ASTM F2753-10(2015)
(Practice)Standard Practice to Evaluate the Effect of Dynamic Rolling Load over Resilient Floor Covering System
Standard Practice to Evaluate the Effect of Dynamic Rolling Load over Resilient Floor Covering System
SIGNIFICANCE AND USE
4.1 The effect of dynamic rolling load over resilient floor covering system is important since the resistance reflects the ability of a resilient floor covering system to properly perform under specific use or condition.
4.2 Excessive rolling load over an installed resilient floor covering may cause floor covering system failures such as bond failure, delamination, and finish or coating deteriorations.
4.3 The effect of dynamic rolling load shall be measured by qualitative evaluation comparing the tested assembly with a standard assembly.
SCOPE
1.1 This practice covers the determination of the effect of dynamic rolling load over a resilient floor covering.
1.2 This practice is intended to be used by resilient, adhesive and underlayment manufacturers to measure the impact of a dynamic rolling load over a specific product or a combination of products.
1.3 This practice may be used to evaluate the performance of joints (sealed or welded) in the resilient floor covering.
1.4 This practice may be used to aid in the diagnosis of a specific assembly performance and provide comparative evaluation.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2753 − 10 (Reapproved 2015)
Standard Practice to
Evaluate the Effect of Dynamic Rolling Load over Resilient
Floor Covering System
This standard is issued under the fixed designation F2753; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4. Significance and Use
1.1 This practice covers the determination of the effect of
4.1 The effect of dynamic rolling load over resilient floor
dynamic rolling load over a resilient floor covering.
covering system is important since the resistance reflects the
ability of a resilient floor covering system to properly perform
1.2 This practice is intended to be used by resilient, adhe-
under specific use or condition.
sive and underlayment manufacturers to measure the impact of
a dynamic rolling load over a specific product or a combination
4.2 Excessive rolling load over an installed resilient floor
of products.
covering may cause floor covering system failures such as
bond failure, delamination, and finish or coating deteriorations.
1.3 This practice may be used to evaluate the performance
of joints (sealed or welded) in the resilient floor covering.
4.3 The effect of dynamic rolling load shall be measured by
qualitative evaluation comparing the tested assembly with a
1.4 This practice may be used to aid in the diagnosis of a
standard assembly.
specific assembly performance and provide comparative evalu-
ation.
5. Apparatus
1.5 The values stated in inch-pound units are to be regarded
5.1 Rolling load simulator comparable or similar to the
as standard. The values given in parentheses are mathematical
apparatus as described in Annex A1.
conversions to SI units that are provided for information only
and are not considered standard.
6. Procedure
1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 6.1 Test Assembly:
responsibility of the user of this standard to establish appro- 6.1.1 The test assembly shall have a minimum size of 12 in.
priate safety and health practices and determine the applica-
(30.5 cm) by 24 in. (61.0 cm).
bility of regulatory limitations prior to use.
6.1.2 The base substrate shall be rigid such as a concrete
slab 4 in. (10 cm), a cementitious board or a ⁄4 in. (1.9 cm)
2. Referenced Documents
plywood, panel type underlayments, (Practice F1482 provides
2.1 ASTM Standards: additional information), or others. Adhere the flooring test
specimen to the base substrate according to the manufacturer’s
F141 Terminology Relating to Resilient Floor Coverings
F1482 Practice for Installation and Preparation of Panel installation instructions.
Type Underlayments to Receive Resilient Flooring
6.2 Testing:
6.2.1 The test shall run at a temperature of 73 6 5°F (23
3. Terminology
63°C) and at 50 6 10 % relative humidity unless otherwise
3.1 Definitions used in this practice shall be in accordance
specified.
with Terminology F141.
6.2.2 Install the wheel to be tested.
6.2.3 After proper conditioning, the test assembly should be
installed and fixed with clamps on the table. The assembly
This practice is under the jurisdiction of ASTM Committee F06 on Resilient
Floor Coverings and is the direct responsibility of Subcommittee F06.40 on
must not move.
Practices.
6.2.4 Select the wheel path and the number of cycles.
CurrenteditionapprovedMay1,2015.PublishedJuly2015.Originallyapproved
Usually a series of 500 cycles is used.
in 2010. Last previous edition approved in 2010 as F2573-10. DOI. 10.1520/
F2753–10R15.
6.2.5 Place the required amount of auxiliary weights. A
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
starting weight of 100 lb (45.4 kg) is generally used t
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2753 − 10 F2753 − 10 (Reapproved 2015)
Standard Practice to
Evaluate the Effect of Dynamic Rolling Load over Resilient
Floor Covering System
This standard is issued under the fixed designation F2753; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice covers the determination of the effect of dynamic rolling load over a resilient floor covering.
1.2 This practice is intended to be used by resilient, adhesive and underlayment manufacturers to measure the impact of a
dynamic rolling load over a specific product or a combination of products.
1.3 This practice may be used to evaluate the performance of joints (sealed or welded) in the resilient floor covering.
1.4 This practice may be used to aid in the diagnosis of a specific assembly performance and provide comparative evaluation.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
F141 Terminology Relating to Resilient Floor Coverings
F1482 Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
3. Terminology
3.1 Definitions used in this practice shall be in accordance with Terminology F141.
4. Significance and Use
4.1 The effect of dynamic rolling load over resilient floor covering system is important since the resistance reflects the ability
of a resilient floor covering system to properly perform under specific use or condition.
4.2 Excessive rolling load over an installed resilient floor covering may cause floor covering system failures such as bond
failure, delamination, and finish or coating deteriorations.
4.3 The effect of dynamic rolling load shall be measured by qualitative evaluation comparing the tested assembly with a
standard assembly.
5. Apparatus
5.1 Rolling load simulator comparable or similar to the apparatus as described in Annex A1.
6. Procedure
6.1 Test Assembly:
6.1.1 The test assembly shall have a minimum size of 12 in. (30.5 cm) by 24 in. (61.0 cm).
This practice is under the jurisdiction of ASTM Committee F06 on Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.40 on Practices.
Current edition approved June 1, 2010May 1, 2015. Published August 2010July 2015. DOI. 10.1520/F2753–10.Originally approved in 2010. Last previous edition
approved in 2010 as F2573-10. DOI. 10.1520/F2753–10R15.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F2753 − 10 (2015)
6.1.2 The base substrate shall be rigid such as a concrete slab 4 in. (10 cm), a cementitious board or a ⁄4 in. (1.9 cm) plywood,
panel type underlayments, (Practice F1482 provides additional information), or others. Adhere the flooring test specimen to the
base substrate according to the manufacturer’s installation instructions.
6.2 Testing:
6.2.1 The test
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.