iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6451/D6451M-99(2014)e1

(Guide)

Standard Guide for Application of Asphalt Based Protection Board

Standard Guide for Application of Asphalt Based Protection Board

SIGNIFICANCE AND USE
4.1 This guide outlines general procedures for the storage and application of semi-rigid protection board to below grade and below wearing surface waterproofing. The proper application is necessary to prevent damage to the waterproofing membrane during backfilling, paving, or other construction operations, as well as to minimize the effects of soil stresses.  
4.2 This guide is intended to supplement instructions from designers and manufacturers.
SCOPE
1.1 This guide lists minimum application and installation requirements for semi-rigid protection board when used as protection for below grade or below wearing surface (like plaza decks) waterproofing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this guide to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statement, see Section 8.

General Information

Status
Historical
Publication Date
30-Apr-2014
ICS
91.060.99 - Other elements of buildings
Technical Committee
D08 - Roofing and Waterproofing
Drafting Committee
D08.22 - Waterproofing and Dampproofing Systems
Current Stage
Ref Project

Buy Standard

ASTM D6451/D6451M-99(2014)e1 - Standard Guide for Application of Asphalt Based Protection BoardASTM D6451/D6451M-99(2014)e1 - Standard Guide for Application of Asphalt Based Protection Board
PreviousNext
Guide
ASTM D6451/D6451M-99(2014)e1 - Standard Guide for Application of Asphalt Based Protection Board
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D6451/D6451M − 99 (Reapproved 2014)
Standard Guide for
Application of Asphalt Based Protection Board
This standard is issued under the fixed designation D6451/D6451M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
ε NOTE—Units information was editorially corrected in May 2014.
1. Scope tion is necessary to prevent damage to the waterproofing
membrane during backfilling, paving, or other construction
1.1 This guide lists minimum application and installation
operations, as well as to minimize the effects of soil stresses.
requirements for semi-rigid protection board when used as
protectionforbelowgradeorbelowwearingsurface(likeplaza 4.2 This guide is intended to supplement instructions from
decks) waterproofing. designers and manufacturers.
1.2 The values stated in either SI units or inch-pound units
5. Delivery of Materials
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each 5.1 Deliver materials in supplier’s original containers and
packaging.
system shall be used independently of the other. Combining
values from the two systems may result in non-conformance
6. Storage and Handling
with the standard.
1.3 This standard does not purport to address all of the 6.1 Store adhesive and mastic in tightly closed original
safety concerns, if any, associated with its use. It is the containers under conditions as recommended by the manufac-
responsibility of the user of this guide to establish appropriate turer.
safety and health practices and determine the applicability of
6.2 Store the protection board in supplier’s original pack-
regulatory limitations prior to use. For specific precautionary
aging in a horizontal position to prevent deformation. Protect
statement, see Section 8.
against exposure to direct sunlight, precipitation, dust, and
other such contaminants.
2. Referenced Documents
2.1 ASTM Standards:
7. Materials
D1079 Terminology Relating to Roofing and Waterproofing
7.1 Adhesive, when used, must be acceptable to or have
D5957 Guide for Flood Testing Horizontal Waterproofing
been recommended by the waterproofing membrane manufac-
Installations
turer or supplier and further must be fully compatible with the
membrane and the asphalt protection board.
3. Terminology
7.2 Mastic or tape, or both, (if used on the joints) must be
3.1 Definitions—For definitions of terms relating to
acceptable to or have been recommended by the waterproofing
waterproofing, see Terminology D1079.
membrane manufacturer or supplier and further be fully
4. Significance and Use
compatible with the membrane and the asphalt protection
board.
4.1 This guide outlines general procedures for the storage
and application of semi-rigid protection board to below grade
8. Safety Precautions
and below wearing surface waterproofing. The proper applica-
8.1 Store flammable materials in a manner that will not pose
a fire hazard. Solvent bearing adhesives may be flammable. Do
This guide is under the jurisdiction of ASTM Committee D08 on Roofing and
Waterproofing and is the direct responsibility of Subcommittee D08.22 on Water- not use flammable materials near an open flame or equipment
proofing and Dampproofing Systems.
that may produce sparks.
Current edition approved May 1, 2014. Published May 2014. Originally
approved in 1999. Last previous edition approved in 2006 as D6451 – 99 (2006).
9. Environmental Conditions at Time of Application
DOI: 10.1520/D6451_D6451M-99R14E01.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
9.1 Environmental conditions under which installation may
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
proceed shall be as recommended by the suppliers of the
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. adhesive and the protection board.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
´1
D6451/D6451M − 99 (2014)
10. Substrate Preparation 11.3.1 The protection board is to be applied with the long
axis of the board going up the slope. The joints in the
10.1 The waterproofing membrane must be clean and suf-
cross-the-slope direction shall be aligned while the up-slope
ficiently dry so as not to interfere with adhesion of the
joints shall be in a stacked brick pattern, with joints centered
protection board.
over previously applied boards.
10.2 If a flood test of the membrane is desired, this test
11.3.2 Using adhesive as described in 7.2, coat the outside
should be made before placing the protection co
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6451/D6451M-99(2021)(Guide)
Standard Guide for Application of Asphalt-Based Protection Board

