ASTM D6261-13

Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)

ABSTRACT
This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic polyester. Each type of thermoplastic polyester shape may be categorized into one of several grades as follows: grade 1 - general purpose-extruded or compression molded product made using only 100 % virgin thermoplastic polyester resin and grade 2 - recycled-extruded or compression molded product made using any amount up to 100 % recycled thermoplastic polyester plastics. Tensile stress break, elongation at break, and tensile modulus shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic polyester.  
1.2 The properties included in this specification are those required for the compositions covered. Use the classification system given in Section 4 to describe requirements necessary to identify particular characteristics important to specialized applications.  
1.3 This specification allows the use of recycled plastics2 (see Section 4).  
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1 and Table S-TPES only.  
1.5 The following precautionary caveat pertains only to the test method portions sections of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1—There is no known ISO equivalent to this specification.

General Information

• Status: Historical
• Publication Date: 30-Sep-2013
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: D20 - Plastics
• Drafting Committee: D20.15 - Thermoplastic Materials

Relations

• Replaces: ASTM D6261-10 - Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
• Effective Date: 01-Oct-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6261 −13
StandardSpecification for
Extruded and Compression Molded Basic Shapes Made
1
from Thermoplastic Polyester (TPES)
This standard is issued under the fixed designation D6261; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification is intended to be a means of calling out mechanical grade plastic product used in
the fabrication of end items or parts.
1. Scope* 2. Referenced Documents
3
1.1 This specification covers requirements and test methods 2.1 ASTM Standards:
for the material, dimensions, and workmanship, and the prop- D256 Test Methods for Determining the Izod Pendulum
erties of extruded and compression molded plate, rod and Impact Resistance of Plastics
tubular bar manufactured from thermoplastic polyester. D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
1.2 The properties included in this specification are those
D790 Test Methods for Flexural Properties of Unreinforced
required for the compositions covered. Use the classification
and Reinforced Plastics and Electrical Insulating Materi-
system given in Section 4 to describe requirements necessary
als
to identify particular characteristics important to specialized
D883 Terminology Relating to Plastics
applications.
D3892 Practice for Packaging/Packing of Plastics
2
1.3 This specification allows the use of recycled plastics
D4507 Specification for Thermoplastic Polyester (TPES)
4
(see Section 4).
Materials (Withdrawn 1999)
1.4 The values are stated in inch-pound units and are D4000 Classification System for Specifying Plastic Materi-
als
regarded as the standard in all property and dimensional tables.
For reference purposes, SI units are also included in Table 1 D5927 Classification System for Thermoplastic Polyester
(TPES) Injection and Extrusion Materials Based on ISO
and Table S-TPES only.
Test Methods
1.5 The following precautionary caveat pertains only to the
D7209 Guide for Waste Reduction, Resource Recovery, and
test method portions sections of this specification.This stan-
Use of Recycled Polymeric Materials and Products
dard does not purport to address all of the safety concerns, if
any, associated with its use. It is the responsibility of the user
3. Terminology
of this standard to establish appropriate safety and health
3.1 Definitions:
practices and determine the applicability of regulatory limita-
3.1.1 For definitions of other technical terms pertaining to
tions prior to use.
plastics used in this specification, see Terminology D883 or
NOTE 1—There is no known ISO equivalent to this specification.
Guide D7209.
3.2 Definitions of Terms Specific to This Standard:
1
This specification is under the jurisdiction of ASTM Committee D20 on
3
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Materials (Section D20.15.21). contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Current edition approved Oct. 1, 2013. Published October 2013. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1998. Last previous edition approved in 2010 as D6261 - 10. DOI: the ASTM website.
4
10.1520/D6261-13. The last approved version of this historical standard is referenced on
2
As defined in Guide D7209. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6261−13
1
3.2.1 plate, n—flat stock ⁄4 in. (6.4 mm) or greater.
Tolerance
Symbol Material (Based on the Total Mass)
3.2.2 recycled-plastic shape, n—a product made from up to
100 % recycled plastic. C Carbon and graphite fiber ±2%
reinforced
3.2.3 rod, n—a solid cylindrical shape with a minimum
G Glass-reinforced
1
diameter of ⁄8 in. (3.2 mm). < 15 % glass content ± 2 %
> 15 % glass content ± 3 %
3.2.4 tubular bar, n—anannularshapewithminimuminside
L Lubricants (for example, by agreement between the supplier
3 1
PTFE, graphite and and the user
diameterof ⁄8 in.(9.6mm)andminimumwallthicknessof ⁄16
silicone
in. (1.6 mm).
M Mineral ± 2 %
R Combinations of ± 3 % for the total reinforcement
reinforcements or
4. Classification and Material
fillers, or both
4.1 Product shape and size as defined in the applicable
4.5 Callout Designation—Aone-linesystemshallbeusedto
purchase order.
specify thermoplastic polyester materials covered by this
specification. The system use
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6261 − 10 D6261 − 13
Standard Specification for
Extruded and Compression Molded Basic Shapes Made
1
from Thermoplastic Polyester (TPES)
This standard is issued under the fixed designation D6261; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification is intended to be a means of calling out mechanical grade plastic product used in
the fabrication of end items or parts.
1. Scope Scope*
1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties
of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic polyester.
1.2 The properties included in this specification are those required for the compositions covered. Use the classification system
given in Section 4 to describe requirements necessary to identify particular characteristics important to specialized applications.
2
1.3 This specification allows the use of recycled plastics (see Section 4).
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For
reference purposes, SI units are also included in Table 1 and Table S-TPES only.
1.5 The following precautionary caveat pertains only to the test method portions sections of this specification.This standard does
not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
NOTE 1—There is no known ISO equivalent to this specification.
2. Referenced Documents
3
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D883 Terminology Relating to Plastics
D3892 Practice for Packaging/Packing of Plastics
4
D4507 Specification for Thermoplastic Polyester (TPES) Materials (Withdrawn 1999)
D4000 Classification System for Specifying Plastic Materials
4
D5033 Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics (Withdrawn 2007)
D5927 Classification System for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods
D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products
2.2 ANSI Standard:
5
Z1.4-1993 Sampling Procedures and Tables for Inspection by Attributes
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.20D20.15 on Plastic
LumberThermoplastic Materials (Section D20.20.02).D20.15.21).
Current edition approved June 1, 2010Oct. 1, 2013. Published August 2010October 2013. Originally approved in 1998. Last previous edition approved in 20032010 as
D6261 - 98D6261 - 10.(2003). DOI: 10.1520/D6261-10.10.1520/D6261-13.
2
As defined in Guide D5033D7209.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6261 − 13
3. Terminology
3.1 Definitions:
3.1.1 For definitions of other technical terms pertaining to plastics used in this specification, see Terminology D883 or Guide
D5033D7209.
3.2 Definitions of Terms Specific to This Standard:
1
3.2.1 plate, n—flat stock ⁄4 in. (6.4 mm) or greater.
3.2.2 recycled-plastic shape, n—a product made from up to 100 % recycled plastic.
1
3.2.3 rod, n—an extruded a solid cylindrical shape with a minimum diameter of ⁄8 in. (3.2 mm).
3
3.2.4 tubular bar, n—an extruded annular shape with minimum inside diameter of ⁄8 in. (9.6 mm) and minimum wall thickness
...