iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM A922-05(2010)

(Specification)

Standard Specification for Silicon Metal

Standard Specification for Silicon Metal

ABSTRACT
This specification covers different sizes of several grades of silicon metal. The metal shall undergo chemical analysis and shall conform to specified chemical composition requirements.
SCOPE
1.1 This specification covers several grades of silicon metal.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The SI equivalents of inch-pound units given may be approximate.

General Information

Status
Historical
Publication Date
31-Mar-2010
ICS
77.120.99 - Other non-ferrous metals and their alloys
Technical Committee
A01 - Steel, Stainless Steel and Related Alloys
Drafting Committee
A01.18 - Castings
Current Stage
Ref Project

Relations

Replaces
ASTM A922-05 - Standard Specification for Silicon Metal
Effective Date
01-Apr-2010
Replaced By
ASTM A922-05(2015) - Standard Specification for Silicon Metal
Effective Date
01-Nov-2015
Referred By
ASTM A1025/A1025M-10(2020) - Standard Specification for Ferroalloys and Other Alloying Materials, General Requirements
Effective Date
01-Apr-2010

Buy Standard

ASTM A922-05(2010) - Standard Specification for Silicon MetalASTM A922-05(2010) - Standard Specification for Silicon Metal
PreviousNext
Technical specification
ASTM A922-05(2010) - Standard Specification for Silicon Metal
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A922 −05(Reapproved 2010)
Standard Specification for
Silicon Metal
This standard is issued under the fixed designation A922; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope In case of conflict between the requirements of this specifica-
tion and Specification A1025, this specification shall prevail.
1.1 This specification covers several grades of silicon metal.
1.2 The values stated in inch-pound units are to be regarded
4. Chemical Composition
as standard. The values given in parentheses are mathematical
4.1 The grades shall conform to the requirements as to the
conversions to SI units that are provided for information only
chemical composition specified in Table 1.
and are not considered standard. The SI equivalents of inch-
pound units given may be approximate.
4.2 The manufacturer shall furnish an analysis of each
shipment showing the percentage of each element specified.
2. Referenced Documents
4.3 Upon request of the purchaser, the manufacturer shall
2.1 ASTM Standards:
furnish an analysis of any trace elements on a schedule
A1025 Specification for Ferroalloys and Other Alloying
mutually agreed upon between the supplier and the purchaser.
Materials, General Requirements
E11 Specification for Woven Wire Test Sieve Cloth and Test
5. Size
Sieves
5.1 The various grades are available in sizes listed in Table
E50 Practices for Apparatus, Reagents, and Safety Consid-
2.
erations for Chemical Analysis of Metals, Ores, and
Related Materials
5.2 The sizes listed in Table 2 are typical as shipped from
E60 Practice for Analysis of Metals, Ores, and Related the manufacturer’s plant. The various grades can exhibit
Materials by Spectrophotometry
different degrees of friability; therefore some attrition may be
E360 Test Methods for Chemical Analysis of Silicon and expected in transit, storage, and handling.Aquantitative test is
Ferrosilicon (Withdrawn 2003)
not available for rating relative friability of silicon metal. A
code system has been developed, therefore, for this purpose,
3. General Conditions for Delivery
and a number rating for each product type is shown in Table 3.
Definitions applicable to these code numbers are given in
3.1 Materialsfurnishedtothisspecificationshallconformto
Specification A1025.
therequirementsofSpecificationA1025,includinganysupple-
mentary requirements that are indicated in the purchase order.
6. Chemical Analysis
Failure to comply with the general requirements of Specifica-
tion A1025 constitutes nonconformance with this specification.
6.1 The chemical analysis of the material shall be made in
accordance with the procedure for silicon metal as described in
Test Methods E360 or alternative methods that will yield
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
equivalent results.
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.18 on Castings.
6.2 If alternative methods of analysis are used, in case of
Current edition approved April 1, 2010. Published May 2010. Originally
discrepancy, Test Methods E360 shall be used for referee.
approved in 1993. Last previous edition approved in 2005 as A922-05. DOI:
10.1520/A0922-05R10.
6.3 Where a method is not given in Test Methods E360 for
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM A495-06(2020)(Specification)
Standard Specification for Calcium-Silicon Alloys

