iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM A1017/A1017M-07

(Specification)

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten

Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten

ABSTRACT
This specification covers chromium-molybdenum-tungsten alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service. The plates shall be available in three grades, namely Grades 23, 911, and 122, having different alloy contents. The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical requirements. The steel shall be killed and the plates shall undergo heat treatment. In order to determine mechanical properties such as yield strength and elongation, the plates shall be subjected to tension and hardness tests.
SCOPE
1.1 This specification covers Chromium-Molybdenum-Tungsten alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service.
1.2 Plates are available under this specification in three grades having different alloy contents as follows:
1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.
1.4 The specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

General Information

Status
Historical
Publication Date
28-Feb-2007
ICS
77.140.30 - Steels for pressure purposes
Technical Committee
A01 - Steel, Stainless Steel and Related Alloys
Drafting Committee
A01.11 - Steel Plates for Boilers and Pressure Vessels
Current Stage
Ref Project

Relations

Replaces
ASTM A1017/A1017M-06 - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten
Effective Date
01-Mar-2007
Replaced By
ASTM A1017/A1017M-11 - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten
Effective Date
01-Apr-2011
Referred By
ASTM A387/A387M-17a - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum
Effective Date
01-Mar-2007
Referred By
ASTM A20/A20M-20 - Standard Specification for General Requirements for Steel Plates for Pressure Vessels
Effective Date
01-Mar-2007

Buy Standard

ASTM A1017/A1017M-07 - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-TungstenASTM A1017/A1017M-07 - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten
PreviousNext
Technical specification
ASTM A1017/A1017M-07 - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A1017/A1017M – 07
Standard Specification for
Pressure Vessel Plates, Alloy Steel, Chromium-
1
Molybdenum-Tungsten
This standard is issued under the fixed designation A1017/A1017M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* A435/A435M Specification for Straight-Beam Ultrasonic
Examination of Steel Plates
1.1 This specification covers Chromium-Molybdenum-
A577/A577M Specification for UltrasonicAngle-Beam Ex-
Tungsten alloy steel plates intended primarily for welded
amination of Steel Plates
boilers and pressure vessels designed for elevated temperature
service.
3. General Requirements
1.2 Plates are available under this specification in three
3.1 Material supplied to this material specification shall
grades having different alloy contents as follows:
conform to Specification A20/A20M. Such requirements out-
Nominal Nominal Nominal
line the testing and retesting methods and procedures, permis-
Chromium Molybdenum Tungsten
Grade Content, % Content, % Content, %
sible variations in dimensions and weight [mass], quality and
repair of defects, marking, loading, and so forth.
23 2.25 0.20 1.60
3.2 Specification A20/A20M also establishes the rules for
911 9.00 1.00 1.00
122 12.00 0.40 2.00
the ordering information that should be complied with when
purchasing material to this specification.
1.3 The maximum thickness of plates is limited only by the
3.3 In addition to the basic requirements of this specifica-
capacity of the composition to meet the specified mechanical
tion, certain supplementary requirements are available when
property requirements.
additional control, testing, or examination is required to meet
1.4 The specification is expressed in both inch-pound units
end use requirements. The purchaser is referred to the listed
and in SI units. However, unless the order specifies the
supplementary requirements in this specification and to the
applicable “M” specification designation (SI units), the mate-
detailed requirements in Specification A20/A20M.
rial shall be furnished to inch-pound units.
3.4 If the requirements of this specification are in conflict
1.5 The values stated in either inch-pound units or SI units
with the requirements of SpecificationA20/A20M, the require-
are to be regarded separately as standard. Within the text, the
ments of this specification shall prevail.
SI units are shown in brackets. The values stated in each
system are not exact equivalents; therefore, each system must
4. Materials and Manufacture
be used independently of the other.
4.1 Steelmaking Practice—The steel shall be killed.
2. Referenced Documents
5. Heat Treatment
2
2.1 ASTM Standards:
5.1 Except as allowed by 5.2 and 5.3, all plates shall be
A20/A20M Specification for General Requirements for
normalized at 1900 to 1975°F [1040 to 1080°C]. Plates for
Steel Plates for Pressure Vessels
Grades 23 and 122 shall be tempered at 1350 to 1470°F [730
to 800°C]. Grade 911 plates shall be tempered at 1365 to
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
1435°F [740 to 780°C].
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
5.2 If permitted by the purchaser, plates for Grades 23 and
A01.11 on Steel Plates for Boilers and Pressure Vessels.
122 may be austenitized at 1900 to 1975°F [1040 to 1080°C],
Current edition approved March 1, 2007. Published March 2007. Originally
approved in 2001. Last previous edition approved in 2006 asA1017/A1017M – 06.
subjected to accelerated cooling from the austenitizing tem-
DOI: 10.1520/A1017_A1017M-07.
perature by air blasting or liquid quenching, and then tempered
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
at 1350 to 1470°F [730 to 800°C].
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A1017/A1017M – 07
TABLE 1 Chemical Requirements TABLE 2 Tensile Requirements
Grade 23 Grade 911 Grade 122
NOTE—Where“.” appears in this table there is no requirement.
Tensile Strength, ksi [MPa] 74 to 100 90 to 120
Element Composition %
[510 to 690] [620 to 840] 90 [620] min.
Grade 23 Grade 911 Grade 122
Yield Strength ksi [MPa] min 58 [400] 64 [440] 58 [400]
Carbon
Elongation in 2 in. % min 20 18 20
Heat Analysis 0.04–0.10 0.09–0.13 0.07–0.14
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM A455/A455M-12a(2023)(Specification)
Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese

