ASTM F1163-04
(Specification)Standard Specification for Protective Headgear Used in Horse Sports and Horseback Riding
Standard Specification for Protective Headgear Used in Horse Sports and Horseback Riding
SCOPE
1.1 This specification covers minimum performance criteria and describes test methods for protective headgear for use in horse sports and horseback riding.
1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at the time of development of this specification.
1.3 All testing and requirements of this specification shall be in accordance with Test Methods F 1446, except where noted herein.
1.4 The values stated in SI units are to be regarded as standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1163 – 04
Standard Specification for
Protective Headgear Used in Horse Sports and Horseback
1
Riding
This standard is issued under the fixed designation F 1163; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Horse sports and horseback riding are sports with intrinsic hazards. It is recognized that it is not
possible to write a protective headgear performance standard that will result in headgear that can
protect against injury or death in all accidents. It is also recognized that serious injury or death can
result from both low-energy and high-energy impacts, even when protective headgear is worn. It is
further recognized that protective headgear must be acceptable to the user and to the regulating
associations or agencies requiring its use. Acknowledging these limitations, this specification was
developed using resources in medical, scientific, mechanical engineering, human factors, and
biomechanical fields.
This specification incorporates many aspects of other recognized headgear performance standards.
This specification draws from work done by others where appropriate for this specification. These
standards may be referenced. It should be noted that this specification specifies a laboratory test of
completed headgear to measure its ability to reduce head acceleration when impacting various shaped
objects. It is known that headgear that performs well under this specification will mitigate head injury
in actual use within its design limits.
1. Scope 2. Referenced Document
2
1.1 This specification covers minimum performance criteria 2.1 ASTM Standards:
and describes test methods for protective headgear for use in F 1446 Test Methods for Equipment and Procedures Used
horse sports and horseback riding. inEvaluatingthePerformanceCharacteristicsofProtective
1.2 It is not the intention of this specification to bar from Headgear
considerationmaterialsofimprovedqualityorperformancenot
3. Terminology
known at the time of development of this specification.
3.1 Definitions—The terms used in this specification are
1.3 All testing and requirements of this specification shall
be in accordance with Test Methods F 1446, except where defined in accordance with Test Methods F 1446.
3.2 Definitions of Terms Specific to This Standard:
noted herein.
1.4 The values stated in SI units are to be regarded as 3.2.1 cradle, n—headband or other head-fitting device and
those internal parts of the headgear in contact with the head.
standard.
3.2.2 drawlace, n—lace used for making adjustments to the
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the fit of the cradle on the wearer’s head.
responsibility of the user of this standard to establish appro-
4. Headforms
priate safety and health practices and determine the applica-
4.1 Headforms to be used in this specification are in
bility of regulatory limitations prior to use.
accordance with the section on Apparatus of Test Methods
1
This specification is under the jurisdiction ofASTM Committee F08 on Sports
2
Equipment and Facilities and is the direct responsibility of Subcommittee F08.53 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Headgear and Helmets. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved June 1, 2004. Published June 2004. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1988. Last previous edition approved in 2001 as F 1163 – 01.
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F1163–04
F 1446. The appropriate size headform shall be selected (see 6. General Requirements and Marking
definition of headform size selection in the Terminology
6.1 Select the appropriate reference headform in accordance
section of Test Methods F 1446) for the helmet to be tested.
with the definition of headform size selection in the Terminol-
ogy section of Test Methods F 1446.
5. Anvils and Impact Velocities
6.2 Position the helmet in accordance with the section on
5.1 Anvils to be used for impact tests in this specification Test Procedures of Test Methods F 1446.
are the flat anvil described in the section and figure on Flat
6.3 All helmets shall meet the requirements of the sections
Anvil of Test Methods F 1446, and the equestrian hazard anvil
on Configuration, Materials, and Internal Projection of Test
described in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.