ASTM E1272-02(2007)

Standard Specification for Laboratory Glass Graduated Cylinders

ABSTRACT
This specification covers the requirements for laboratory glass graduated cylinders for precision and general purpose grades. The graduated cylinders may be in one of three styles; beaded lip with spout, grounded standard taper neck, or beaded lip with pour spout and reinforcing band near the top. The products should conform to the required cylinder and base shapes, dimensions, quality of gradation and identification markings, and length of gradation lines.
SCOPE
1.1 This specification covers requirements for glass graduated cylinders for precision and general purpose grades suitable for laboratory purposes.
1.1.1 Class A  Each cylinder of precision grade shall be marked with the letter "A'' to signify compliance with applicable construction and accuracy requirements. Cylinders may be marked with an identification number (serial number) at the option of the manufacturer.
1.1.2 Class B  General purpose cylinders are of the same basic design as Class A cylinders. However, volumetric tolerances for Class B cylinders shall be within twice the specified range allowed for Class A cylinders. These cylinders need not be marked with their class designation.
1.1.3 Product with a stated capacity not listed in this standard may be specified in class A tolerance when product conforms to the tolerance range of the next smaller volumetric standard product listed in Table 1 .

General Information

• Status: Historical
• Publication Date: 31-Oct-2007
• ICS: 71.040.20 - Laboratory ware and related apparatus
• Technical Committee: E41 - Laboratory Apparatus
• Drafting Committee: E41.01 - Laboratory Ware and Supplies

Relations

• Replaces: ASTM E1272-02 - Standard Specification for Laboratory Glass Graduated Cylinders
• Effective Date: 01-Nov-2007
• Replaced By: ASTM E1272-02(2012) - Standard Specification for Laboratory Glass Graduated Cylinders
• Effective Date: 01-Nov-2012
• Referred By: ASTM D4164-13(2018) - Standard Test Method for Mechanically Tapped Packing Density of Formed Catalyst and Catalyst Carriers
• Effective Date: 01-Nov-2007
• Referred By: ASTM D5153-22 - Standard Test Method for Palladium in Molecular Sieve Catalyst by Atomic Absorption Spectrophotometry
• Effective Date: 01-Nov-2007
• Referred By: ASTM D8413-22 - Standard Guide for Measuring the Water Pore Volume of Catalytic Materials by Centrifuge
• Effective Date: 01-Nov-2007
• Referred By: ASTM D4180-13(2018) - Standard Test Method for Vibratory Packing Density of Formed Catalyst Particles and Catalyst Carriers
• Effective Date: 01-Nov-2007
• Referred By: ASTM D86-23 - Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
• Effective Date: 01-Nov-2007
• Referred By: ASTM D7442-22 - Standard Practice for Sample Preparation of Fluid Catalytic Cracking Catalysts, Catalytic Materials, and Zeolites for Elemental Analysis by Inductively Coupled Plasma Optical Emission Spectroscopy
• Effective Date: 01-Nov-2007
• Referred By: ASTM D7569/D7569M-10(2015)e1 - Standard Practice for Determination of Gas Content of Coal—Direct Desorption Method
• Effective Date: 01-Nov-2007
• Referred By: ASTM C940-22 - Standard Test Method for Expansion and Bleeding of Freshly Mixed Grouts for Preplaced-Aggregate Concrete in the Laboratory
• Effective Date: 01-Nov-2007
• Referred By: ASTM D7563-23 - Standard Test Method for Evaluation of the Ability of Engine Oil to Emulsify Water and Simulated Ed85 Fuel
• Effective Date: 01-Nov-2007
• Referred By: ASTM D8293-22 - Standard Guide for Evaluating and Expressing the Uncertainty of Radiochemical Measurements
• Effective Date: 01-Nov-2007
• Referred By: ASTM E133-92(2022) - Standard Specification for Distillation Equipment
• Effective Date: 01-Nov-2007
• Referred By: ASTM D4512-22 - Standard Test Method for Vibrated Apparent Packing Density of Fine Catalyst and Catalyst Carrier Particles and Powder
• Effective Date: 01-Nov-2007
• Referred By: ASTM D7603-23 - Standard Test Method for Determination of Storage Stability and Compatibility in Automotive Gear Oils
• Effective Date: 01-Nov-2007

