iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3785-02

(Specification)

Standard Performance Specification for Woven Necktie and Scarf Fabrics

Standard Performance Specification for Woven Necktie and Scarf Fabrics

SCOPE
1.1 This performance specification covers woven necktie and scarf fabrics composed of any textile fiber or mixture of textile fibers.
1.2 This performance specification is not applicable to woven fabrics used for interlinings.
1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.
1.4The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-May-2002
ICS
61.040 - Headgear. Clothing accessories. Fastening of clothing
Technical Committee
D13 - Textiles
Drafting Committee
D13.61 - Apparel
Current Stage
Ref Project

Relations

Replaces
ASTM D3785-95 - Standard Performance Specification for Woven Necktie and Scarf Fabrics
Effective Date
10-May-2002
Replaced By
ASTM D3785-02(2008) - Standard Performance Specification for Woven Necktie and Scarf Fabrics
Effective Date
01-Aug-2008

Buy Standard

ASTM D3785-02 - Standard Performance Specification for Woven Necktie and Scarf FabricsASTM D3785-02 - Standard Performance Specification for Woven Necktie and Scarf Fabrics
PreviousNext
Technical specification
ASTM D3785-02 - Standard Performance Specification for Woven Necktie and Scarf Fabrics
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 3785 – 02
Standard Performance Specification for
1
Woven Necktie and Scarf Fabrics
This standard is issued under the fixed designation D 3785; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
3
1. Scope 2.2 AATCC Methods:
8-1974 Colorfastness to Crocking: AATCC Crockmeter
1.1 This performance specification covers woven necktie
Method
and scarf fabrics composed of any textile fiber or mixture of
15-1976 Colorfastness to Perspiration
textile fibers.
16-1974 Colorfastness to Light
1.2 This performance specification is not applicable to
23-1975 Colorfastness to Burnt Gas Fumes
woven fabrics used for interlinings.
61-1975 Colorfastness to Washing, Domestic, and Launder-
1.3 These requirements apply to the length and width
ing, Commercial: Accelerated
directions for those properties where fabric direction is perti-
96-1975 DimensionalChangesinLaunderingofWovenand
nent.
Knitted Textiles Except Wool
1.4 The following precautionary caveat pertains only to the
116-1974 ColorfastnesstoCrocking:RotaryVerticalCrock-
test methods portion, Section 7, of this specification. This
meter Method
standard does not purport to address all of the safety concerns,
124-1975 Appearance of Durable Press Fabrics After Re-
if any, associated with its use. It is the responsibility of the user
peated Home Launderings
of this standard to establish appropriate safety and health
132-1976 Colorfastness to Drycleaning
practices and determine the applicability of regulatory limita-
135-1973 Dimensional Changes inAutomatic Home Laun-
tions prior to use.
dering of Durable Press Woven or Knit Fabrics
2. Referenced Documents 172 Colorfastness to Non-Chlorine Bleach in Home Laun-
2
dering
2.1 ASTM Standards:
188 Colorfastness to Sodium Hypochlorite Bleach in Home
D 123 Terminology Relating to Textiles
Laundering
D 434 Test Method for Resistance to Slippage of Yarns in
Evaluation Procedure 1 Gray Scale for Color Change
Woven Fabrics Using a Standard Seam
Evaluation Procedure 2 Gray Scale for Staining
D 1336 Test Method for Distortion of Yarn in Woven
Evaluation Procedure 3 AATCC Chromatic Transference
Fabrics
Scale
D 1424 Test Method for Tear Resistance of Woven Fabrics
by Falling-Pendulum (Elmendorf) Apparatus
NOTE 1—Reference to test methods in this specification give only the
D 1682 Test Methods for Breaking Load and Elongation of
permanent part of the designation of ASTM, AATCC, or other test
Textile Fabrics methods. The current editions of each test method cited shall prevail.
D 2262 Test Method for Tearing Strength of Woven Fabrics
3. Terminology
by the Tongue (Single Rip) Method (Constant-Rate-of-
3.1 Definitions:
Traverse Tensile Testing Machine)
3.1.1 scarf—in apparel, an oblong or square piece of cloth
D 2724 Test Methods for Bonded, Fused, and Laminated
worn for warmth or as a decorative item.
Apparel Fabrics
3.2 For definitions of textile terms used in this specification,
D 2905 Practice for Statements on Number of Specimens
refer to Terminology D 123 and the Technical Manual of the
for Textiles
3
American Association of Textile Chemists and Colorists.
1
This specification is under the jurisdiction of ASTM Committee D13 on 4. Specification Requirements
Textiles and is the direct responsibility of Subcommittee D13.61 on Apparel.
4.1 The properties of fabrics for woven neckties and scarfs
Current edition approved May 10, 2002. Published June 2002. Originally
shall conform to the specification requirements in Table 1.
published as D 3785 – 79. Last previous edition D 3785 – 95.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from theAmericanAssociation of Textile Chemists and Colorists, P.
the ASTM website. O. Box 12215, Research Triangle Park, NC 27709.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3785–02
TABLE 1 Specification Requirements
6. Sampling
NOTE 1—Class in colorfastness and DP requirements is based on a 6.1 Testsshallbeperformedonthefabricasitwillreachthe
numerical scale of 5 for negligible or no color change, color transfer, or
consumer.
fabric wrinkle to 1 for severe color change, color transfer, or fabric
6.2 Unless otherwise agreed upon, as when specified in an
wrinkle.
applicablematerialspecification,takethenumberofspecimens
Characteristic Requirements Section
directed in each of the applicable test
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2050-23(Terminology)
Standard Terminology Relating to Fastener Subassemblies Used in the Manufacture of Textiles

