ASTM A387/A387M-11
(Specification)Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum
Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum
ABSTRACT
This specification covers chromium-molybdenum alloy steel plates for welded boilers and pressure vessels designed for elevated temperature service. Materials considered under this specification are available in grades 2, 12, 11, 22, 22L, 21, 21L, 5, 9 and 91. The steel materials shall be killed and shall be thermally treated. The steel specimens shall undergo heat analysis and product analysis and shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, nickel, vanadium, columbium, boron, nitrogen, aluminum, titanium, and zirconium. The steel specimens shall also undergo tension tests and shall conform to the required values of tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification covers chromium-molybdenum alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A387/A387M −11 Used in USDOE-NE Standards
Standard Specification for
Pressure Vessel Plates, Alloy Steel, Chromium-
1
Molybdenum
This standard is issued under the fixed designationA387/A387M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
3
2
2.1 ASTM Standards:
1.1 This specification covers chromium-molybdenum alloy
A20/A20M SpecificationforGeneralRequirementsforSteel
steel plates intended primarily for welded boilers and pressure
Plates for Pressure Vessels
vessels designed for elevated temperature service.
A370 Test Methods and Definitions for Mechanical Testing
1.2 Plates are available under this specification in several
of Steel Products
grades having different alloy contents as follows:
A435/A435M Specification for Straight-Beam Ultrasonic
Nominal Nominal
Examination of Steel Plates
Chromium Molybdenum
A577/A577M Specification for Ultrasonic Angle-Beam Ex-
Grade Content, % Content, %
amination of Steel Plates
2 0.50 0.50
12 1.00 0.50
A578/A578M Specification for Straight-Beam Ultrasonic
11 1.25 0.50
Examination of Rolled Steel Plates for Special Applica-
22, 22L 2.25 1.00
21, 21L 3.00 1.00 tions
5 5.00 0.50
A1017/A1017M Specification for Pressure Vessel Plates,
9 9.00 1.00
Alloy Steel, Chromium-Molybdenum-Tungsten
91 9.00 1.00
4
2.2 AWS Specifications:
1.3 Each grade except Grades 21L, 22L, and 91 is available
A5.5/A5.5M Low-Alloy Steel Electrodes for Shielded Metal
intwoclassesoftensilestrengthlevelsasdefinedintheTensile
Arc Welding
Requirements tables. Grades 21Land 22Lare available only as
A5.23/A5.23M Low-Alloy Steel Electrodes and Fluxes for
Class 1. Grade 91 is available only as Class 2.
Submerged Arc Welding
NOTE 1—Grade 911, previously covered by this specification, is now
A5.28/A5.28M Low-Alloy Steel Electrodes and Rods for
covered by Specification A1017/A1017M.
Gas Shielded Arc Welding
1.4 The maximum thickness of plates is limited only by the
A5.29/A5.29M Low-Alloy Steel Electrodes for Flux Cored
capacity of the composition to meet the specified mechanical
Arc Welding
property requirements.
3. General Requirements and Ordering Information
1.5 The values stated in either inch-pound units or SI units
3.1 Material supplied to this material specification shall
are to be regarded separately as standard. Within the text, the
conform to Specification A20/A20M. These requirements out-
SI units are shown in brackets. The values stated in each
line the testing and retesting methods and procedures, permis-
system are not exact equivalents. Therefore, each system must
sible variations in dimensions and weight, quality and repair of
be used independently of the other. Combining values from the
defects, marking, loading, and ordering information.
two systems may result in nonconformance with this specifi-
cation.
3.2 In addition to the basic requirements of this
specification, certain supplementary requirements are available
when additional control, testing, or examination is required to
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
3
A01.11 on Steel Plates for Boilers and Pressure Vessels. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2011. Published April 2011. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1955. Last previous edition approved in 2010 as A387/A387M – 10. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A0387_A0387M-11. the ASTM website.
2 4
For ASME Boiler and Pressure Vessel Code applications, see related Specifi- Available from American Welding Society (AWS), 550 NW LeJeune Rd.,
cation SA-387/SA-387M in Section II of that Code. Miami, FL 33126, http://www.aws.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A387/A387M−11
meet end use requirements. The purchaser is referred to the VacuumCarbon-DeoxidizedSteel,inSpecificationA20/A20M
listed supplementary requirements in this specification and to for grades other than Grade 11.
the detailed requirements in Specification A20/A20M.
7. Metallurgical Structure
3.3 If the requirements of this specification are in conflict
7.1 Austenitic Grain Size—Grade 2 material s
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE Standards
Designation:A387/A387M–10 Designation: A387/A387M – 11
Standard Specification for
Pressure Vessel Plates, Alloy Steel, Chromium-
1
Molybdenum
This standard is issued under the fixed designationA387/A387M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers chromium-molybdenum alloy steel plates intended primarily for welded boilers and pressure
vessels designed for elevated temperature service.