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E1272 −02(Reapproved2007)
Standard Specification for Laboratory Glass
1
Graduated Cylinders
This standard is issued under the fixed designation E1272; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Laboratory Glassware
1.1 This specification covers requirements for glass gradu-
3. Classification
atedcylindersforprecisionandgeneralpurposegradessuitable
3.1 Cylinders shall be in the following styles:
for laboratory purposes.
3.1.1 Style I—Beaded lip with pour spout,
1.1.1 Class A—Each cylinder of precision grade shall be
3.1.2 Style II—Ground standard taper () neck, or
marked with the letter “A” to signify compliance with appli-
3.1.3 Style III—Beaded lip with pour spout and reinforcing
cable construction and accuracy requirements. Cylinders may
bead near top.
be marked with an identification number (serial number) at the
option of the manufacturer.
4. Requirements
1.1.2 Class B—General purpose cylinders are of the same
4.1 Style I cylinders shall be calibrated either “to deliver” or
basic design as Class A cylinders. However, volumetric toler-
“to contain.” Style II and Style III cylinders shall be calibrated
ances for Class B cylinders shall be within twice the specified
“to contain.” The cylinders shall be calibrated at 20°C and the
range allowed for Class A cylinders. These cylinders need not
volumetric tolerances shall be in accordance with Table 1. (See
be marked with their class designation.
Practice E542 for calibration definitions and procedures.)
1.1.3 Product with a stated capacity not listed in this
4.1.1 Cylinders shall be of borosilicate glass conforming to
standard may be specified in class A tolerance when product
the requirements for Type I, Class A of Specification E438.
conforms to the tolerance range of the next smaller volumetric
standard product listed in Table 1.
4.2 Shape—Cylinders shall be of one piece consisting in
general of a top, a graduated portion of uniform diameter and
2. Referenced Documents
a base. The shape shall permit complete emptying and thor-
2
2.1 ASTM Standards:
oughcleaning.Thepour-outofStyleI,insizesof1000mLand
E438 Specification for Glasses in Laboratory Apparatus
below, shall be located in a vertical plane bisecting within 65°
E542 Practice for Calibration of Laboratory Volumetric
one of the corners on the hexagonal base. For sizes 2000 mL
Apparatus
and above, the pour-out shall bisect within 65° the center of
E675 Specification for Interchangeable Taper-Ground Stop-
one of the flat section or one of the corners of the base. The
cocks And Stoppers
pour-out of Style III shall not protrude beyond the glass
E920 Specification for Commercially Packaged Laboratory
reinforcing bead with construction such that, upon falling, the
Apparatus
bead shall strike a flat surface before the pour-out or lip.
E921 Specification for Export Packaged Laboratory Appa-
4.2.1 Base—The base shall be hexagonal and the construc-
ratus
tion shall be such that the empty cylinder (without stopper for
E1133 Practice for Performance Testing of Packaged Labo-
Style II), in capacities above 10 mL, shall stand on a surface
ratory Apparatus for United States Government Procure-
inclined 15° with the horizontal and, in capacities of 10 mL or
ments
less, shall stand on a surface inclined 10° with the horizontal.
E1157 Specification for Sampling and Testing of Reusable
4.3 Dimensions—The dimensions shall be as shown in
Table 1 The glass stoppers of Style II shall conform to
Specification E675.
1
This specification is under the jurisdiction of ASTM Committee E41 on
Laboratory Apparatus and is the direct responsibility of Subcommittee E41.01 on
4.4 Graduation Markings—Graduation markings shall be
Apparatus.
sharply defined lines of uniform width not more than 0.4 mm.
Current edition approved Nov. 1, 2007. Published November 2007. Originally
Graduation markings shall be perpendicular to the vertical axis
approved in 1989. Last previous edition approved in 2002 as E1272 – 02. DOI:
10.1520/E1272-02R07.
of the cylinder and parallel to each other. Adjacent graduation
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
markings shall be spaced at least 1 mm from center to center.
