ASTM D2884-93(2012)
(Test Method)Standard Test Method for Yield Stress of Heterogeneous Propellants by Cone Penetration Method (Withdrawn 2017)
Standard Test Method for Yield Stress of Heterogeneous Propellants by Cone Penetration Method (Withdrawn 2017)
SIGNIFICANCE AND USE
The yield stress is a measure of the forces required to initiate and maintain flow from a storage vessel. If all the factors are constant, the propellant with the lower yield stress can be removed more completely from the vessel.
SCOPE
1.1 This test method covers determination of the yield stress of heterogeneous propellants, both of the gel and emulsion types, containing from 0 to 70 % solid additives.
1.2 The values stated in SI units are to be regarded as the standard. In cases where materials, products, or equipment are available in inch-pound units only, SI units are omitted.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This test method covered determination of the yield stress of heterogeneous propellants, both of the gel and emulsion types, containing from 0 % to 70 % solid additives.
Formerly under the jurisdiction of Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants, this test method was withdrawn in December 2017. This standard is being withdrawn without replacement due to its limited use by industry.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2884 − 93 (Reapproved 2012)
Standard Test Method for
Yield Stress of Heterogeneous Propellants by Cone
Penetration Method
This standard is issued under the fixed designation D2884; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.2 unworked penetration, n—the penetration at 298 K
2,3 (77°F) of a sample of the propellant which has received only
1.1 This test method covers determination of the yield
the minimum disturbance in transfer from the sample can to a
stress of heterogeneous propellants, both of the gel and
grease worker cup or dimensionally equivalent container. This
emulsion types, containing from 0 to 70 % solid additives.
shall be 76.2 6 0.3 mm (3 6 0.01 in.) in inside diameter and
1.2 The values stated in SI units are to be regarded as the
63.56 1.6 mm (2.5 6 0.06 in.) deep, as shown in Fig. 1.
standard. In cases where materials, products, or equipment are
3.1.2.1 Discussion—The conversion of penetration to yield
available in inch-pound units only, SI units are omitted.
stresshasnotbeencorrectedforthedisplacementofthesample
1.3 This standard does not purport to address all of the
by the submerged portion of the cone. For this reason cup
safety concerns, if any, associated with its use. It is the diameter is critical, and any deviation from 76.2 6 0.3 mm (3
responsibility of the user of this standard to establish appro-
6 0.01 in.) must be reported as a nonstandard condition.
priate safety and health practices and determine the applica-
3.1.3 yield stress—the maximum shear stress that can be
bility of regulatory limitations prior to use.
applied without causing permanent deformation (seeTerminol-
ogy D2507). Specifically in this test method, it is the weight of
2. Referenced Documents
the 30-g mass cone-test rod assembly in dynes, corrected for
buoyancy, divided by the calculated wetted area of the cone
2.1 ASTM Standards:
D2507 Terminology of Rheological Properties of Gelled (that is, the area of the cone in contact with the propellant after
the 5-s drop period).
Rocket Propellants (Withdrawn 2003)
4. Summary of Test Method
3. Terminology
4.1 The penetration is determined at 298 K (77°F) by
3.1 Definitions of Terms Specific to This Standard:
releasingthecone-testrodassemblyfromthepenetrometerand
3.1.1 penetration of a propellant, n—The depth, in tenths of
allowing the assembly to drop for 5 s. The cone will be
a millimetre that a standard cone penetrates the sample under
essentially at rest in less than this time, so that exact timing is
prescribed conditions of weight, time, and temperature.
not critical.
5. Significance and Use
5.1 The yield stress is a measure of the forces required to
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
initiate and maintain flow from a storage vessel. If all the
Subcommittee D02.L0.07 on Engineering Sciences of High Performance Fluids and
factors are constant, the propellant with the lower yield stress
Solids (Formally D02.1100).
can be removed more completely from the vessel.
Current edition approved April 15, 2012. Published April 2012. Originally
approved in 1970. Last previous edition approved in 2007 as D2884–93(2007).
6. Apparatus
DOI: 10.1520/D2884-93R12.
This test method is identical in substance with the JANNAF method, “Hetero-
6.1 Penetrometer, to measure the penetration of the standard
geneous Propellant Characterization, Part III, Procedure for Measuring Yield Stress
cone in the propellant. The cone assembly or the table of the
of Heterogeneous Propellants,” published by the Chemical Propulsion Information
Agency, July 1969, Johns Hopkins University, Applied Physics Laboratory, Johns
penetrometer shall be adjustable to enable accurate placement
Hopkins Rd., Laurel, MD 20810.
of the cone on the level surface of the propellant while
ASTM Committee F07 on Aerospace and Aircraft maintains a continued
maintaining a zero reading on the indicator. The cone should
interest in this test method and will make use of it in the future.
fall, when released, without appreciable friction for at least
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
42.0mmbutnotmorethan60.0mmsotheconewillnothitthe
Standards volume information, refer to the standard’s Document Summary page on
bottom of the container. The instrument shall be provided with
the ASTM website.
leveling screws to maintain the cone shaft in a vertical position
The last approved version of this historical standard is referenced on
www.astm.org. and a spirit level to determine the attitude of the instrument.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D2884 − 93 (2012)
motion at an angle of 45° across the rim of the cup. Do not
perform any further leveling or smoothing of the surface
throughout the determination of unworked penetration, and
determine the measurement immediately.
7.3 Cleaning Cone and Shaft—Clean the penetrometer cone
carefully before each test. Bending of the test rod can be
avoided by holding it securely in its raised position while
cleaning. Do not permit grease, oil, or propellant on the test
rod, as they can cause drag on the assembly. Do not rotate the
cone, as this may cause wear on the aluminum test rod.
7.4 Penetration Measurement:
NOTE 1—This cup is dimensionally equivalent to the grease worker
7.4.1 Place the cup on the penetrometer table, making
cup.
certain that it cannot teeter. Set the mechanisms to hold the
FIG. 1 Penetrometer Cup
cone in the zero position, and adjust the apparatus carefully so
that the tip of the cone just touches the surface at the center of
6.1.1 A 15-g test rod shall be substituted for the regular
the test sample. Watching the shadow of the cone tip is an aid
47.5-g rod in accordance with the manufacturer’s instructions.
to accurate setting. Release the test rod rapidly, and allow it to
6.2 Cone, of the dimensions shown in Fig. 2. drop for 5.0 6 0.5 s. The clutch jaws must not drag on the
shaft. Gently depress the depth gage rod until stopped by the
NOTE 1—Some cones have correct dimensions and weight (15.0 g) but
lower stop, and read the penetration from the indicator.
react with hydrazine gels.The user should plan to have one made to order.
7.4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.