SIGNIFICANCE AND USE
4.1 This guide outlines general procedures for the storage and application of semi-rigid protection board to below-grade and below wearing surface waterproofing. The proper application is necessary to prevent damage to the waterproofing membrane during backfilling, paving, or other construction operations, as well as to minimize the effects of soil stresses.  
4.2 This guide is intended to supplement instructions from designers and manufacturers.
SCOPE
1.1 This guide lists minimum application and installation requirements for semi-rigid protection board when used as protection for below-grade or below wearing surface (like plaza decks) waterproofing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 8.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6506/D6506M-01(2018)e1(Specification)
Standard Specification for Asphalt Based Protection Board for Below-Grade Waterproofing

ABSTRACT
This specification covers the manufacture, testing, and physical requirements of two classes of asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. Class A is made with asphalt saturated organic felt on the bottom and a coated or saturated non-woven glass felt on top, while Class B is made with glass fabrics both top and bottom. The boards shall be sampled for testing, and each class shall conform accordingly to specified individual values of the following physical properties: nominal thickness; puncture strength; water absorption; asphalt content; and resistance to decay.
SCOPE
1.1 This specification covers an asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. The protection board protects the waterproofing system from backfill, surfacing, construction activities, and weathering conditions prior to backfilling or applying surfacing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6451/D6451M-99(2021)(Guide)
Standard Guide for Application of Asphalt-Based Protection Board

SIGNIFICANCE AND USE
4.1 This guide outlines general procedures for the storage and application of semi-rigid protection board to below-grade and below wearing surface waterproofing. The proper application is necessary to prevent damage to the waterproofing membrane during backfilling, paving, or other construction operations, as well as to minimize the effects of soil stresses.  
4.2 This guide is intended to supplement instructions from designers and manufacturers.
SCOPE
1.1 This guide lists minimum application and installation requirements for semi-rigid protection board when used as protection for below-grade or below wearing surface (like plaza decks) waterproofing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 8.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off
ASTM
ASTM E1190-21(Test Method)
Standard Test Methods for Strength of Power-Actuated Fasteners Installed in Structural Members

SIGNIFICANCE AND USE
4.1 These test methods are intended to measure the anchoring capability and shear resistance of power-actuated fasteners to provide information from which applicable design values are to be derived for use in structural applications, such as in members of concrete, concrete masonry, and steel.
SCOPE
1.1 These test methods describe procedures for determining the static axial tensile and shear strengths of power-actuated fasteners installed in structural members made of concrete, concrete masonry, and steel.  
1.2 These test methods are intended for use with fasteners that are installed perpendicular to a plane surface of the structural member.  
1.3 Tests for combined tension and shear, fatigue, dynamic, and torsional load resistance are not covered.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 6.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6506/D6506M-01(2018)e1(Specification)
Standard Specification for Asphalt Based Protection Board for Below-Grade Waterproofing