ABSTRACT
This specification covers a standard grade of calcium-silicon, a standard grade of calcium-manganese-silicon, a standard grade of calcium-silicon-barium and a standard grade of ferro-calcium-silicon. The material shall conform to the requirements as to chemical composition specified.
SCOPE
1.1 This specification covers a standard grade of calcium-silicon, a standard grade of calcium-manganese-silicon, a standard grade of calcium-silicon-barium, and a standard grade of ferro-calcium-silicon.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A922-05(2020)(Specification)
Standard Specification for Silicon Metal

ABSTRACT
This specification covers different sizes of several grades of silicon metal. The metal shall undergo chemical analysis and shall conform to specified chemical composition requirements.
SCOPE
1.1 This specification covers several grades of silicon metal.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The SI equivalents of inch-pound units given may be approximate.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A144-04(2019)(Specification)
Standard Specification for Ferrotungsten

ABSTRACT
This guide covers standard specification for several grades of ferrotungsten. The material shall conform to the required chemical composition for tungsten, carbon, phosphorus, sulfur, silicon, molybdenum, and aluminum. The material shall also conform to supplementary chemical requirements for manganese, copper, nickel, arsenic, antimony, tin, and bismuth. Various grades of steel shall be available in specified sizes that meet the required size tolerance.
SCOPE
1.1 This specification covers four grades of ferrotungsten.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B277-18(2024)(Test Method)
Standard Test Method for Hardness of Electrical Contact Materials

SIGNIFICANCE AND USE
3.1 The Rockwell hardness and Rockwell superficial tests are useful when the test specimens are sufficiently thick (in relation to the indentor load) to ensure that the results are not affected by the flow of metal on the surface of the anvil. On a solid piece the flow of metal on the under surface may be detected by a bulge or marking. On composite pieces where the contact materials are attached to backings of a different material, the thickness limitations imposed for a solid piece shall apply to the contact material portion of such composite pieces.
Note 1: As a matter of information, it may be stated that tests on fine silver showed that on annealed samples having a Rockwell 15T hardness of 27, the readings were not affected on thicknesses 1/16 in. (1.6 mm) or over. On thicknesses of 1/32 in. (0.8 mm) Rockwell 15T scale readings of 72 and higher were not affected.  
3.2 The microindentation hardness test is of questionable significance when the metallic phases in a material are so large that the indentation does not represent an accurate average hardness. Sintered contact materials usually contain segregates differing greatly in hardness from the matrix hardness and may destroy the validity of microindentation hardness readings.  
3.3 Other aspects of significance and use shall be as described in the particular ASTM test method used, as listed in Section 2.
SCOPE
1.1 This test method covers the determination of the hardness of metallic materials used for electrical contacts. Rockwell, Rockwell superficial, Brinell, and microindentation hardness tests are included, along with information on the limitations and use of these tests.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar will all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM B541-24(Specification)
Standard Specification for Gold Electrical Contact Alloy

ABSTRACT
This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts. The material shall be finished by cold working, annealing, turning, grinding, and age hardening. The materials shall conform to the specified chemical composition requirements. Tensile strength, elongation, and hardness shall be determined by tension and hardness tests. Chemical analysis shall be done by spectrochemical or wet analysis methods.
SCOPE
1.1 This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains to the test method portion only, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM E439-23(Test Method)
Standard Test Methods for Chemical Analysis of Beryllium

SIGNIFICANCE AND USE
4.1 These test methods for the chemical analysis of beryllium metal are primarily intended as referee methods to test such materials for compliance with compositional specifications. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory.
SCOPE
1.1 These test methods cover the chemical analysis of beryllium having chemical compositions within the following limits:    
Element  
Range, %  
Aluminum  
0.05 to 0.30  
Beryllium  
97.5 to 100    
Beryllium Oxide  
0.3 to 3    
Carbon  
0.05 to 0.30  
Copper  
0.005 to 0.10  
Chromium  
0.005 to 0.10  
Iron  
0.05 to 0.30  
Magnesium  
0.02 to 0.15  
Nickel  
0.005 to 0.10  
Silicon  
0.02 to 0.15  
1.2 The test methods in this standard are contained in the sections as follows.    
Sections  
Chromium by the Diphenylcarbazide Spectrophotometric Test Method
[0.004 % to 0.04 %]  
10 – 19  
Iron by the 1,10-Phenanthroline Spectrophotometric Test Method
[0.05 % to 0.25 %]  
20 – 29  
Manganese by the Periodate Spectrophotometric Test Method
[0.008 % to 0.04 %]  
30 – 39  
Nickel by the Dimethylglyoxime Spectrophotometric Test Method
[0.001 % to 0.04 %]  
40 – 49  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E3097-23(Test Method)
Standard Test Method for Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys

SIGNIFICANCE AND USE
5.1 Constant force thermal cycling tests determine the effect of stress on the transformation temperatures, recovered strain and residual strain of a shape memory alloy. The tests may be for one thermal cycle. A standard test method for force controlled repeated thermal cycling of shape memory alloys is currently under development.  
5.2 Measurement of the specimen's thermomechanical behavior closely parallels many shape memory applications and provides a result that is applicable to the function of the material.  
5.3 This test method may be used for, but is not limited to, wire, round tube, or strip samples. Thus it is able to provide an assessment of the product in its semi-finished form.  
5.4 This test method provides a simple method for determining transformation temperatures by heating and cooling specimens through their full thermal transformation under force.  
5.5 This test method can be used on trained and processed material in a semi-finished form to measure Two Way Shape Memory Effect by comparing the strain in the austenite state and martensite states with no minimal applied stress. The force is set to a minimum value not to exceed a corresponding stress of 7 MPa (in accordance Test Method F2516).  
5.6 This test method is useful for quality control, specification acceptance, and research.  
5.7 Transformation temperatures derived from this test method may not agree with those obtained by other test methods due to the effects of strain and stress on the transformation.  
5.8 Components such as springs or other semi-finished parts can be tested using this method as agreed upon by the customer and supplier. Units of stress and strain can be replaced with force and displacement.
SCOPE
1.1 This test method defines procedures for thermomechanical cycling of shape memory alloy (SMA) material and components under constant force. This method characterizes the transformation properties such as transformation temperatures, actuation strain and residual strain, when a SMA is thermally cycled through the phase transformation under a constant applied force. This test is done to provide data for the selection of SMA materials, quality control, design allowables and actuator design.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM B664-18(2023)(Specification)
Standard Specification for 80 % Silver-20 % Graphite Sliding Contact Material

ABSTRACT
This specification defines the criteria for composition and other requirements for sliding contact materials or brushes with a nominal composition by weight of 20% silver and 80% graphite. Materials shall adhere to specified requirements for chemical composition, density, shear strength, and microstructure. They shall also conform to typical values of Rockwell superficial hardness and specific resistance.
SCOPE
1.1 This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 80 %, by weight, with the balance being substantially graphite.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar will all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B717-23(Specification)
Standard Specification for Refined Ruthenium

ABSTRACT
This specification covers refined ruthenium as sponge and powder in one grade as follows: Grade 99.80 and Grade 99.90. The material may be produced by any refining process that yields a product capable of meeting the chemical requirements of this specification. The material should conform to the requirements for chemical composition as prescribed.
SCOPE
1.1 This specification covers refined ruthenium as sponge and powder in one grade as follows:  
1.1.1 Grade 99.80—Ruthenium having a purity of 99.80 %.  
1.1.2 Grade 99.90—Ruthenium having a purity of 99.90 %.  
Note 1: For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the limiting value in accordance with the rounding method of Practice E29.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B692-18(2023)(Specification)
Standard Specification for 75 % Silver-25 % Graphite Sliding Contact Material

ABSTRACT
This specification defines the criteria for the chemical composition and other requirements (including physical properties, microstructure, superficial hardness, and specific resistance ) for silver-graphite brushes for sliding electrical contacts. The percentage of silver, graphite, ash in graphite, and total metal impurities are prescribed. The minimum acceptable values for the physical properties such as density, determined by measurement and weight method, and shear strength are given. Typical Rockwell hardness and specific resistance for the material are also specified.
SCOPE
1.1 This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 75 weight % with the balance being substantially graphite.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off