SCOPE
1.1 This standard identifies terminology related to subassemblies which are categorized as any component that is used in the construction or assembly of a textile product. Subassemblies can be in the form of components used as closures (for example, slide fasteners, buttons, snap fasteners, hook and loop (touch) fasteners) or methods used to join textile sections (for example, stitches and seams).  
1.2 Terms relating to Buttons are found in Section 3.  
1.3 Terms relating to Hook and Loop (Touch) fasteners are in Section 4.  
1.4 Terms relating to Snap Fasteners are found in Section 5.  
1.5 Terms relating to Slide Fasteners are found in Section 6.  
1.6 For other terms related to textiles, refer to Terminology D123.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D4153-22(Specification)
Standard Performance Specification for Men's, Women's, and Children's Woven Handkerchief Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4153 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics to be used in the manufacture of men's, women's, and children's handkerchiefs, both utilitarian and decorative.  
1.2 This performance specification is not applicable to open-work fabrics such as lace which is used primarily to decorate handkerchiefs, or woven fabrics used for the manufacture of scarves.  
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4035-22(Specification)
Standard Performance Specification for Knitted Necktie and Scarf Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4035 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers knitted necktie and scarf fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2053-99(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Light

SIGNIFICANCE AND USE
5.1 This test method is useful in determining if the loss of color due to light exposure is satisfactory for the intended end-use.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The test method(s) in this standard along with those in Test Methods D2051, D2052, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and...
SCOPE
1.1 This test method covers the determination of the alteration in shade of the textile portion of zippers when exposed to light, regardless of the materials of manufacture.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2052-05(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Drycleaning

SIGNIFICANCE AND USE
5.1 Test Method D2052 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur.
Note 1: For guidance in evaluating the results of this test method, refer to Practice D3692.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in this standard along with those in Test Methods D2051, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been publishe...
SCOPE
1.1 This test method covers the determination of change in shade and of staining of zipper stringers under drycleaning conditions. This test method is applicable to the textile portion of zipper stringers of all materials.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2058-03(2022)(Test Method)
Standard Test Method for Durability of Finish of Zippers to Drycleaning

SIGNIFICANCE AND USE
5.1 Test Method D2058 is useful for determining the effect of repeated drycleaning on the appearance of the decorative coating of a zipper.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2059, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thoroug...
SCOPE
1.1 This test method covers the determination of the durability of the enamel or other decorative coating of zippers when subjected to drycleaning.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2060-14(2022)(Test Method)
Standard Test Methods for Measuring Zipper Dimensions

SIGNIFICANCE AND USE
4.1 The significance of specific tests is discussed in the appropriate sections.  
4.2 These test methods are considered satisfactory for acceptance testing of commercial shipments because the test methods have been used extensively in the trade for this purpose, and because current estimates of between-laboratory precision are acceptable in most cases.  
4.2.1 In case of a dispute arising from differences in reported test results when using Test Methods D2060 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias if found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.  
4.3 The test method(s) in these test methods, along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2058, D2059, D2061, and D2062, are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either be...
SCOPE
1.1 These test methods cover the measurement of the dimensions of all types and sizes of zippers.  
1.2 The test methods appear as follows:    
Sections  
Chain Flatness  
34 – 39  
Chain Straightness  
40 – 44  
Chain Thickness  
28 – 33  
Chain Width  
45 – 50  
Length of Zipper or Parts  
9 – 14  
Longitudinal Dimensional Change  
51 – 58  
Slider Mouth Width  
21 – 27  
Tape Width  
15 – 20  
1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D2057-05(2022)(Test Method)
Standard Test Method for Colorfastness of Zippers to Laundering

SIGNIFICANCE AND USE
5.1 Test Method D2057 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur.
Note 1: For guidance in evaluating the results of this method, refer to Practice D3692.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in this standard along with those in D2051, D2052, D2053, D2054, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because...
SCOPE
1.1 This test method covers the determination of alteration in shade and of staining under conditions similar to that experienced in domestic washing of zipper stringers. This test method is applicable to the textile portion of zipper stringers that utilize tapes made of cotton, linen, or manufactured organic fibers, and to combinations thereof.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2059/D2059M-03(2022)(Test Method)
Standard Test Method for Resistance of Zippers to Salt Spray (Fog)

SIGNIFICANCE AND USE
5.1 The resistance of a zipper to a variety of saline and non-saline environments can be estimated from the amount and nature of corrosion products and their effect on operability. Results of exposure to the salt spray are merely indicative of the reaction to other corrosive conditions. While the results cannot be related precisely to a given length of exposure in a specific atmosphere, they are useful for measuring relative performance under prescribed conditions for controlling a manufacturing process, and for measuring the effectiveness of protective coatings.  
5.2 Test Method D2059 for the determination of the resistance of zippers to salt spray is considered satisfactory for acceptance testing of commercial shipments of zippers because the test method is used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.  
5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2058, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. T...
SCOPE
1.1 This test method covers the determination of the resistance of all types of zippers to corrosion and their ability to function properly after exposure of specified duration in a prescribed salt spray.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2054-99(2022)(Test Method)
Standard Test Method for Colorfastness of Zipper Tapes to Crocking

SIGNIFICANCE AND USE
5.1 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.  
5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the determination of the degree of color that may be transferred from the textile tape of zippers of all fibers to other surfaces by rubbing under wet or dry conditions, or both.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off