ABSTRACT
This specification covers the manufacture, testing, and physical requirements of two classes of asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. Class A is made with asphalt saturated organic felt on the bottom and a coated or saturated non-woven glass felt on top, while Class B is made with glass fabrics both top and bottom. The boards shall be sampled for testing, and each class shall conform accordingly to specified individual values of the following physical properties: nominal thickness; puncture strength; water absorption; asphalt content; and resistance to decay.
SCOPE
1.1 This specification covers an asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. The protection board protects the waterproofing system from backfill, surfacing, construction activities, and weathering conditions prior to backfilling or applying surfacing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2697-15(Test Method)
Standard Test Methods for Physical Assault on Overhead Horizontal Fixed Barriers for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administrative officials is the security of barriers used in detention/correctional facilities. These test methods are designed to aid in identifying levels of physical security for horizontal fixed barriers, which serve to enclose or separate secure areas. This does not apply to the passage of contraband or vandalism.  
4.2 These test methods are not intended to provide a measure of resistance for a ceiling subjected to attack by corrosive agents, by high-powered rifles, explosives, sawing, or other such methods not typically available to inmates. These test methods are intended to evaluate the resistance of a ceiling to violent attacks by sustained manpower using battering devices, such as benches, barbells, bunks, or tables; and by an upward static force such that could be applied by an inmate pushing against the ceiling with his hands, feet, or back (that is, squat position on a top bunk in a cell). Attacks from outside the facility and fire resistance ratings are not addressed in this standard.  
4.3 The primary purpose or result of these test methods is to approximate the levels of abuse to which horizontal fixed barriers could possibly be subjected in the field. The desired result of its use is to help provide assurance of protection to the public, to facility personnel, and to the inmates themselves.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision, and preventive maintenance programs to enable horizontal fixed barriers to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of horizontal fixed barriers designed to incarcerate inmates in detention and correctional institutions. The testing equipment provides for the setup and testing of sample barriers and installation systems.  
1.2 It is the intent of these test methods to help ensure that detention security horizontal fixed barriers perform at or above minimum acceptable levels for control of passage to unauthorized or secure areas, to confine inmates, and to delay and frustrate escape attempts. Provide security grilles, access doors, light fixtures, and similar assemblies compatible with these levels of performance, with test apparatus adjustments as required to suit the particular product.  
1.3 These test methods apply to horizontal fixed barriers enclosing or separating secure areas of detention/correctional facilities.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversion to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D6152/D6152M-12(2024)(Specification)
Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing

ABSTRACT
This specification covers SEBS (styrene-ethylenebutylene-styrene)-modified mopping asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roofing systems. This specification is intended as a material specification and issues regarding the suitability of specific roof constructions or application techniques are beyond its scope. The specified tests and property values are intended to establish minimum properties. In place system design criteria or performance attributes are factors beyond the scope of this specification. The base asphalt shall be prepared from crude petroleum and the SEBS-modified asphalt shall incorporate sufficient SEBS as the primary polymeric modifier. The SEBS modified asphalt shall be homogeneous and free of water and shall conform to the prescribed physical properties including (1) softening point before and after heat exposure, (2) softening point change, (3) flash point, (4) penetration before and after heat exposure, (5) penetration change, (6) solubility in trichloroethylene, (7) tensile elongation, (8) elastic recovery, and (9) low temperature flexibility. The sampling and test methods to determine compliance with the specified physical properties, as well as the evaluation for stability during heat exposure are detailed.
SCOPE
1.1 This specification covers SEBS (styrene-ethylene-butylene-styrene)-modified asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roof systems.  
1.2 This specification is intended as a material specification. Issues regarding the suitability of specific roof constructions or application techniques are beyond its scope.  
1.3 The specified tests and property values used to characterize SEBS-modified asphalt are intended to establish minimum properties. In-place system design criteria or performance attributes are factors beyond the scope of this specification.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5643/D5643M-06(2024)(Specification)
Standard Specification for Coal Tar Roof Cement, Asbestos Free