ABSTRACT
This specification covers high-tensile strength carbon-manganese steel plates intended for welded pressure vessels. Plates are normally supplied in the as-rolled condition. The plates may be ordered normalized or stress relieved, or both. The steel shall conform to the chemical composition requirements. The plates, as represented by the tension test specimens, shall conform to the mechanical property requirements.
SCOPE
1.1 This specification2 covers high-tensile strength carbon-manganese steel plates intended for welded pressure vessels.  
1.2 This steel is usually made to a semi-killed or capped deoxidation practice; however, at the purchaser's or the steel producer's option, the steel may be made silicon-killed or aluminum-killed.  
1.3 The maximum thickness of plates furnished under this specification shall be 3/4 in. [20 mm].  
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.  
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A724/A724M-09(2023)(Specification)
Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels

ABSTRACT
This specification covers standard requirements for three grades of carbon-manganese-silicon steel, designated Grades A, B, and C. Grade C may be produced with a boron addition. The plates shall be quenched and tempered and shall be intended for welded-layered pressure vessels. The steel shall be killed and shall conform to the fine austenitic grain size requirement. Heat and product analyses shall be performed wherein the material shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum, vanadium, and boron. The steel plate shall undergo tension test and shall conform to tensile requirements such as tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification2 covers three grades of carbon-manganese-silicon steel, designated Grades A, B, and C. Grade C may be produced with a boron addition. The plates are quenched and tempered and are intended for welded-layered pressure vessels.  
1.2 The maximum thickness of plates supplied under this specification is limited only by the capability of the chemical composition to meet the specified mechanical requirements. However, current practice normally limits the maximum thickness to 7/8 in. [22 mm] for Grades A and B, and to 2 in. [50 mm] for Grade C.  
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A517/A517M-17(2023)(Specification)
Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered

ABSTRACT
This specification covers standard requirements for high-strength quenched and tempered alloy steel plates intended for use in fusion welded boilers and other pressure vessels. The steel shall be killed and shall conform to the fine austenitic grain size requirement. Heat and product analyses shall be conducted wherein the material shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, boron, vanadium, titanium, zirconium, copper, and columbium. Tensile properties of the steel plate shall meet the specified values for tensile strength, yield strength, and elongation. The material shall undergo mechanical tests such as tension test and transverse Charpy V-notch impact test.
SCOPE
1.1 This specification2 covers high-strength quenched and tempered alloy steel plates intended for use in fusion welded boilers and other pressure vessels.  
1.2 This specification includes a number of grades as manufactured by different producers, but all having the same mechanical properties and general characteristics.  
1.3 The maximum thickness of plates furnished under this specification shall be as follows:    
Grade  
Thickness  
A, B  
1.25 in. [32 mm]  
H, S  
2 in. [50 mm]  
P  
4 in. [100 mm]    
F  
2.50 in. [65 mm]    
E, Q  
6 in. [150 mm]  
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other without combining values in any way.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A859/A859M-23(Specification)
Standard Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components