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Markings shall be applied by one of the following methods:
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. etched and filled with a permanent pigment; etched through a
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United St
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E1272–95 (Reapproved 1999) Designation: E 1272 – 02 (Reapproved 2007)
Standard Specification for Laboratory Glass
1
Graduated Cylinders
This standard is issued under the fixed designation E 1272; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers requirements for glass graduated cylinders for precision and general purpose grades suitable for
laboratory purposes.
1.1.1 Class A—Each cylinder of precision grade shall be marked with the letter “A’’ to signify compliance with applicable
construction and accuracy requirements. Cylinders may be marked with an identification number (serial number) at the option of
the manufacturer.
1.1.2 Class B—General purpose cylinders are of the same basic design as Class A cylinders. However, volumetric tolerances
for Class B cylinders shall be within twice the specified range allowed for ClassAcylinders. These cylinders need not be marked
with their class designation.
2.
1.1.3 Product with a stated capacity not listed in this standard may be specified in classAtolerance when product conforms to
the tolerance range of the next smaller volumetric standard product listed in Table 1.
2
2. Referenced Documents
2.1 ASTM Standards:
E 438 Specification for Glasses in Laboratory Apparatus
2
E 542 Practice for Calibration of Laboratory Volumetric Ware Apparatus
2
E 675Specification for Interchangeable Taper-Ground Stopcocks and Stoppers
2
E694Specification for Volumetric Ware Specification for Interchangeable Taper-Ground Stopcocks And Stoppers
E 920 Specification for Commercially Packaged Laboratory Apparatus
E 921 Specification for Export Packaged Laboratory Apparatus
E 1133 Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements
E 1157 Specification for the Sampling and Testing of Reusable Laboratory Glassware
3. Classification
3.1 Cylinders shall be in the following styles:
3.1.1 Style I— Beaded lip with pour spout,
3.1.2 Style II—Ground standard taper () neck, or
3.1.3 Style III—Beaded lip with pour spout and reinforcing bead near top.
4. General Requirements
4.1 Style I cylinders shall be calibrated either “to deliver’’ or“ to contain.’’ Style II and Style III cylinders shall be calibrated“
to contain.’’ The cylinders shall be calibrated at 20°C and the volumetric tolerances shall be in accordance with Table 1. (See
Practice E 542 for calibration definitions and procedures.)
4.1.1 Cylinders shall be of borosilicate glass conforming to the requirements for Type I, Class A of Specification E 438.
4.2 Shape—Cylinders shall be of one piece consisting in general of a top, a graduated portion of uniform diameter and a base.
The shape shall permit complete emptying and thorough cleaning. The pour-out of Style I, in sizes of 1000 mL and below, shall
be located in a vertical plane bisecting within 65° one of the corners on the hexagonal base. For sizes 2000 mL and above, the
pour-out shall bisect within 65° the center of one of the flat section or one of the corners of the base. The pour-out of Style III
1
This specification is under the jurisdiction of ASTM Committee E-41 on Laboratory Apparatus and is the direct responsibility of Subcommittee E41.01 on Apparatus.
Current edition approved Feb. 15, 1995. Published April 1995. Originally published as E1272–89. Last previous edition E1272–89.
1
This specification is under the jurisdiction of ASTM Committee E41 on Laboratory Apparatus and is the direct responsibility of Subcommittee E41.01 on Apparatus.
Current edition approved Nov. 1, 2007. Published November 2002. Originally approved in 1989. Last previous edition approved in 2002 as E 1272 – 02.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 14.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E 1272 – 02 (2007)
TABLE 1 Dimensions and Tolerances
Maximum
Distance From Scale to Tolerances to Contain or to
Minimum Standard Taper
Graduations, Inner
Top, mm Deliver 6 mL
A
Capacity, mL Main Least Wall Thick-
...