ASTM F467M-05

Standard Specification for Nonferrous Nuts for General Use [Metric]

SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications.
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F 468M.
Note 1—This specification is the metric companion of Specification F 467.

General Information

• Status: Historical
• Publication Date: 30-Sep-2005
• ICS: 21.060.20 - Nuts
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.04 - Nonferrous Fasteners

Relations

• Replaces: ASTM F467M-03a - Standard Specification for Nonferrous Nuts for General Use [Metric]
• Effective Date: 01-Oct-2005
• Replaced By: ASTM F467M-06 - Standard Specification for Nonferrous Nuts for General Use [Metric]
• Effective Date: 01-May-2006
• Referred By: ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• Effective Date: 01-Oct-2005
• Referred By: ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• Effective Date: 01-Oct-2005
• Referred By: ASTM F468M-06(2018) - Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
• Effective Date: 01-Oct-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 467M – 05
METRIC
Standard Specification for
1
Nonferrous Nuts for General Use [Metric]
This standard is issued under the fixed designation F 467M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope Copper Alloys (Photometric Methods)
E 75 Test Methods for ChemicalAnalysis of Copper-Nickel
1.1 This specification covers the requirements for commer-
and Copper-Nickel-Zinc Alloys
cial wrought nonferrous nuts in nominal thread diameters M6
E 76 Test Methods for Chemical Analysis of Nickel–Cop-
to M36 inclusive in a number of alloys in common use and
3
per Alloys
intended for general service applications.
E92 Test Method for Vickers Hardness of Metallic Mate-
1.2 Applicablebolts,capscrews,andstudsforusewithnuts
rials
covered by this specification are covered by Specification
E 101 Test Method for Spectrographic Analysis of Alu-
F 468M.
minum and Aluminum Alloys by the Point-to-Plane Tech-
NOTE 1—This specification is the metric companion of Specification 3
nique
F 467.
E 120 Test Methods for ChemicalAnalysis of Titanium and
3
Titanium Alloys
2. Referenced Documents
E 165 Practice for Liquid Penetrant Examination
2
2.1 ASTM Standards:
E 227 Test Method for Optical Emission Spectrometric
B 154 Test Method for Mercurous Nitrate Test for Copper
Analysis of Aluminum and Aluminum Alloys by the
and Copper Alloys
3
Point-to-Plane Technique
D 3951 Practice for Commercial Packaging
E 354 Test Methods for Chemical Analysis of High-
E18 Test Methods for Rockwell Hardness and Rockwell
Temperature, Electrical, Magnetic, and Other Similar Iron,
Superficial Hardness of Metallic Materials
Nickel, and Cobalt Alloys
E29 Practice for Using Significant Digits in Test Data to
E 478 Test Methods for Chemical Analysis of Copper
Determine Conformance with Specifications
Alloys
E 34 Test Methods for ChemicalAnalysis ofAluminum and
E 1409 Test Method for Determination of Oxygen in Tita-
Aluminum-Base Alloys
nium and Titanium Alloys by the Inert Gas Fusion Tech-
E 38 Methods for Chemical Analysis of Nickel-Chromium
nique
3
and Nickel-Chromium-Iron Alloys
F 468M Specification for Nonferrous Bolts, Hex Cap
E 53 Test Methods for Determination of Copper in Unal-
Screws, and Studs for General Use [Metric]
loyed Copper by Gravimetry
F 606M Test Methods for Determining the Mechanical
E 54 Test Methods for Chemical Analysis of Special
Properties of Externally and InternallyThreaded Fasteners,
3
Brasses and Bronzes
Washers, and Rivets [Metric]
E55 PracticeforSamplingWroughtNonferrousMetalsand
F 1470 GuideforFastenerSamplingforSpecifiedMechani-
Alloys for Determination of Chemical Composition
cal Properties and Performance Inspection
E 62 Test Methods for Chemical Analysis of Copper and
4
2.2 ASME Standards:
B 1.13M Metric Screw Threads
1
B 18.2.4.1M Metric Hex Nuts, Style 1
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous
3. Ordering Information
Fasteners.
Current edition approved Oct. 1, 2005. Published October 2005. Originally
3.1 Orders for nuts under this specification shall include the
approved in 1979. Last previous edition approved in 2003 as F 467M – 03a.
2
following information:
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4
the ASTM website. Available from Global Engineering Documents, 15 Inverness Way, East
3
Withdrawn. Englewood, CO 80112-5704.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F467M–05
3.1.1 Quantity (numbers of pieces of each item and size);
Nickel alloys 400 and As formed or stress relieved at manufacturer’s option
405
3.1.2 Name of item;
Nickel alloy 500 Solution annealed and aged
3.1.3 Nominal thread diameter and thread pitch;
Aluminum alloys:
3.1.4 Alloy number (Table 1); 2024-T4 Solution treated and naturally aged
6061-T6 Solution treated and artificially aged
3.1.5 Stress relieving, if required (4.2.3);
6262-T9 Solution treated, artificially aged, and cold worked
3.1.6 “Shipment lot” testing, as required (Section 9);
Titanium As formed
3.1.7 Source inspection, if required (Section 14);
4.2.3 Stress Relieving—When required, stress relieving
3.1.8 Certificate of compliance or test report, if required
shall be specified by
...