ABSTRACT
This specification covers the standard requirements for low-carbon age-hardened nickel-copper-chromium-molybdenum-columbium alloy steel forgings for pressure vessel components. Materials shall be manufactured to a killed fine austenitic grain size, by vacuum degas melting process. Heat treatment shall be conducted, according to class, by: normalizing and precipitation hardening (Grade A, Class 1); liquid quenching and precipitation hardening (Grade A, Class 2); or double liquid-quenching, tempering, double austenitizing, and precipitation hardening (Grade B). Heat and product analyses shall be used to evaluate the conformance of forgings to required chemical compositions. Tensile, notch toughness, and Charpy impact requirements shall be examined, for which one of four sampling methods may be employed. One tension test and one impact test (for three samples) shall be made for each forging. Dimensions and finishes of the forgings shall conform to that specified by the purchaser. Repair welding shall also be performed only if permitted by the purchaser.
SCOPE
1.1 This specification covers requirements for low-carbon age-hardening nickel-copper-chromium-molybdenum-columbium alloy steel forgings for pressure vessel components.  
1.2 Forgings under this specification are available as Grades A or B. Grade A may be ordered in one or two classes as follows:  
1.2.1 Grade A Class 1—Normalized-and-precipitation-heat-treated, providing a minimum yield strength of 55 ksi [380 MPa] and a minimum tensile strength of 65 ksi [450 MPa].  
1.2.2 Grade A Class 2—Quenched-and-precipitation-heat-treated, providing a minimum yield strength of 65 ksi [450 MPa] and a minimum tensile strength of 75 ksi [515 MPa].  
1.2.3 Grade A was the original steel composition in this specification.  
1.3 Although the material is readily weldable, welding procedures are of fundamental importance and must be such as not to affect adversely the properties of the material, especially in the heat-affected zone. It is presupposed that welding procedures will be suitable for the material being welded.  
1.4 Supplementary requirements, including those applicable in Specification A788/A788M, are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined.  
1.6 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM A240/A240M-23a(Specification)
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ABSTRACT
This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. The steel shall conform to the requirements as to chemical composition specified. The material shall conform to the mechanical properties specified.
SCOPE
1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM A508/A508M-23a(Specification)
Standard Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels

ABSTRACT
This specification covers quenched and tempered vacuum-treated carbon and alloy steel forgings for pressure vessels, such as those used in reactor systems, specifically, vessel closures, shells, flanges, tube sheets, rings, heads, and similar parts. Steels shall be manufactured by basic electric-furnace process except when secondary ladle refining or remelting process is employed, and shall be vacuum treated prior to or during the pouring of the ingot. Materials shall also go through preliminary heat treatment and quenching for mechanical properties. Heat and product analyses shall be executed to evaluate the conformance of the forgings with specified chemical requirements. Tension and Charpy impact tests shall also be performed to examine the conformance of steel specimens with the following mechanical properties: tensile strength, yield strength, elongation, and reduction of area. Nondestructive inspection procedures, such as magnetic particle examination, and longitudinal wave and angle beam ultrasonic examination, shall also be carried out. Repair welding may be permitted at the option of the purchaser.
SCOPE
1.1 This specification2 covers quenched and tempered vacuum-treated carbon and alloy steel forgings for pressure vessels such as those used in reactor systems. Specifically, it covers forgings for vessel closures, shells, flanges, tube sheets, rings, heads, and similar parts.  
1.2 All grades are considered weldable under proper conditions. Welding technique is of fundamental importance, and it is presupposed that welding procedure and inspection will be in accordance with approved methods for the grade of material used.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.
Note 1: Grades 1 and 1A are composed of different chemistries but have the same mechanical requirements.
Note 2: Designations have been changed as follows:    
Current  
Formerly  
Grade 1  
Class 1  
Grade 1A  
Class 1A  
Grade 2 Class 1  
Class 2  
Grade 2 Class 2  
Class 2A  
Grade 3 Class 1  
Class 3  
Grade 3 Class 2  
Class 3A  
Grade 4N Class 1  
Class 4  
Grade 4N Class 2  
Class 4A  
Grade 4N Class 3  
Class 4B  
Grade 5 Class 1  
Class 5  
Grade 5 Class 2  
Class 5A  
Grade 22 Class 3  
Class 22B  
Grade 22 Classes 4, 5, 6, and 7  
Grade 3V  
Class 3V  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM A414/A414M-23(Specification)
Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels

ABSTRACT
This specification covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Tensile and yield strengths shall be determined after a tension test of the sheets. The material shall be furnished without removing the hot-rolled oxide or scale. When required, the material may be specified to be pickled or blast cleaned. When specified to be pickled or blast cleaned, the material shall be furnished oiled. When required, pickled or blast-cleaned material may be specified to be furnished dry.
SCOPE
1.1 This specification2 covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Welding and brazing technique is of fundamental importance and shall be in accordance with commercial practices.  
1.2 The following grades are included in this specification:    
Mechanical Requirements  
Yield Strength, min  
Tensile Strength, min  
Grade  
ksi  
MPa  
ksi  
MPa  
A  
25  
170  
45  
310  
B  
30  
205  
50  
345  
C  
33  
230  
55  
380  
D  
35  
240  
60  
415  
E  
38  
260  
65  
450  
F  
42  
290  
70  
485  
G  
45  
310  
75  
515  
H  
45  
310  
75  
515  
1.3 Hot-rolled carbon steel sheet is generally furnished in cut lengths and to decimal thickness only. Coils may be furnished, provided tension test specimens are taken to represent the middle of the slab as required by 6.1.3. The purchaser should recognize this may require cutting the coils to obtain test samples and results in half-size coils. The sheet is furnished to the following size limits:    
Width, in. [mm]    
Thickness, in. [mm]  
Over 12 [Over 300]    
0.270 to 0.230 [7.0 to 6.0]  
sheet (coils only)  
Under 0.230 to 0.057 [6.0 to 1.5]  
sheet  
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.  
1.5 Tolerances are found in General Requirements Specifications A568/A568M and A635/A635M. The appropriate General Requirements specification is applied based on the thickness and width of the product ordered.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM A387/A387M-17a(2023)(Specification)
Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum

ABSTRACT
This specification covers chromium-molybdenum alloy steel plates for welded broilers and pressure vessels designed for elevated temperature service. Materials considered under this specification are available in grades 2, 12, 11, 22, 22L, 21, 21L, 5, 9 and 91. The steel materials shall be killed and shall be thermally treated. The steel specimens shall undergo heat analysis and product analysis and shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, nickel, vanadium, columbium, boron, nitrogen, aluminum, titanium, and zirconium. The steel specimens shall also undergo tension tests and shall conform to the required values of tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification2 covers chromium-molybdenum alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service.  
1.2 Plates are available under this specification in several grades having different alloy contents as follows:    
Nominal  
Nominal  
Chromium  
Molybdenum  
Grade  
Content, %  
Content, %  
2  
0.50  
0.50  
12  
1.00  
0.50  
11  
1.25  
0.50  
22  
2.25  
1.00  
21  
3.00  
1.00  
5  
5.00  
0.50  
9  
9.00  
1.00  
91  
9.00  
1.00  
1.3 Each grade except Grade 91 is available in two classes of tensile strength levels as defined in the Tensile Requirements tables. Grade 91 is available only as Class 2. Grade 91 consists of two types, with Type 2 differentiated from Type 1 by requiring restricted composition for the enhancement of creep resistance.
Note 1: Grade 911, previously covered by this specification, is now covered by Specification A1017/A1017M.  
1.4 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.  
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM A203/A203M-23(Specification)
Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel

ABSTRACT
This specification covers nickel-alloy steel plates intended primarily for welded pressure vessels. As a steel making practice, the steel shall be killed and shall conform to fine grain size requirements. The heat treatment requirements for all plates are presented, and all plates under Grades A, B, D, and E shall be normalized as required. The steel shall conform to the required chemical compositions. Two mechanical test requirements are presented that includes, tension test requirements and impact test requirements.
SCOPE
1.1 This specification2 covers nickel-alloy steel plates intended primarily for welded pressure vessels.  
1.2 Plates under this specification are available with four strength levels and two nickel compositions as follows:    
Grade  
Nominal Nickel
Content %  
Yield Strength, min, ksi [MPa]  
Tensile Strength, min, ksi [MPa]  
A  
2.25  
37 [255]  
65 [450]  
B  
2.25  
40 [275]  
70 [485]  
D  
3.50  
37 [255]  
65 [450]  
E  
3.50  
40 [275]  
70 [485]  
F  
3.50  
2 in. [50 mm] and under  
55 [380]  
80 [550]  
Over 2 in. [50 mm]  
50 [345]  
75 [515]  
1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.  
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A479/A479M-23a(Specification)
Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

ABSTRACT
This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction. Four grades of the stainless steel are available which includes austenitic, austenitic-ferritic, ferritic, and martensitic grades. Mechanical properties such as tensile strength, yield strength, elongation, and hardness shall be determined for the specimens subjected to normalized, tempered, annealed, and quenched conditions. The austenitic stainless steels shall be subjected to heat treatment and shall undergo corrosion test.
SCOPE
1.1 This specification2 covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.2
Note 1: There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off