1.2 Plates are available under this specification in several grades having different alloy contents as follows:
Nominal Nominal
Chromium Molybde-
num
Grade Content, % Content, %
2 0.50 0.50
12 1.00 0.50
11 1.25 0.50
22, 22L 2.25 1.00
21, 21L 3.00 1.00
5 5.00 0.50
9 9.00 1.00
91 9.00 1.00
1.3 Each grade except Grades 21L, 22L, and 91 is available in two classes of tensile strength levels as defined in the Tensile
Requirements tables. Grades 21L and 22L are available only as Class 1. Grade 91 is available only as Class 2.
NOTE 1—Grade 911, previously covered by this specification, is now covered by Specification A1017/A1017M.
1.4 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical
property requirements.
1.5 Thevaluesstatedineitherinch-poundunitsorSIunitsaretoberegardedseparatelyasstandard.Withinthetext,theSIunits
are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with this specification.
2. Referenced Documents
3
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
A578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
A1017/A1017M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten
4
2.2 AWS Specifications:
A5.5/A5.5M Low-Alloy Steel Electrodes for Shielded Metal Arc Welding
A5.23/A5.23M Low-Alloy Steel Electrodes and Fluxes for Submerged Arc Welding
A5.28/A5.28M Low-Alloy Steel Electrodes and Rods for Gas Shielded Arc Welding
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Oct.April 1, 2010.2011. Published November 2010.April 2011. Originally approved in 1955. Last previous edition approved in 20062010 as
A387/A387M–06a.A387/A387M – 10. DOI: 10.1520/A0387_A0387M-101.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-387/SA-387M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Welding Society (AWS), 550 NW LeJeune Rd., Miami, FL 33126, http://www.aws.org.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A387/A387M – 11
A5.29/A5.29M Low-Alloy Steel Electrodes for Flux Cored Arc Welding
3. General Requirements and Ordering Information
3.1 Material supplied to this material specification shall conform to Specification A20/A20M. These requirements outline the
testing and retesting methods and procedures, permissible variations in dimensions and weight, quality and repair of defects,
marking, loading, and ordering information.
3.2 In addition to the basic requirements of this specification, certain supplementary requirements are available when additional
control, testing, or examination is required to meet end use requirements. The purchaser is referred to the li
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE Standards
Designation:A387/A387M–10 Designation: A387/A387M – 11
Standard Specification for
Pressure Vessel Plates, Alloy Steel, Chromium-
1
Molybdenum
This standard is issued under the fixed designationA387/A387M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers chromium-molybdenum alloy steel plates intended primarily for welded boilers and pressure
vessels designed for elevated temperature service.
1.2 Plates are available under this specification in several grades having different alloy contents as follows:
Nominal Nominal
Chromium Molybde-
num
Grade Content, % Content, %
2 0.50 0.50
12 1.00 0.50
11 1.25 0.50
22, 22L 2.25 1.00
21, 21L 3.00 1.00
5 5.00 0.50
9 9.00 1.00
91 9.00 1.00
1.3 Each grade except Grades 21L, 22L, and 91 is available in two classes of tensile strength levels as defined in the Tensile
Requirements tables. Grades 21L and 22L are available only as Class 1. Grade 91 is available only as Class 2.
NOTE 1—Grade 911, previously covered by this specification, is now covered by Specification A1017/A1017M.
1.4 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical
property requirements.
1.5 Thevaluesstatedineitherinch-poundunitsorSIunitsaretoberegardedseparatelyasstandard.Withinthetext,theSIunits
are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with this specification.
2. Referenced Documents
3
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
A578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
A1017/A1017M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten
4
2.2 AWS Specifications:
A5.5/A5.5M Low-Alloy Steel Electrodes for Shielded Metal Arc Welding
A5.23/A5.23M Low-Alloy Steel Electrodes and Fluxes for Submerged Arc Welding
A5.28/A5.28M Low-Alloy Steel Electrodes and Rods for Gas Shielded Arc Welding
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Oct.April 1, 2010.2011. Published November 2010.April 2011. Originally approved in 1955. Last previous edition approved in 20062010 as
A387/A387M–06a.A387/A387M – 10. DOI: 10.1520/A0387_A0387M-101.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-387/SA-387M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Welding Society (AWS), 550 NW LeJeune Rd., Miami, FL 33126, http://www.aws.org.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A387/A387M – 11
A5.29/A5.29M Low-Alloy Steel Electrodes for Flux Cored Arc Welding
3. General Requirements and Ordering Information
3.1 Material supplied to this material specification shall conform to Specification A20/A20M. These requirements outline the
testing and retesting methods and procedures, permissible variations in dimensions and weight, quality and repair of defects,
marking, loading, and ordering information.
3.2 In addition to the basic requirements of this specification, certain supplementary requirements are available when additional
control, testing, or examination is required to meet end use requirements. The purchaser is referred to the li
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.