ASTM F467M-01

Standard Specification for Nonferrous Nuts for General Use [Metric]

SCOPE
1.1 This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications.  
1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468M.
Note 1—This specification is the metric companion of Specification F467.

General Information

• Status: Historical
• Publication Date: 09-Oct-2001
• ICS: 21.060.20 - Nuts
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.04 - Nonferrous Fasteners

Relations

• Replaces: ASTM F467M-98 - Standard Specification for Nonferrous Nuts for General Use [Metric]
• Effective Date: 10-Oct-2001
• Replaced By: ASTM F467M-01a - Standard Specification for Nonferrous Nuts for General Use [Metric]
• Effective Date: 10-Oct-2001
• Referred By: ASTM F468M-06(2018) - Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
• Effective Date: 10-Oct-2001
• Referred By: ASTM B745/B745M-15(2021) - Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
• Effective Date: 10-Oct-2001
• Referred By: ASTM B746/B746M-22 - Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
• Effective Date: 10-Oct-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: F 467M – 01
METRIC
Standard Specification for
1
Nonferrous Nuts for General Use [Metric]
This standard is issued under the fixed designation F 467M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope E 62 Test Methods for Chemical Analysis of Copper and
6
Copper Alloys (Photometric Methods)
1.1 This specification covers the requirements for commer-
E 75 Test Methods for Chemical Analysis of Copper-Nickel
cial wrought nonferrous nuts in nominal thread diameters M6
6
and Copper-Nickel-Zinc Alloys
to M36 inclusive in a number of alloys in common use and
E 76 Test Methods for Chemical Analysis of Nickel–Cop-
intended for general service applications.
6
per Alloys
1.2 Applicable bolts, cap screws, and studs for use with nuts
E 92 Test Method for Vickers Hardness of Metallic Mate-
covered by this specification are covered by Specification
4
rials
F 468M.
E 101 Test Method for Spectrographic Analysis of Alu-
NOTE 1—This specification is the metric companion of Specification
minum and Aluminum Alloys by the Point-to-Plane Tech-
F 467.
8
nique
E 120 Test Methods for Chemical Analysis of Titanium and
2. Referenced Documents
6
Titanium Alloys
2.1 ASTM Standards:
9
E 165 Practice for Liquid Penetrant Inspection Method
B 154 Test Method for Mercurous Nitrate Test for Copper
E 227 Test Method for Optical Emission Spectrometric
2
and Copper Alloys
Analysis of Aluminum and Aluminum Alloys by the
3
D 3951 Practice for Commercial Packaging
6
Point-to-Plane Technique
E 18 Test Methods for Rockwell Hardness and Rockwell
E 354 Test Methods for Chemical Analysis of High-
4
Superficial Hardness of Metallic Materials
Temperature, Electrical, Magnetic, and Other Similar Iron,
E 29 Practice for Using Significant Digits in Test Data to
6
Nickel, and Cobalt Alloys
5
Determine Conformance with Specifications
E 478 Test Methods for Chemical Analysis of Copper
E 34 Test Methods for Chemical Analysis of Aluminum and
6
Alloys
6
Aluminum Base Alloys
E 1409 Test Method for Determination of Oxygen in Tita-
E 38 Methods for Chemical Analysis of Nickel-Chromium
nium and Titanium Alloys by the Inert Gas Fusion Tech-
7
and Nickel-Chromium-Iron Alloys
6
nique
6
E 53 Test Methods for Chemical Analysis of Copper
F 468M Specification for Nonferrous Bolts, Hex Cap
E 54 Test Methods for Chemical Analysis of Special
10
Screws, and Studs for General Use [Metric]
6
Brasses and Bronzes
F 606M Test Methods for Determining the Mechanical
E 55 Practice for Sampling Wrought Nonferrous Metals and
Properties of Externally and Internally Threaded Fasteners,
6
Alloys for Determination of Chemical Composition
10
Washers, and Rivets [Metric]
F 1470 Guide for Fastener Sampling for Specified Mechani-
1
10
This specification is under the jurisdiction of ASTM Committee F16 on
cal Properties and Performance Inspection
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous
2.2 ANSI Standards:
Fasteners.
Current edition approved Apr. 10, 2001. Published June 2001. Originally
published as F 467M – 79. Last previous edition F 467M – 98.
2
Annual Book of ASTM Standards, Vol 02.01.
3
Annual Book of ASTM Standards, Vol 15.09.
4
Annual Book of ASTM Standards, Vol 03.01.
5 8
Annual Book of ASTM Standards, Vol 14.02. Discontinued; see 1995 Annual Book of ASTM Standards, Vol 03.05.
6 9
Annual Book of ASTM Standards, Vol 03.05. Annual Book of ASTM Standards, Vol 03.03.
7 10
Discontinued 1989; Replaced by E 350. Annual Book of ASTM Standards, Vol 01.08.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 467M
11
B 1.13M Metric Screw Threads material at the option of the manufacturer.
11
B 18.2.4.1MMetric Hex Nuts, Style 1 4.2.2 Condition—Except as provided in 4.2.3, the nuts shall
be furnished in the condition specified below:
3. Ordering Information
Alloy Condition
3.1 Orders for nuts under this specification shall include the Copper (all alloys) As formed or stress relieved at manufacturer’s option
Nickel alloys 400 and As formed or stress relieved at manufacturer’s option
following information:
405
3.1.1 Quantity (numbers of pieces of each item and size),
Nickel alloy 500 Solution annealed and aged
3.1.2 Name of item, Aluminum alloys:
2024-T4 Solution treated and naturally aged
3.1.3 Nominal thread diameter and thread pitch,
6061-T6 Solution treated and artificially aged
3.1.4 Alloy number (Table 1),
6262-T9 Solution treated, artificia
...