ASTM B619-06

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

ABSTRACT
This specification covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS 06002; UNS N06022; UNS N06035; UNS N06058; UNS N06059; UNS N06200; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; UNS N06210; and UNS R20033). Two classes of pipe are covered as Class I which is as welded and solution annealed or welded and sized and solution annealed; and Class II which is welded, cold worked, and solution annealed. All pipes shall be furnished in the solution annealed and descaled condition. The pipe shall be made from flat-rolled alloy by an automatic welding process with no addition of filler metal. Subsequent to welding and prior to final heat treatment, Class II pipes shall be cold worked either in both weld and base metal or in weld metal only. The material shall conform to the composition limits set by this specification. Tensile strength, yield strength and elongation of the material shall conform to the mechanical requirements. Tension test, flattening test, transverse guided bend test, and hydrostatic or nondestructive electric test shall be performed.
SCOPE
1.1 This specification covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06035; UNS N06058; UNS N06059; UNS N06200; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)* as shown in Table 1.
1.2 This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size and larger as set forth in ANSI B36.19 (see Table 2).
1.3 Two classes of pipe are covered as follows:
1.3.1 Class IAs welded and solution annealed or welded and sized and solution annealed.
1.3.2 Class II Welded, cold worked, and solution annealed.
1.4 All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2006
• ICS: 23.040.15 - Non-ferrous metal pipes
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B619 – 06
Standard Specification for
1
Welded Nickel and Nickel-Cobalt Alloy Pipe
This standard is issued under the fixed designation B619; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2 3
1.1 This specification covers welded pipe of nickel and 2.1 ASTM Standards:
nickel-cobalt alloys (UNS N10001; UNS N10242; UNS B775 Specification for General Requirements for Nickel
N10665; UNS N12160; UNS N10624; UNS N10629; UNS and Nickel Alloy Welded Pipe
N10675; UNS N10276; UNS N06455; UNS N06007; UNS B899 Terminology Relating to Non-ferrous Metals and
N06975; UNS N08320; UNS N06002; UNS N06022; UNS Alloys
N06035; UNS N06058; UNS N06059; UNS N06200; UNS E527 Practice for Numbering Metals and Alloys in the
N06985; UNS N06030; UNS R30556; UNS N08031; UNS Unified Numbering System (UNS)
4
N06230; UNS N06686; UNS N06210; and UNS R20033)* as 2.2 ANSI Standards:
shown in Table 1. B36.19 Stainless Steel Pipe
1.2 This specification covers pipe in Schedules 5S, 10S, B2.1 Pipe Threads
5
40S, and 80S through 8-in. nominal pipe size and larger as set 2.3 ASME Boiler and Pressure Vessel Code
forth in ANSI B36.19 (see Table 2). Section IX Welding and Brazing Qualifications
1.3 Two classes of pipe are covered as follows:
3. Terminology
1.3.1 Class I—As welded and solution annealed or welded
and sized and solution annealed. 3.1 For definitions of terms used in this standard refer to
Terminology B899.
1.3.2 Class II—Welded, cold worked, and solution an-
nealed.
4. General Requirement
1.4 All pipe shall be furnished in the solution annealed and
4.1 Material furnished under this specification shall con-
descaled condition. When atmosphere control is used, descal-
form to the applicable requirements of Specification B775
ing is not necessary.
unless otherwise provided herein.
1.5 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
5. Ordering Information
information only.
5.1 It is the responsibility of the purchaser to specify all
1.6 This standard does not purport to address all of the
requirements that are necessary for material ordered under this
safety concerns, if any, associated with its use. It is the
specification. Examples of such requirements include, but are
responsibility of the user of this standard to become familiar
not limited to the following:
with all hazards including those identified in the appropriate
5.1.1 Alloy (Table 1),
Material Safety Data Sheet (MSDS) for this product/material
5.1.2 Class (see 1.3),
as provided by the manufacturer, to establish appropriate
5.1.3 Quantity (feet or number of lengths),
safety and health practices, and determine the applicability of
5.1.4 Size (nominal size or outside diameter and schedule
regulatory limitations prior to use.
number or average wall thickness),
1
This specification is under the jurisdiction of ASTM Committee B02 on
3
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee For referenced ASTM standards, visit the ASTM website, www.astm.org, or
B02.07 on Refined Nickel and Cobalt and Their Alloys. contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Current edition approved June 1, 2006. Published June 2006. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1981. Last previous edition approved in 2005 as B619 – 05. DOI: the ASTM website.
4
10.1520/B0619-06. Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- 4th Floor, New York, NY 10036.
5
cation SB-619 in Section II of that Code. Available from American Society of Mechanical Engineers (ASME), ASME
* NewdesignationestablishedinaccordancewithPracticeE527andSAEJ1086, International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
Practice for Numbering Metals and Alloys (UNS). www.asme.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B619 – 06
5.1.5 Length—Specify cut length or random, 8.3.3 The bend test shall be acceptable if no cracks or other
1
5.1.6 Certification—State if certification or a report of test defects exceeding ⁄8 in. (3 mm) in any direction be present in
results is required, the weld metal or between the weld and the pipe or plate metal
5.1.7 Purchaser Inspection—State which tests or inspec- after bending. Cracks which originate along the edges of the
1
tions are
...