ABSTRACT
This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems. The chemical composition of coal tar roof cement shall conform to the requirements prescribed. The water, non-volatile matter, insoluble matter, behaviour at 60 deg. C, adhesion to wet surfaces, and flash point shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D396-24(Specification)
Standard Specification for Fuel Oils

ABSTRACT
This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small industrial burners; Grades No. 1 S5000 and No. 1 S500 adapted to vaporizing type burners or where storage conditions require low pour point fuel; Grades No. 4 (Light) and No. 4 (Heavy) for use in commercial/industrial burners; and Grades No. 5 (Light), No. 5 (Heavy), and No. 6 for use in industrial burners. Preheating is usually required for handling and proper atomization. The grades of fuel oil shall be homogeneous hydrocarbon oils, free from inorganic acid, and free from excessive amounts of solid or fibrous foreign matter. Grades containing residual components shall remain uniform in normal storage and not separate by gravity into light and heavy oil components outside the viscosity limits for the grade. The grades of fuel oil shall conform to the limiting requirements prescribed for: (1) flash point, (2) water and sediment, (3) physical distillation or simulated distillation, (4) kinematic viscosity, (5) Ramsbottom carbon residue, (6) ash, (7) sulfur, (8) copper strip corrosion, (9) density, and (10) pour point. The test methods for determining conformance to the specified properties are given.
SCOPE
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows:  
1.1.1 Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2 S15 are middle distillate fuels for use in domestic and small industrial burners. Grades No. 1 S5000, No. 1 S500, and No. 1 S15 are particularly adapted to vaporizing type burners or where storage conditions require low pour point fuel.  
1.1.2 Grades B6–B20 S5000, B6–B20 S500, and B6–B20 S15 are middle distillate fuel/biodiesel blends for use in domestic and small industrial burners.  
1.1.3 Grades No. 4 (Light) and No. 4 are heavy distillate fuels or middle distillate/residual fuel blends used in commercial/industrial burners equipped for this viscosity range.  
1.1.4 Grades No. 5 (Light), No. 5 (Heavy), and No. 6 are residual fuels of increasing viscosity and boiling range, used in industrial burners. Preheating is usually required for handling and proper atomization.  
Note 1: For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
Note 2: A more detailed description of the grades of fuel oils is given in X1.3.  
1.2 This specification is for the use of purchasing agencies in formulating specifications to be included in contracts for purchases of fuel oils and for the guidance of consumers of fuel oils in the selection of the grades most suitable for their needs.  
1.3 Nothing in this specification shall preclude observance of federal, state, or local regulations which can be more restrictive.  
1.4 The values stated in SI units are to be regarded as standard.  
1.4.1 Non-SI units are provided in Table 1 and Table 2 and in 7.1.2.1/7.1.2.2 because these are common units used in the industry.
Note 3: The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM D8165-24(Test Method)
Standard Test Method for Evaluation of Load-Carrying Capacity of Lubricants Used in Hypoid Final-Drive Axles Operated under Low-Speed and High-Torque Conditions

SIGNIFICANCE AND USE
5.1 This test method measures a lubricant's ability to protect hypoid final drive axles from abrasive wear, adhesive wear, plastic deformation, and surface fatigue when subjected to low-speed, high-torque conditions. Lack of protection can lead to premature gear or bearing failure, or both.  
5.2 This test method is used, or referred to, in specifications and classifications of rear-axle gear lubricants such as:  
5.2.1 Specification D7450.  
5.2.2 American Petroleum Institute (API) Publication 1560.  
5.2.3 SAE J308.  
5.2.4 SAE J2360.
SCOPE
1.1 This test method, commonly referred to as the L-37-1 test, describes a test procedure for evaluating the load-carrying capacity, wear performance, and extreme pressure properties of a gear lubricant in a hypoid axle under conditions of low-speed, high-torque operation.3  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct SI equivalent such as National Pipe threads/diameters, tubing size, or where there is a sole source supply equipment specification.
1.2.1.1 The drawing in Annex A6 is in inch-pound units.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are provided in 7.2 and 10.1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off