ASTM F667/F667M-16(2021)
(Specification)Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings
Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings
ABSTRACT
This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, bond, and marking of corrugated polyethylene (PE) pipe and fittings. This specification covers tubularly extruded, spirally laminated, and rotationally molded corrugated polyethylene pipe. Corrugated PE pipe and fittings are intended for underground applications where soil provides support to their flexible walls. Their major use is to collect or convey drainage water, or both. The following tests shall be performed: dimensions and tolerances; pipe stiffness; elongation; pipe stiffness while elongated; joint-separation test; and brittleness.
SCOPE
1.1 This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, bond, and marking of corrugated polyethylene (PE) pipe and fittings. It covers nominal sizes 3 in. [76 mm], 4 in. [102 mm], 5 in. [127 mm] 6 in. [152 mm], 8 in. [203 mm], 10 in. [254 mm], 12 in. [305 mm], 15 in. [381 mm], 18 in. [457 mm], and 24 in. [610 mm].
1.2 This specification covers tubularly extruded, spirally laminated, and rotationally molded corrugated polyethylene pipe.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F667/F667M −16 (Reapproved 2021)
Standard Specification for
1
3 through 24 in. Corrugated Polyethylene Pipe and Fittings
This standard is issued under the fixed designation F667/F667M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D2412Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.1 This specification covers requirements and test methods
D2444Practice for Determination of the Impact Resistance
for materials, workmanship, dimensions, perforations, pipe
of Thermoplastic Pipe and Fittings by Means of a Tup
stiffness, elongation, joint separation resistance, quality of
(Falling Weight)
extruded polyethylene, brittleness, bond, and marking of cor-
D3350Specification for Polyethylene Plastics Pipe and Fit-
rugated polyethylene (PE) pipe and fittings. It covers nominal
tings Materials
sizes 3 in. [76 mm], 4 in. [102 mm], 5 in. [127 mm] 6 in. [152
F412Terminology Relating to Plastic Piping Systems
mm],8in.[203mm],10in.[254mm],12in.[305mm],15in.
F449Practice for Subsurface Installation of Corrugated
[381 mm], 18 in. [457 mm], and 24 in. [610 mm].
Polyethylene Pipe for Agricultural Drainage or Water
1.2 This specification covers tubularly extruded, spirally
Table Control
laminated, and rotationally molded corrugated polyethylene
3
2.2 Federal Standard:
pipe.
Fed. Std. No. 123Marking for Shipment (Civil Agencies)
1.3 The values stated in inch-pound units are to be regarded
3
2.3 Military Standard:
as standard. The values given in parentheses are mathematical
MIL-STD-129Marking for Shipment and Storage
conversions to SI units that are provided for information only
and are not considered standard.
3. Terminology
1.4 The following precautionary caveat pertains only to the
3.1 Definitions—Definitions used in this specification are in
test method portion, Section 9, of this specification: This
accordance with Terminology F412, unless otherwise noted.
standard does not purport to address all of the safety concerns,
if any, associated with its use. It is the responsibility of the user
3.2 Definitions:
of this standard to establish appropriate safety, health, and
3.2.1 split—any break or crack that extends through the
environmental practices and determine the applicability of
wall.
regulatory limitations prior to use.
3.2.2 crease—a deformation that cannot be removed like a
1.5 This international standard was developed in accor-
dent: generally associated with wall buckling.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
4. Significance and Use
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
4.1 Corrugated PE pipe and fittings are intended for under-
Barriers to Trade (TBT) Committee.
ground applications where soil provides support to their
flexible walls.Their major use is to collect or convey drainage
2. Referenced Documents
water, or both.
2
2.1 ASTM Standards:
4.2 Exclusions from Recommended Use:
D618Practice for Conditioning Plastics for Testing
4.2.1 Exposure to flame at any time,
4.2.2 Permanent exposure to sunlight or weathering, or
1 both, and
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land
4.2.3 Exposure to chemicals, other than those normally
Drainage.
found in ground water, whose compatibility with the tubing
Current edition approved April 1, 2021. Published April 2021. Originally
and fittings is not known.
approved in 1980. Last previous edition approved in 2016 as F667/F667M–16.
DOI: 10.1520/F0667_F0667M-16R21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA
the ASTM website. 19111-5094 http://quicksearch.dla.mil/
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F667/F667M − 16 (2021)
5. Materials and circumference of the pipe in a size, shape, and pattern
suited to the needs of the user.
5.1 Bas
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.