Terms Specific to This Standard:
3
3.1.1 plate, n—material ⁄16 in. (4.76 mm) and over in
1.2 The following products are covered under this specifi-
thickness.
cation:
3
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and
3.1.2 sheet and strip, n—material under ⁄16 in. (4.76 mm) in
descaled unless solution annealing is performed in an atmo-
thickness.
sphere yielding a bright finish.
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.
4. General Requirements
1.3 The values stated in inch-pound units are to be regarded
4.1 Material furnished under this specification shall con-
as standard. The values given in parentheses are mathematical
form to the applicable requirements of Specification B906
conversions to SI units that are provided for information only
unless otherwise provided herein.
and are not considered standard.
1.4 This standard does not purport to address all of the
5. Ordering Information
safety concerns, if any, associated with its use. It is the
5.1 It is the responsibility of the purchaser to specify all
responsibility of the user of this standard to become familiar
requirements that are necessary for material ordered under this
with all hazards including those identified in the appropriate
specification. Examples of such requirements include, but are
Safety Data Sheet (SDS) for this product/material as provided
not limited to the following:
by the manufacturer, to establish appropriate safety and health
5.1.1 Alloy,
practices, and determine the applicability of regulatory limi-
5.1.2 Dimensions—Thickness (in decimals of an inch),
tations prior to use.
width, and length (inch or fraction of an inch),
5.1.3 Certification—State if certification or a report of test
2. Referenced Documents
resultsisrequired(SpecificationB906,sectiononMaterialTest
4
2.1 ASTM Standards:
Report an Certification),
B906 Specification for General Requirements for Flat-
5.1.4 Optional Requirement—Plate; state how plate is to be
Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
cut (Specification B906, Table titled Permissible Variations in
width and Length of Sheared, Torch-Cut, or Abrasive-Cut
Rectangular Plate),
1
This specification is under the jurisdiction of ASTM Committee B02 on
5.1.5 Purchase Inspection—State which tests or inspections
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys.
aretobewitnessed(SpecificationB906,sectiononInspection),
Current edition approved June 1, 2016. Published June 2016. Originally
and
ɛ1
approved in 1966. Last previous edition approved in 2011 as B435 – 06 (2011) .
5.1.6 Samples for Product (Check) Analysis—State whether
DOI: 10.1520/B0435-06R16.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi- samples should be furnished (Specification B906, section on
cation SB-435 in Section II of that Code.
Sampling).
3
New designation established in accordance with Practice E527 and SAE J1086,
Practice for Numbering Metals and Alloys (UNS).
4
6. Chemical Composition
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
6.1 The material shall conform to the requirements as to
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. chemical composition prescribed in Table 1.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B435−06 (2016)
TABLE 1 Chemical Requirements
Composition Limits, %
Element
UNS N06002 UNS N06230 UNS R30556 UNS N12160
Nickel remainder remainder 19.0–22.5 remainder
Iron 17.0–20.0 3.0 max remainder 3.5 max
Chromium 20.5–23.0 20.0–24.0 21.0–23.0 26.0–30.0
Cobalt 0.5–2.5 5.0 max 16.0–21.0 27.0–33.0
Molybdenum 8.0–10.0 1.0–3.00 2.5–4.0 1.0 max
Tungsten 0.2–1.0 13.0–15.0 2.0–3.5 1.0 max
Carbon 0.05–0.15 0.05–0.15 0.05–0.15 0.15 max
Silicon 1.00 max 0.25–0.75 0.2
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: B435 − 06 (Reapproved 2011) B435 − 06 (Reapproved 2016)
Standard Specification for
UNS N06002, UNS N06230, UNS N12160, and UNS R30556
1
Plate, Sheet, and Strip
This standard is issued under the fixed designation B435; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—The tensile strength for N12160 in Table 2 was editorially corrected in March 2014.
1. Scope
2 3
1.1 This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556*R30556 in the form of
rolled plate, sheet, and strip for heat-resisting and general corrosive service.
1.2 The following products are covered under this specification:
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and descaled unless solution annealing is performed in an atmosphere
yielding a bright finish.
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS)(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices,
and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
4
2.1 ASTM Standards:
B906 Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3
3.1.1 plate, n—material ⁄16 in. (4.76 mm) and over in thickness.
3
3.1.2 sheet and strip, n—material under ⁄16 in. (4.76 mm) in thickness.
4. General Requirements
4.1 Material furnished under this specification shall conform to the applicable requirements of Specification B906 unless
otherwise provided herein.
5. Ordering Information
5.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this
specification. Examples of such requirements include, but are not limited to the following:
5.1.1 Alloy,
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved June 1, 2011June 1, 2016. Published June 2011June 2016. Originally approved in 1966. Last previous edition approved in 20062011 as
ɛ1
B435 - 06.B435 – 06 (2011) . DOI: 10.1520/B0435-06R11E01.10.1520/B0435-06R16.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SB-435 in Section II of that Code.
* New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
3
New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B435 − 06 (2016)
5.1.2 Dimensions—Thickness (in decimals of an inch), width, and length (inch or fraction of an inch),
5.1.3 Certification—State if certification or a report of test results is required (Specification B906, section on Material Test
Report an Certification),
5.1.4 Optional Requirement—Plate; state how plate is to be cut (Specification B906, Table titled Permissible Variations in width
and Length of Sheared, Torch-Cut, or Abrasive-Cut Rectangular Plate),
5.1.5 Purchase Inspection—State which tests or inspections are to be witnessed (Specification B906, section on Inspection), and
5.1.6 Samples for Product (Check) Analysis—State whether samples should
...